• 문화기술의 융합
• /
• 제8권4호
• /
• pp.407-413
• /
• 2022

본 연구에서는 약 3년간의 장기계측을 바탕으로 공용중인 복층 교량인 상부 도로교의 신축이음 신축량과 하부 철도교의 케이블 장력 간의 상관관계를 입증함으로서 온도변화에 따른 케이블 장력 평가 경험식을 제안하였다. 본 연구에서 제안한 케이블별 장력 평가 경험식을 이용한 장력 예측결과는 진동법을 이용한 장력과 3% 이내로 잘 일치하는 것으로 나타나 공용중인 케이블의 장력 예측 및 평가에 실험적인 기법인 진동법과 함께 적용이 가능할 것으로 판단되었다. 본 연구에서 제안한 신축량 경험식으로 산출한 추정온도를 케이블 경험식에 적용한 결과, 현장시험 진동법 측정결과와 비교시 높은 신뢰수준을 확보할 수 있을 것으로 분석되었다. 따라서 본 연구에서 제안한 추정온도를 반영한 장력 평가 경험식은 향후 기후변화에 따른 케이블의 장력 예측 및 유지관리방안 수립에 활용될 수 있을 것으로 판단된다.

• 해양환경안전학회지
• /
• 제21권3호
• /
• pp.297-302
• /
• 2015

To prevent cargo accidents by repeated loads, a continuous monitoring for securing rope or additional safety measures are needed, but most of prevention measures have been conducted only by operator's own experience not a quantitative assessment. Hence, the Load-Displacement curve and approximation formula of securing rope were drawn in this research for a quantitative assessment and simplified measurement on a tension of securing rope using a tensiometer. Moreover, a com parison was conducted between m easuring tension and calculated tension on securing rope with portable tensiometer, 'Load-Displacement' approximation formula. The calculated tension of securing rope is obtained 153.3kfg using the formula and that result has not much difference with initial tension 150.0kgf. Lastly, an analysis of the characteristics of various ropes was suggested to enhance the reliability about quantitative assessment of securing rope's tension through further research.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.132-142
• /
• 1999

In this paper, a new formula for primary and secondary thrust of metal belt CVT is proposed considering variation of band tension, block compression and active arc for each of the primary and secondary pulleys. For the secondary thrust, effective friction coefficient is introduced considering the effect of flange deflection. Nondimensional primary and secondary thrust of the metal belt CVT by the new formula agree well with the experimental results except for low torque range, $0\;<\;{\lambda}\;<\;0.2$ at speed ration i = 1.0. The new formula can be used in design of the primary and secondary thrusts control system for the metal belt CVT.

• Computers and Concrete
• /
• 제25권3호
• /
• pp.193-204
• /
• 2020

In the study, a new, simple and alternative formula is proposed to calculate numerically crack widths of concrete on a finite element (FE) model. By considering more general tension softening behavior of concrete, the proposed expression is derived irrespective of any tension softening model given in the literature or design codes. The test results of six reinforced concrete (RC) deep beams having different geometrical and material properties selected from a recent existing experimental study of the authors are used to verify the accuracy and reliability of the proposed formula and the created numerical FE models of the specimens. Moreover, the crack width results obtained from the FE models are compared with the test results to see the performance of the proposed formula. The results of the study demonstrate that the proposed formula gives very accurate results in a comparison with the test results. The ratios of errors on the results stay commonly at an acceptable level as well. Consequently, the proposed formula is quite simple, unique, and robust to determine crack widths of RC deep beams on an FE model.

• 대한조선학회논문집
• /
• 제44권5호
• /
• pp.504-508
• /
• 2007

In the case of thin plate blocks, buckling deformation due to longitudinal shrinkage is the most important weld-induced deformation. This paper is concerned with developing the formula to predict the longitudinal shrinkage due to welding, in which mechanical tension effect in welding direction is accounted for. For this purpose, bead on plate welding test has been carried out for the 27 thin plate specimens with varying welding conditions and magnitude of tensile load. Empirical formula of predicting the longitudinal shrinkage has been derived based on the results of welding test, in which effect of mechanical tension is included. The derived formula can be usefully used in predicting the level of tensile load to reduce the longitudinal shrinkage.

