• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3440-3445
• /
• 2007

For proton exchange membrane fuel cell, it is very important to design the flow channel on separation plate optimally to maximize the current density at same electrochemical reaction surface and reduce the concentration polarization occurred at high current density. In this paper, three dimensional computation model including anode and cathode domain together was developed to examine effects of flow patterns and operation conditions such as humidity and operating temperature on performance of fuel cell. Results show that voltage at counter flow condition is higher than that at coflow condition in parallel and interdigitated flow pattern. And fuel cell with interdigitated flow pattern which has better mass transport by convection flow through gas diffusion layer has higher performance than with parallel flow pattern but its pressure drop is increased such that the trade off between performance and pressure drop should be considered for selection of flow pattern of fuel cell.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.12
• /
• pp.685-690
• /
• 2000

Multiple-lightning impulse currents are a general feature of the lightning ground f=flash. It is therefore necessary for lightning arresters used in power systems to be estimated by applying not only a single-lightning impulse current but also a multiple-lightning impulse currents. This paper presents the effects of multiple-lightning impulse currents on deterioration of ZnO arrester blocks. The multiple-lightning impulse generator which can produce quadruple 8/20$[\mus]$ 5[kA] with separation time of 30~120[ms] is designed and fabricated. The total energy applied to the arrester block at each impulse is about 1,200[J]. In experiment, various parameters such as leakage current component, reference voltage, and temperature are measured with the number of applied impulse current. Also, micro-structure changes of the ZnO blocks after applying the single and the multiple-lightning impulse currents of 200 times are compared. The experimental results indicate that the types of arrester blocks are more vulnerable to deterioration or damage by multiple-lightning impulse currents.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.3
• /
• pp.678-682
• /
• 2010

A doubly tethered chiral stationary phase (CSP) based on (+)-(18-crown-6)-2,3,11,12-tetracarboxylic acid were applied to the liquid chromatographic resolution of racemic tocainide, an antiarrhythmic agent, and its analogues. The chiral recognition efficiency of the doubly tethered CSP for tocainide and its analogues was generally greater than that of the corresponding singly tethered CSP especially in terms of the resolution ($R_S$). The resolution of tocainide and its analogues on the doubly tethered CSP were dependent on the content and the type of the organic and acidic modifiers in aqueous mobile phase and the column temperature. Especially, the retention behaviors of analytes on the doubly tethered CSP with the variation of the content of organic modifier in aqueous mobile phase were opposite to those on the corresponding singly tethered CSP and these opposite retention behaviors were rationalized by the lipophilicity differences of the two CSPs.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1722-1728
• /
• 2012

During the analyzing processes of the compounds, some researchers are puzzled by the analytical signals for some TSNAs (with or without splitting peaks at various pHs and temperatures). In this work, a detailed theoretical study of structural and thermal properties of the $E/Z$ isomers of TSNAs and the corresponding protonated structures was performed using DFT methods. The calculations showed that the $E$ isomers are almost stable than $Z$ isomers, while the $Z$ isomers would be more stable when in protonation. The calculated results predicted the possibility of separation of their $E$ and $Z$ isomer forms and also showed that protonation affects the dipole moment of molecules significantly (0.1-0.5 to 0.7-2.1 Debye). The calculations agreed well with the experiments that the split-up of the HPLC signal for TSNAs into two peaks are very sensitive to the pH and temperature of the mobile-phase.

• Membrane and Water Treatment
• /
• v.1 no.1
• /
• pp.49-60
• /
• 2010

In this study, response surface methodology (RSM) was performed in NF membrane process to evaluate the separation efficiency of membrane in the removal of salt and reactive dye by varying different variables such as pressure, temperature, pH, dye concentration and salt concentration. The significant level of both the main effects and the interaction were observed by analysis of variance (ANOVA) approach. Based on the statistical analysis, the results have provided valuable information on the relationship between these variables and the performances of membrane. The rejection of salt was found to be greatly influenced by pressure, pH and salt concentration whereas the dye rejection was relatively constant in between 96.22 and 99.43% regardless of the changes in the variables. The water flux on the other hand was found to be affected by the pressure and salt concentration. It is also found that the model predictions were in good agreement with the experimental data, indicating the validity of these models in predicting membrane performances prior to the real filtration process.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.94-100
• /
• 2016

Hydrogen production via steam reforming of bio-oil from algal biomass over fast pyrolysis with commercial catalysts was carried out. Aqueous bio-oil obtained by phase separation from a crude oil over fast pyrolysis was used as a reactant and comparison studies for activity over different catalysts (FCR-4-02, POS-7, Cat. A, RUA), reaction temperature, and steam/carbon (S/C) ratios were performed. Experimental results showed that different catalytic activities were observed with different S/C ratios and catalyst composition and the highest hydrogen yield of 70% was obtained with a POS-7 catalyst at a S/C ratio of 10 and 1073 K.

