International Journal of Naval Architecture and Ocean Engineering

The Society of Naval Architects of Korea (대한조선학회)
권호 표지
DOI QR코드

DOI QR Code

The effect of initial stress induced during the steel manufacturing process on the welding residual stress in multi-pass butt welding

  • Park, Jeong-ung (Dept. of Civil Engineering, Chosun University) ;
  • An, Gyubaek (Dept. of Naval Architecture and Ocean Engineering, Chosun University) ;
  • Woo, Wanchuck (KAERI, Neutron Science Division)
  • Received : 2016.10.05
  • Accepted : 2017.02.26
  • Published : 2018.03.31
Download PDF
⟨ Previous Next ⟩

Abstract

A residual stress generated in the steel structure is broadly categorized into initial residual stress during manufacturing steel material, welding residual stress caused by welding, and heat treatment residual stress by heat treatment. Initial residual stresses induced during the manufacturing process is combined with welding residual stress or heat treatment residual stress, and remained as a final residual stress. Because such final residual stress affects the safety and strength of the structure, it is of utmost importance to measure or predict the magnitude of residual stress, and to apply this point on the design of the structure. In this study, the initial residual stress of steel structures having thicknesses of 25 mm and 70 mm during manufacturing was measured in order to investigate initial residual stress (hereinafter, referred to as initial stress). In addition, thermal elastic plastic FEM analysis was performed with this initial condition, and the effect of initial stress on the welding residual stress was investigated. Further, the reliability of the FE analysis result, considering the initial stress and welding residual stress for the steel structures having two thicknesses, was validated by comparing it with the measured results. In the vicinity of the weld joint, the initial stress is released and finally controlled by the weld residual stress. On the other hand, the farther away from the weld joint, the greater the influence of the initial stress. The range in which the initial stress affects the weld residual stress was not changed by the initial stress. However, in the region where the initial stress occurs in the compressive stress, the magnitude of the weld residual compressive stress varies with the compression or tension of the initial stress. The effect of initial stress on the maximum compression residual stress was far larger when initial stress was considered in case of a thickness of 25 mm with a value of 180 MPa, while in case of thickness at 70 mm, it was 200 MPa. The increase in compressive residual stress is almost the same as the initial stress. However, if initial stress was tensile, there was no significant change in the maximum compression residual stress.

