• Textile Coloration and Finishing
• /
• v.6 no.1
• /
• pp.19-27
• /
• 1994

Mimosa and Quebracho are, in general, tanned with leather skin, finished silk fabrics according to temperature, treatment time, tannin concetration, pH, and studies that relation between tannin weighting and various factors. This makes fundamental study on characteristic of tannin treated fabrics. and the results are as fallows : 1. λ$_{max}$ was found at 278.5nm for Mimosa. 279.5nm for Quebracho. Also a stability was good in standing time and heating. 2. The higher tannin treatment temprature was, the better tannin weighting effect was. But they were slightly decreased at over 8$0^{\circ}C$, and K/S was slowly increased. 3. As tannin treatment time increased, tannin weighting effect increased but they were decreased at over 8$0^{\circ}C$, 90min. 4. As tannin concentration increased, tannin weighting was increased. 5. In tannin weighting effect according to various pH conditions, the it's best range of pH were 3.5~5.5 of Mimosa, 2.5~3.5 of Quebracho.o.

• Journal of Conservation Science
• /
• v.30 no.2
• /
• pp.149-156
• /
• 2014

Low oxygen treatment and heating treatment are used to prevent insects in the field of food science. These eco-friendly control methods can be applied to biological control technique in conservation treatment of organic cultural properties. To evaluate material stability, low-oxygen treatment and low oxygen treatment are applied to wood, pigment, paper and textile that are related to historical wooden buildings. As a result, wood moisture content declined after low oxygen treatment. But decline rate is a little, so it can be expected to turn back original state as time passes. And test result on pigment, paper, textile of chrominance and strength of test materials are stable. But after heating treatment, pigments are separated.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.645-651
• /
• 1997

Tetragonal zirconia polycrystals (TZPs) doped with $Y_{2}O_{3}$ and $Nb_{2}O_{5}$ were prepared by the conventional sintering to enhance fracture toughness and phase stability of TZPs without controlling the grain size. TZP composites were obtained by adding the transformable TZP to the non-transformable TZP in wt%. The monolithic tetragonal $ZrO_2$, same as the composite composition containing 15 wt% transformable TZP, sintered at $1550^{\circ}C$ for 10h in air, exhibited the fracture toughness of 9$MPam^{1/2}$ and no low-and high-temperature degradation at temperatures in the range of 220 to $1000^{\circ}C$ for 100h in air. The corresponding single composition was 90.24 mol% $ZrO_2$-5.31 mol% $Y_{2}O_{3}$-4.75 mol% $Nb_{2}O_{5}$. The microstructure observation revealed that the t-$ZrO_2$ grains grew grandually with sintering time and no microcraking and twinning were observed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.2
• /
• pp.277-284
• /
• 2024

For the high reliability of guidance weapon, it is important to maintain the stable supply voltage for guidance system while the bomb is gliding. However, the DC motor drive for guidance control in the low temperature can lead to the critical voltage drop due to a large inrush current. In this paper, we propose the wing deployment logic design to enhance the guidance system stability. To derive the stable drive logic based on PWM, we controlled the duty cycles for input voltage of DC motor in low temperature. The initial duty cycle was set to 40 % to relieve the inrush current. Moreover, the proper time, which is less than 1 second for controlling duty cycles, was determined by the iterative wing deployments of guidance kit. Finally, the validity of proposed logic was confirmed from the result the maximum voltage drop for the wing deployment was decreased by 23 %.

• The Korean Journal of Rheology
• /
• v.11 no.2
• /
• pp.135-142
• /
• 1999

The effects of 1 wt.% N-benzylpyrazinium hexafluoroantimonate (BPH) as a thermal latent initiator and blend compositions composed of 0, 5, 10, 20 and 40 wt.% of phenol-novolac resin to epoxy resin were investigated in terms of cure kinetics, thermal stabilities and rheological properties. Thermal latent properties of BPH were measured from the conversion as a function of reaction temperature on a dynamic DSC. This cationic BPH system turned out to be an effective thermal latent initiator in the epoxy-phenol curing system. And the increase of phenol-novolac resin concentration led to the decrease in the latent temperature and to the increase of cure activation energy ($E_a$) of the blend system. The thermal stability and activation energy ($E_t$) for decomposition, gel-time and activation energy ($E_c$) for cross-linking from rheometer increased within the composition range of 20~40 wt.% of phenol-novolac resin. This implies that the three-dimensional cross-linking may take place among hydroxyl group within phenol resin, epoxide ring within epoxy resin and BPH.