• Journal of Haehwa Medicine
• /
• v.23 no.1
• /
• pp.93-104
• /
• 2014

Glycyrrhizae Radix et Rhizoma has been extensively used by human beings as a medicinal herb as well as natural sweetener. In this study, we performed quantification analysis of three major constituents including liquiritin, glycyrrhizin, and glycyrrhetinic acid in the 70% ethanol extracts of non-processed Glycyrrhizae Radix et Rhizoma and processed Glycyrrhizae Radix et Rhizoma using a high-performance liquid chromatography coupled with photodiode array detector. The analytical column for separation of the 3 constituents used a Gemini C18 column kept at $40^{\circ}C$ by the gradient elution of two mobile phase. The amounts of liquiritin, glycyrrhizin, and glycyrrhetinic acid in non-processed Glycyrrhizae Radix et Rhizoma were 2.57%, 3.52%, and not detected. After processing by roasting, the best roasting temperature and time of iquiritin, glycyrrhizin, and glycyrrhetinic acid were $160^{\circ}C$-15 min (2.46%), $160^{\circ}C$-15 min (3.67%), and $240^{\circ}C$-15 min (0.76%), respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.228-231
• /
• 2005

In this paper, we present reusable quartz master fabricated by electron-beam lithography and dry etching process of quartz, and results of injection molding based on the reusable quartz master for the manufacturing of nano-scale information media. Since patterned structures of photoresist can be easily damaged by separation (demolding) process of nickel stamper and master, a master with photoresist cannot be reused in stamper fabrication process. In this work, we have made it possible of the repeated use of master by directly patterning on quart in nickel stamper fabrication process. We have designed and fabricated four different specimens including 100nm, 140nm 200nm and 400nm pit patterns. In addition, both intaglio and embossed carving patterns are fabricated for each specimen. In the preliminary test of injection molding, we have fabricated polycarbonate patterns with varying mold temperature. We have experimentally verified the fabrication process of the reusable quart master and possibility of quartz master as direct stamper.

• Corrosion Science and Technology
• /
• v.7 no.2
• /
• pp.69-76
• /
• 2008

Common methods for large scale hydrogen production, such as steam reforming and coal gasification, also involve production of carbonaceous gases. It is therefore necessary to handle process gas streams involving various mixtures of hydrocarbons, $H_2$, $H_2O$, CO and $CO_2$ at moderate to high temperatures. These gases pose a variety of corrosion threats to the alloys used in plant construction. Carbon is a particularly aggressive corrodent, leading to carburisation and, at high carbon activities, to metal dusting. The behaviour of commercial heat resisting alloys 602CA and 800, together with that of 304 stainless steel, was studied during thermal cycling in $CO/CO_2$ at $650-750^{\circ}C$, and also in $CO/H_2/H_2O$ at $680^{\circ}C$. Thermal cycling caused repeated scale separation, which accelerated chromium depletion from the alloy subsurface regions. The $CO/H_2/H_2O$ gas, with $a_C=2.9$ and $p(O_2)=5\times10^{-23}$ atm, caused relatively rapid metal dusting, accompanied by some internal carburisation. In contrast, the $CO/CO_2$ gas, with $a_C=7$ and $p(O_2)=10^{-23}-10^{-24}$ atm caused internal precipitation in all three alloys, but no dusting. Inward diffusion of oxygen led to in situ oxidation of internal carbides. The very different reaction morphologies produced by the two gas mixtures are discussed in terms of competing gas-alloy reaction steps.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.1
• /
• pp.40-49
• /
• 2001

We have developed a repeatable process of forming uniform, small-size and high-density self-assembled Si nano-crystals. The Si nano-crystals were fabricated in a conventional LPCVD (low pressure chemical vapor deposition) reactor at $620^{\circ}c$ for 15 sec. The nano-crystals were spherical shaped with about 4.5 nm in diameter and density of $5{\times}l0^{11}/$\textrm{cm}^2$. More uniform dots were fabricated on nitride film than on oxide film. To take advantage of the above-mentioned characteristics of nitride film while keeping the high interface quality between the tunneling dielectrics and the Si substrate, nitride-oxide tunneling dielectrics is proposed in n-channel device. For the first time, the single electron effect at room temperature, which shows a saturation of threshold voltage in a range of gate voltages with a periodicity of ${\Delta}Ｖ_{GS}\;{\approx}\;1.7{\;}V$, corresponding to single and multiple electron storage is reported. The feasibility of p-channel nano-crystal memory with thin oxide in direct tunneling regime is demonstrated. The programming mechanisms of p-channel nano-crystal memory were investigated by charge separation technique. For small gate programming voltage, hole tunneling component from inversion layer is dominant. However, valence band electron tunneling component from the valence band in the nano-crystal becomes dominant for large gate voltage. Finally, the comparison of retention between programmed holes and electrons shows that holes have longer retention time.