• Structural Monitoring and Maintenance
• /
• 제10권4호
• /
• pp.361-379
• /
• 2023

In cable structure maintenance, particularly for cable-stayed bridges, cable safety assessment relies on estimating cable tension. Conventionally, in Japan, cable tension is estimated from the natural frequencies of the cable using the higher-order vibration method. In recent years, dampers have been installed on cables to reduce cable vibrations. Because the higher-order vibration method is a method for damper-free cables, the damper must be removed to measure the natural frequencies of a cable without a damper. However, cables on some cable-stayed bridges have two dampers: one on the girder side and another on the tower side. Notably, removing and reinstalling the damper on the tower side are considerably more time- and labor-intensive. This paper introduces a tension estimation method for cables with two dampers, using natural frequencies. The proposed method was validated through numerical simulation and experiment. In the numerical tests, without measurement error in the natural frequencies, the maximum estimation error among 100 models was 3.3%. With measurement error of 2%, the average estimation error was within 5%, with a maximum error of 9%. The proposed method has high accuracy because the higher-order vibration method for a damper-free cable still has an estimation error of 5%. The experimental verification emphasizes the importance of accurate damper modeling, highlighting potential discrepancies between existing damper design formula and actual damper behavior. By revising the damper formula, the proposed method achieved accurate cable tension estimation, with a maximum estimation error of approximately 10%.

• Journal of the Korean Wood Science and Technology
• /
• 제26권4호
• /
• pp.6-12
• /
• 1998

Test results of domestic softwood lumber were presented to examine the notch effect of beams and compare to present AIJ(Architecture Institute of Japan) formula in notched wood member especially positioned in bottom side (tension side) of a beam. Notched lumber was tested under following condition : each specimen supported simply, and subjected to third-point loading at points of 1/3 of the span length. Notch was located opposite side to loading direction and notch depth were 1/6, 1/4, 1/3 of beam depth. Deflection and load were measured by digital dial guage each in 25kgf increment. Bending test results were as follows; Mpro/Mmax range (proportional and maxium bending moment ratio in notched beam) was 0.5 - 0.65. It was considered that maxium bending moment was about 1.5 times to proportional bending moment in notched beam and showed same tendency in the test result of ordinary wood specimens. AU standard formula for the tension side notch, Mmat = 0.6 ${\times}$ (Zo $\sigma$), the constant 0.6 was suitble for notch ratio(notch depth to beam depth) 1/6, but this ratio for 1/4, and 1/3 was not. So it is preferable to accept smaller value than 0.6 for notch ratio more than 1/3. These experiment results showed critical effect in tension side notched wood beam especially in greater than notch ratio 1.3 of wood beam. From the above results, it is recommened to revise design formula adoptable to domestic wood constructon member with tension side notched member.

• 대한한의학방제학회지
• /
• 제21권1호
• /
• pp.206-212
• /
• 2013

Objectives : The purpose of this study is to report the clinical effects of Dangkisoo-san and acupuncture on a patient with Tension Type headache. Methods : We have given Dangkisoo-san and acupuncture treatment to a patient with Tension Type headache for 8days, and checked changes of symptoms. Main symptoms were numbness and pains in a head and a neck. Results : After treatment, the numbness and pains in a head and a neck were improved considerably. Conclusions : This study shows that Dangkisoo-san and acupuncture are significantly effective in treatment of Tension Type headache.

• Structural Engineering and Mechanics
• /
• 제50권1호
• /
• pp.37-52
• /
• 2014

The accurate determination of cable tension is important to the monitoring of the condition of a cable-stayed bridge. When applying a vibration-based formula to identify the tension of a real cable under sag, stiffness and boundary conditions, the resulting error must not be overlooked. In this work, by resolving the implicit frequency function of a real cable under the above conditions numerically, indirect methods of determining the cable force and a method to calculate the corresponding cable mode frequency are investigated. The error in the tension is studied by numerical simulation, and an empirical error correction formula is presented by fitting the relationship between the cable force error and cable parameters ${\lambda}^2$ and ${\xi}$. A case study on two real cables of the Shanghai Changjiang Bridge shows that employing the method proposed in this paper can increase the accuracy of the determined cable force and reduce the computing time relative to the time required for the finite element model.

• 수산해양기술연구
• /
• 제22권2호
• /
• pp.40-45
• /
• 1986

In this paper, the I-resistance curve of low-carbon steel with 3 mm thickness was investigated for various crack ratios. The experiments were carried out for the center cracked tension (CCT) specimen with about 50 mm width on an instron machine. The plane stress fracture toughness obtained by the Simpson's formula was Ii. = 24.96 kgffmm. Simpson's formula which considers crack growth in obtaining J integral showed more conservative lin than Rice's and Sumpter's. For materials that may be approximated by the Ramberg and Osgood stress strain law, the relevant crack parameters like the J integral, load line displacement are approximately normalized. Crack driving forces in terms of the I integral are computed for low-carbon steel CCT specimen using the above estimation scheme. Comparison of the prediction with actual experimental measurements by Simpson's formula showed good agreement for several different sized specimen.