• Journal of Korean Society of Water and Wastewater
• /
• v.11 no.1
• /
• pp.33-41
• /
• 1997

An attempt was made to enhance anaerobic treatment efficiency by adopting the anaerobic sequencing batch reactor(ASBR) process at a thermophilic temperature. Operational characteristics of the ASBR process were studied using laboratory scale reactors and concentrated organic wastewater composed of soluble starch and essential nutrients. Effects of fill to react ratio (F/R) were examined in the Phase I experiment, where the equivalent hydraulic retention time(HRT) was maintained at 5 days with the influent COD of 10g/L. A continuous stirred tank reactor(CSTR) was operated in parallel as a reference. Treatment efficiency was higher for the ASBRs because of continuous accumulation of volatile suspended solids(VSS) compared to the CSTR. However, the rate of gas production and organic removal per unit VSS in the ASBRs was much lower than the CSTR. This was caused by reduced methane fermentation due to accumulation of volatile acids(VA), especially for the case of low F/R, during the fill period. When the F/R was high, maximum VA was low and the VA decreased in short period. Consequently, more stable operation was possible with higher F/R. Effects of hydraulic loading rate on the efficiency was studied in the Phase II experiment, where the organic loading rate was elevated to 3333mg/L-d with the F/R of 0.12. Reduction of organic removal along with rapid increase of VA was observed and the stability of reaction was seriously impaired, when the influent COD was doubled. However, operation of the ASBR was quite stable, when the hydraulic loading rate was doubled and a cycle time was adjusted to 12 hour. It is essential to avoid rapid accumulation of VA during the fill period in order to maintain operational stability of the ASBR.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.2
• /
• pp.121-127
• /
• 2013

Tritium was attracted with high energy source in neutron fusion energy systems. A number of research was performed in tritium storage materials. The Korea was raised storage and delivery systems (SDS) of international thermonuclear experimental reactor (ITER) research. However, bottles of SDS would be important because of stability. The bottles have a welding zone, this zone will be vulnerable to hydrogen embrittlement. This zone have a high thermodynamic energy and heat deterioration. Therefore bottles were studied about hydrogen embrittlement to retain stability. The heat treatment of hydrogen was carried under pressure-composition-temperature (PCT) apparatus because of checking at real time. And then, mechanical properties were evaluated by tensile test and hardness test. In results of this study, hydrogen atmosphere condition is very important by tensile test and kinetics test. The samples were evaluated, that is more weak hydrogen pressure, increasing temperature and time. This results could be useful in SDS bottle designs.

• Korean Journal of Poultry Science
• /
• v.15 no.1
• /
• pp.39-44
• /
• 1988

This study was undertaken to find out the effect of heating time and temperature, pH and NaCl concentration on heat sensitivity of egg albumen during heat treatment. Sharp increase of the turbidity and rapid decrease of the foaming power were observed when egg albumen was heated at above $60^{\circ}C$. Egg albumen became opaque when it was heated at $60^{\circ}C$ for above 13 minutes or at $65^{\circ}C$ for above 5 minutes. The turbidity was markedly increased at below pH 7 and the foaming power was largely decreased at around pH 4.0 by the heat treatment ($60^{\circ}C$, 5 min). The foam stability was slightly decreased at alkaline pH range by the heat treatment (60t, 5 min). The addition of NaCl up to 0.3M decreased the turbidity. There was no effect of NaCl addition on the foaming power, but the foam stability was decreased by the addition of NaCl at above 0.2M before and after the heat treatment ($60^{\circ}C$, 5 min).

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.168-176
• /
• 2001

The effect of novel N-crotyl-N,N-dimethyl-4-methylanilinium hexafluoroantimonate (CMH) curing agent as a thermal latent initiator on thermal behaviors, rheological properties, and thermal stability of diglycidylether of bisphenol A (DGEBA) epoxy cationic system was investigated. From DSC measurements of DGEBA/CMH system, it was shown that this system exhibits an excellent thermal latent characteristic at a given temperature. The conversion and conversion rate of DGEBA/CMH system increased with increasing the concentration of initiator, due to high activity of CMH. Rheological properties of the system were investigated under isothermal condition using a rheometer The gelation time was obtained from the analysis of storage modulus (G'), loss modulus (G"), and damping factor (tan $\delta$). As a result, the reduction of gelation time was affected by high curing temperature and concentration of CMH, resulting in high degree of network formation in cationic polymerization, due to difference of activity. The thermal stability of the cured epoxy resin was discussed in terms of the activation energy for decomposition and thermal factors determined from TGA measurements.ents.

• Analytical Science and Technology
• /
• v.35 no.5
• /
• pp.212-217
• /
• 2022

In this study, ozone (O₃) samples were prepared for investigating the heterogeneous reactions between O₃ and tropospheric aerosols and were characterized by spectroscopic methods. O₃ generated from an ozone generator was purified by selective adsorption on refrigerated silica gel, followed by transfer to a sample bulb. The amount of UV light (λ = 256 nm) absorbed by O₃ was measured as a function of time at two different temperatures (room temperature and 50 ℃) and under different irradiation conditions. A correlation plot of 1/[O₃] versus time showed that O₃ decomposition follows the 2^nd order reaction rate under a steady-state approximation. The initial concentration of O₃, observed rate constants (k_obs), and the half-life of O₃ in the sample stored at room temperature were determined to be 2.74 [±0.14] × 10¹⁶ molecules·cm^-3, 4.47 [±0.64] × 10^-23 molecules^-1·cm³·s^-1, and 9.5 [±1.4] days, respectively. The evaluation of O₃ stability under various conditions indicated that special care should be taken to prevent the exposure of the O₃ samples to hightemperature environment and/or UV radiation. This study established a protocol for the preparation of highly purified O₃ samples and confirmed that the O₃ samples can be stored for a day after preparation for further experiments.