Keywords

References

  1. An, G.B. (Ed.), 2011. The Proceedings of the Twenty-first (2011) International Offshore and Polar Engineering Conference; 2011 June 19-24; Maui.
  2. An, Gyu Baek, Woo, Wanchuck, Park, Jeong-Ung, 2014. Brittle crack-arrest fracture toughness in a high heat-input thick steel weld. Int. J. Fract. 185 (1-2), 179-185. https://doi.org/10.1007/s10704-013-9900-x
  3. Birkholz, M., Genzel, C., Jung, T., 2004. X-ray diffraction study on residual stress and preferred orientation in thin titanium films subjected to a high ion f lux during deposition. J. Appl. Phys. 96, 7202. https://doi.org/10.1063/1.1814413
  4. Brust, F.W., Dong, P., Zhang, J., Cao, Z., Yang, Y.P., Hong, J.K., 1998. Weld Process Modeling and It's Importance in a Manufacturing Environment (No. 981510). SAE Technical Paper.
  5. Chounga, Joonmo, Nama, Ji-Myung, Tayyarb, Gokhan Tansel, 2014. Residual ultimate strength of a very large crude carrier considering probabilistic damage extents. Int. J. Nav. Archit. Ocean Eng. 6 (1), 14-26. https://doi.org/10.2478/IJNAOE-2013-0160
  6. Dean, D., Shoichi, K., 2010. Numerical simulation of residual stresses induced by laser beam welding in a SUS316 stainless steel pipe with considering initial residual stress influences. Nucl. Eng. Des. 240 (2010), 68-695.
  7. Dong, P., Cahill, P., Yang, Z., Chen, X.L., Mattei, N.J., 2004. Plate residual stress effects on dimensional accuracy in thermal cutting. J. Ship Prod. 20 (4), 245-255.
  8. Fuchs, Henry Otten, Stephens, I., 1980. Metal Fatigue in Engineering. John Wiley & Sons, NY.
  9. Haagensen, P.J., Maddox, S.J., 1995. IIW Recommendations on Post Weld Improvement of Steel and Aluminium Structures. IIW Doc. XIII-2200r1-07, 2008. -Tig dressing. Collaborative test program on improvement techniques.
  10. Haagensen, P.J.,Maddox, S.J., 2001. Specifications forWeldToe Improvement by BurrGrinding, Tig Dressing andHammer Peening for TransverseWelds. IIW Commission XII-Working Group 2, WG2. International Institute of Welding.
  11. Hansen, A.V., Agerskov, H., Bjornbak-Hansen, J., 2005. Improvement of Fatigue Life of Welded Structural Components by Grinding, IIW Doc. XIII-2051-05, 2005.
  12. Jeom Kee, Paik, Thayamballi, Anil K., Kim, Do Hyung, 1999. An analytical method for the ultimate compressive strength and effective plating of stiffened panels. J. Constr. Steel Res. 49 (1), 43-68. https://doi.org/10.1016/S0143-974X(98)00207-7
  13. Jiang, W., Woo, W., An, G.B., Park, J.U., 2013. Neutron diffraction and finite element modeling to study the weld residual stress relaxation induced by cutting. Mater. Des. 51, 415-420. https://doi.org/10.1016/j.matdes.2013.04.053
  14. Kang, S.W., Kim, M.H., Choi, J.Y., Kim, W.S., Paik, Y.M., 2006. A study on the fatigue strength improvement using weld toe burr grinding. J. KWS 24 (2), 150-155.
  15. Kim, H.J., Bae, K.Y., 1991. Cutting camber of TMCP steel plates. J. Korean Weld. Soc. 9 (1), 9-15.
  16. Kim, Seong-Min, Kim, Myung-Hyun, 2015. Incorporating mesh-insensitive structural stress into the fatigue assessment procedure of common structural rules for bulk carriers. Int. J. Nav. Archit. Ocean Eng. 7 (1), 0-24. https://doi.org/10.1515/ijnaoe-2015-0002
  17. Luo, Y., 1997. Description of Inherent Strain and its Application to Prediction of Welding Deformation and Residual Stress under Multi-pass Welding. Doctoral Thesis. Osaka University.
  18. Mahmoudi, A.H., Hossain, S., Pavier, M.J., Truman, C.E., Smith, D.J., 2009. A new procedure to measure near yield residual stresses using the deep hole drilling technique. Exp. Mech. 49 (4), 595-604. https://doi.org/10.1007/s11340-008-9164-y
  19. McClung, R.C., 2007. A literature survey on the stability and significance of residual stresses during fatigue. Fatigue & Fract. Eng. Mater. Struct. 30 (3), 173-205. https://doi.org/10.1111/j.1460-2695.2007.01102.x
