• The Journal of Engineering Geology
• /
• v.14 no.1
• /
• pp.71-80
• /
• 2004

The failure of cut slopes frequently occurs particularly during the thawing season and the rain season in summer. This study interpreted data collected from site to which a real-monitoring system was applied in order to analyze the causes of ground behaviors and to forecast future slope failure. As for research methods, this study analyzed the size and mechanism of failure by integrating the results of field surveys and measurements. Furthermore, it analyzed data transmitted by the monitoring system installed in the a result, three times of ground displacement occurred as well as a number of partial tension cracks. The cut slope composed of sandstone and siltstone started its initial behavior as a result of torrential downpour and the loss of support of the substructure. For quantitative analysis of the characteristics of ground behavior, this study measured 5 lateral lines. According to the result of the measurement, displacement happened little in the section to which countermeasure had been applied, but displacement of maximum 400mm happened in the section to which countermeasure had not bee applied. The analysis of data on displacement and rainfall suggested a close relationship between ground behavior and rainfall. According to the result of stability interpretation along with the change of ground saturation, stability rate appeared to be less than 1.0 when ground saturation is over 55%. Although the current trend of ground behavior is at a stable stage falling within the range of tolerance, it is considered necessary to continue monitoring and data analysis because ground displacement is highly possible with the change of temperature during the winter.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.2
• /
• pp.129-140
• /
• 2018

A residual stress generated in the steel structure is broadly categorized into initial residual stress during manufacturing steel material, welding residual stress caused by welding, and heat treatment residual stress by heat treatment. Initial residual stresses induced during the manufacturing process is combined with welding residual stress or heat treatment residual stress, and remained as a final residual stress. Because such final residual stress affects the safety and strength of the structure, it is of utmost importance to measure or predict the magnitude of residual stress, and to apply this point on the design of the structure. In this study, the initial residual stress of steel structures having thicknesses of 25 mm and 70 mm during manufacturing was measured in order to investigate initial residual stress (hereinafter, referred to as initial stress). In addition, thermal elastic plastic FEM analysis was performed with this initial condition, and the effect of initial stress on the welding residual stress was investigated. Further, the reliability of the FE analysis result, considering the initial stress and welding residual stress for the steel structures having two thicknesses, was validated by comparing it with the measured results. In the vicinity of the weld joint, the initial stress is released and finally controlled by the weld residual stress. On the other hand, the farther away from the weld joint, the greater the influence of the initial stress. The range in which the initial stress affects the weld residual stress was not changed by the initial stress. However, in the region where the initial stress occurs in the compressive stress, the magnitude of the weld residual compressive stress varies with the compression or tension of the initial stress. The effect of initial stress on the maximum compression residual stress was far larger when initial stress was considered in case of a thickness of 25 mm with a value of 180 MPa, while in case of thickness at 70 mm, it was 200 MPa. The increase in compressive residual stress is almost the same as the initial stress. However, if initial stress was tensile, there was no significant change in the maximum compression residual stress.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.4
• /
• pp.357-364
• /
• 1999

This study measures the influence of grass cover on water use and shoot growth of apple trees growing under different soil water regimes in temperate climate conditions and evaluates monthly crop coefficients of such conditions during four months of the growing season in 1995. To do so, double pot lysimeter experiments of 3-year-old Fuji' apple (Males domestica Borkh.) trees under a transparent rain shield were designed and installed. Trees were triplicate under three soil water regimes: (A) drip-irrigation at -50 kPa of soil matric potential (IR50). (B) drip-irrigation at -80 kPa of soil matric potential (IR80), and (C) constant shallow water table at 0.45 m below the soil surface (WT45). In each treatment, two soil surface conditions were tested: the soil surface bare, and covered with turf grasses. Mean monthly water use increased with increasing soil matric potential for drip irrigation and was greatest in the WT45 treatment. Monthly crop coefficients increased linearly in time for drip-irrigated apple trees ($r^2$ values of $0.953^{***}$ for turf grass-covered system and of $0.862^{***}$ for bare surface system), while those obtained in the WT45 treatment fluctuated, Duncan's multiple range tests for shoot growth showed that grass-covered IR50 was most favorable to apple trees. while bare surface waterlogged situation was most adverse at least in part due to a lack of oxygen in the root zone. Mid-season leaf Kjeldahl-N was higher in drip-irrigated apple trees than in WT45 trees, while soil Kjeldahl-N was not different irrespective of treatments.

• Annals of Geriatric Medicine and Research
• /
• v.22 no.4
• /
• pp.176-183
• /
• 2018

Background: Although the frequency and intensity of headaches decrease in older adults, headaches in this population are still an important neurological disorder. The purpose of this study was to investigate the associations of headache characteristics in older adults with the development of cardiovascular disease and cognitive dysfunction. Methods: We prospectively enrolled 125 older (${\geq}65$ years old) patients with headache who were making their first visit to outpatient clinics and who had no prior history of cognitive dysfunction from 11 hospitals in Korea between August 2014 and February 2015. We investigated the occurrence of newly developed/or recurrent headache, cardiovascular disease, cognitive dysfunction, and poor functional outcomes. Results: The mean age of all included patients was 72.6 years, 68.8% were women, and 43 (34.4%) had newly developed/or recurrent headache during follow-up. During a median follow-up of 31 months (interquartile range, 28-34 months), 21 participants (16.8%) experienced cardiovascular disease, and 26 (20.8%) developed cognitive dysfunction. Upon multivariate analysis and after adjusting for sex, age, and other factors, presence of newly developed/or recurrent headache was found to be associated with cardiovascular disease (hazard ratio [HR], 4.03; 95% confidence interval [CI], 1.28-12.61; p=0.017) and frequency of headache for the recent 3 months was related with cognitive dysfunction (HR, 1.05; 95% CI, 1.00-1.09; p=0.017) and poor functional outcomes (HR, 1.06; 95% CI, 1.01-1.11; p=0.011). Conclusion: Our study demonstrated that there is an increased risk of cardiovascular disease, cognitive dysfunction, and poor functional outcomes in older patients with frequent, newly developed, or recurrent headache.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.05a
• /
• pp.135-137
• /
• 2019

In recent years, the need for ship-to-ship has emerged around the world as the volume of tanker carriers increases. In the case of STS mooring, a safety review should be carried out on other standards since the characteristics are different from the mooring at a typical wharf. However, there is no separate standard about STS in Korea. Therefore, in this study, STS mooring simulation and sensitivity analysis were performed using OPTIMOOR program, a commercial numerical analysis program, to identify STS mooring characteristics. The target sea area is modeled at D2 anchorage of Yeosu Port in Korea, and modeling of the target ship is selected as the case of VLCC-VLCC. Based on this, we tried to establish the standard for STS mooring safety evaluation. Numerical simulation results show that the STS mooring changes depending on the ship load condition, weather condition(wave period and wave height), encounter angle and pre-tension of mooring line. In addition, a risk matrix was created to set the safe external force range in the sea area. It is expected that the mooring characteristics of the STS can be grasped by this result and contribute to the revision of the mooring safety assessment standard.

• Applied Chemistry for Engineering
• /
• v.30 no.3
• /
• pp.303-307
• /
• 2019

Sophorolipid is a biological surfactant of the glycolipid structure produced by Candida bombicola, which generally exists as a mixture of acidic and lactonic forms. In this study, we investigated physico-chemical properties, antibacterial activities, and cytotoxicity of the sophorolipid containing more than 96% of the lactonic form, produced by the gene regulation of production strains and application of a metabolic engineering technique. The lactonic sophorolipid showed a weak acidity in the range of pH 3.2~4.6 when diluted in water at the concentrations from 1 to 0.001 wt%. The $pK_a$ value of the lactonic sophorolipid was estimated to be around 4.3 from the acid-base titration curve. The critical micelle concentration (CMC) of the lactonic sophorolipid was $10^{-2}wt%$, at which the surface tension of aqueous solution was reduced to 36 mN/m. The lactonic sophorolipid showed the minimum inhibitory concentrations (MIC) of $1{\times}10^{-3}$ and $5{\times}10^{-3}g/mL$ against Propionibacterium acnes and Corynebacterium xerosis, respectively. The MTT (3-(4,5-Dimethylthiazol-2-yl)-2,5-Diphenyltetrazolium Bromide] assay showed that cytotoxicity of the lactonic sophorolipid was ten times lower than that of triclosan.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.32 no.2
• /
• pp.81-86
• /
• 2021

Background and Objectives Therapies have been reported to treat the glottal gap previously. However, these voice therapies showed the limits because many techniques focused only on one among breathing, resonance and phonation. In addition patients often have difficulties visiting hospital frequently. 'Gliding and humming' is vocal training technique that readjusts total vocal patterns such as breathing, resonance and phonation. This technique can be easily applied during short term sessions. The purpose of this study is to evaluate the efficiency of voice therapy with 'gliding and humming' for patients with glottic gap during short-term treatment sessions. Materials and Method Twenty-three patients with glottal gap were selected. Of all patients, 14 patients had sulcus vocalis and 12 patients had muscle tension dysphonia (MTD). Voice therapies were performed 1.9 sessions in average. GRBAS, jitter, shimmer, noise to harmonic ratio, semitone range, closed quotient_vowel and maximum phonation time were compared before and after the therapies. In addition, changes of glottal gap and MTD severity were evaluated. Results Statistically significant improvement was observed. MTD improvement was observed only among the patients with glottal gap improvement. Also sulcus vocalis group showed the statistically significant improvement. Conclusion 'Gliding and humming' was effective to the patients with glottic gap and sulcus vocalis. Also, among patients who have both glottic gap and MTD, the data suggests that voice therapy for glottic gap also makes improvement in MTD.