  20. Murakawa, H., Luo, Y., Ueda, Y., 1996. Prediction of welding deformation and residual stress by elastic FEM based on inherent strain (first report) mechanism of inherent strain production. J. Soc. Nav. Arch. Jpn. 180, 739-751.
  21. Okido, S., Hayashi, M., Tanaka, K., Akinawa, Y., Minakawa, N., Mori, Y., April 1999. Measurement of residual stress in textured Al alloy by neutron diffraction method. In: 7th International Conference on Nuclear Engineering(ICONE), Tokyo, Japan, pp. 19-23.
  22. Park, Jeong-Ung, 1997. A Study on Prediction and Mechanism of Out-of-plane Deformation in Butt Joint with Initial Defects. Ph.D thesis. Osaka university.
  23. Park, Jeong-Ung, et al., 2011. Development of fatigue life improvement technology of butt joints using friction stir processing. Adv. Mech. Eng. 6, 943476.
  24. Park, Jeong-Ung, et al., 2014a. Residual stress measurement in an extra thick multi-pass weld using initial stress integrated inherent strain method. Mar. Struct. 39, 424-437.
  25. Park, Jeong-Ung, et al., 2014b. Comparison of measured residual stress distributions in extra-thick butt welds joined by one-pass EGW and multipass FCAW. Adv. Mech. Eng. 6, 861247. https://doi.org/10.1155/2014/861247
  26. Prime, M.B., 2001. Cross-sectional mapping of residual stresses by measuring the surface contour after a cut. J. Eng. Mater. Technol. 123, 162-168. https://doi.org/10.1115/1.1345526
  27. Real, PMM Vila, et al., 2004. The effect of residual stresses in the lateraltorsional buckling of steel I-beams at elevated temperature. J. Constr. Steel Res. 60 (3), 783-793. https://doi.org/10.1016/S0143-974X(03)00143-3
  28. Sicot, O., et al., 1999. Influence of experimental parameters on determination of residual stress using the incremental hole-drilling method. Compos. Sci. Technol. 64 (2), 171-180. https://doi.org/10.1016/S0266-3538(03)00278-1
  29. Smith, D.J., Bouchard, P.J., George, D., 2000. Measurement and prediction of residual stresses in thick-section steel welds. J. Strain Anal. Eng. Des. 35 (4), 287-305. https://doi.org/10.1243/0309324001514422
  30. Statnikov, E.S., Muktepavel, V.O., Blomqvist, A., 2002. Comparison of ultrasonic impact treatment (UIT) and other fatigue life improvement methods. Weld. World 46, 28-39. https://doi.org/10.1007/BF03266363
  31. Tryfyakov, V.I., Mikheev, P.P., Kudryavtsev, Y.F., Reznik, D.N., 1993. Ultrasonic impact peening treatment of welds and its effect on fatigue resistance in air and seawater. In: Offshore Technology Conference, Paper OTC 7280.
  32. Ueda, Y., Nakacho, K., Shimizu, T., 1986. Improvement of residual stresses of circumferential joint of pipe by heat-sink welding. J. Press. Vessel Technol. 108 (1), 14-23. https://doi.org/10.1115/1.3264746
  33. Ueda, Yukio, et al., 1994. FEM simulation of gas and plasma cutting with emphasis on precision of cutting (mechanics, strength & structural design). Trans. JWRI 23 (1), 93-102.
  34. Uy, B., 1998. Local and post-local buckling of concrete filled steel welded box columns. J. Constr. Steel Res. 47 (1), 47-72. https://doi.org/10.1016/S0143-974X(98)80102-8
  35. Woo, W., An, G.B., Kingston, E.J., De Wald, A.T., Smith, D.J., Hill, M.R., 2000. Through-thickness distributions of residual stresses in two extreme heat-input thick welds: a neutron diffraction, contour method and deep hole drilling study. Acta Mater 61, 3564-3574.

Cited by

  1. Weld bead temperature and residual stresses evaluations in multipass dissimilar INCONEL625 and SS316L by GTAW using IR thermography and x-ray diffraction techniques vol.6, pp.9, 2018, https://doi.org/10.1088/2053-1591/ab3298
  2. Residual stress effects on fatigue life prediction using hardness measurements for butt-welded joints made of high strength steels vol.147, pp.None, 2021, https://doi.org/10.1016/j.ijfatigue.2021.106175
  3. Residual stresses in surface layers and coatings vol.2144, pp.1, 2018, https://doi.org/10.1088/1742-6596/2144/1/012011
  4. Residual stresses in surface layers and coatings vol.2144, pp.1, 2018, https://doi.org/10.1088/1742-6596/2144/1/012011