• Journal of East Asia Management
• /
• v.4 no.1
• /
• pp.23-51
• /
• 2023

We investigate whether the association between management overconfident tone and the level of audit effort measured by audit fees and hours differs depending on the level of earnings management. Prior studies suggest that firms led by overconfident managers are likely to initiate risky investments, report low quality financial statements, and have material weaknesses in internal control system. These characteristics, combined together, result in higher audit risk. At the same time, auditors assess audit risk based on the quality of financial reporting, measured by level of earnings management. As a result, the assess audit risk is likely to reflect the combined effect of management overconfidence and the level of earnings management. In this paper, we investigate whether auditors differentiate the effects of real earnings management (REM) and accrual-based earnings management (AEM) when they assess the audit risk related management overconfident. Using the CEO's letter published in 2018, we measure the CEO's tone representing the degree of overconfidence (i.e., activity). Based on this measure, we find that the positive association between managerial overconfident tone and audit effort is more pronounced as the level of REM is higher. However, we find that the baseline association does not vary depending on the level of AEM. These results suggest that auditors consider the managerial overconfident severer when such characteristic accompany the higher level of REM, which can be outcome of aggressive business decisions possibly leading to the higher audit risks. We further find that these results are stronger for Big 4 auditors and continuing auditors. This paper contributes to the literature and practice as follows. First, we provide contextual evidence on how auditors reflect managerial characteristics in the audit process by documenting that auditors actively increase their audit efforts only when overconfident managerial characteristics are highly likely to lead to audit risk. This result suggests that auditors conduct external auditing considering both the efficiency and effectiveness of the audit process. Second, we suggest that auditors use information obtained from a wide range of sources to identify audit risks. Our results provide evidence of how the auditing standards, which do not provide detailed guidelines for audit risk assessment, are being applied in practice. Finally, our results also enhance the understanding of how audit fees are determined. Combined with the studies related to audit pricing, we provide the important reference for discussion between the auditor and the auditee about the audit fee that has created acute tension after the enforcement of the new External Audit Act.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.2
• /
• pp.161-167
• /
• 2011

The soil moisture has an important effect on growth and development of highbush blueberry (HB), mainly because the root system, devoid of root hairs, is superficial. Moreover, the texture and organic matter content of Korean soil is different from the main producing counties, such as USA and Canada. To facilitate the growth and development of HB and long-term maintenance of productivity, the research related to soil moisture condition in Korea should be the priority. This study was performed to investigate the growth properties of the HB in various soil moisture conditions in order to determine the irrigation trigger point and optimum soil water potential. The texture of soil used in this experiment was loam. For the experiments, the soil was mixed with peatmoss at a rates 30% (v/v). Irrigation was scheduled at -3, -4, -5, -8, -15 and -22 kPa soil water potential then investigated leaf macronutrient, bush growth, and fruit properties. The leaf K content of HB showed the same trend in the soil water potential, but Leaf P and Mg content was highest in -5 and -22 kPa, respectively. The productivity and growth amount of HB showed the peak at the range of -4~-8 kPa as normal distribution pattern, and greatly decreased at above -15 kPa. Total dry weight and Cane diameter were highest at -4 kPa, plant width, fruit weight and yield were highest at -5 kPa, and plant height, cane number and shoot tension were highest at -8 kPa. Soluble solids content showed same trend in the soil water potential, but titratable acidity, anthocyanins and total polyphenols were not significantly different. Therefore, the optimal soil water potential for the development and a maximum production of HB were a range of -4~-8 kPa, and the recommended ideal irrigation trigger point was within -15 kPa.

• Applied Biological Chemistry
• /
• v.39 no.3
• /
• pp.172-176
• /
• 1996

Effect of culture conditions such as pH, temperature, agitation speed and oxygen transfer rate on xylitol production from xylose by Candide parapsilosis ATCC 21019 mutant was investigated in a jar fermentor. The initial concentration of xylosr was fixed at 50 g/l in this experiment. When pH was increased, cell growth and xylose consumption rate were increased, but maximum xylitol production was shown in the range of pH 4.5 and 5.5 with a yield of 0.68 g/g-xylose. The optimal temperature for xylitol production was determined to be $30^{\circ}C$. Considering the importance of dissolved oxygen tension, for xylitol production, the effect of oxygen transfer rate coefficient $(k_La)$ on fermentation parameters was carefully evaluated in the range of $20{\sim}85\;hr{-1}\;of\;k_La$ (corresponding to $100{\sim}300$rpm of agitation speed). The xylitol production was maximized at $30\;hr^{-1}\;of\;k_La$(150 rpm). A higher oxygen transfer rate supported better cell growth with lower xylitol yield. It was determined that maximum xylitol concentration, xylitol yield and productivity was 35.8 g/l, 71.6% and $0.58\;g/l{\sim}hr^{-1}$, respectively, at $30\;hr^{-1}\;of\;k_La$ In order to further increase xylitol productivity, ferementation using the concentrated biomass(20 g/l) was carried out at the conditions of pH 4.5, $30^{\circ}C$ and $30\;hr\;1$ of oxygen transfer rate. The final xylitol concentration of 40 g/l was obtained at 18 hours of culture time. From this result, it was calculated that xylitol yield was 80ft on the basis of xylose consumption and volumetric productivity was $2.22\;g/l{\sim}hr$ which was increased by $3{\sim}4$ fold compared with $0.5{\sim}0.7\;g/l-hr$ obtained in a normal fermentation condition.