• 펄프종이기술
• /
• 제34권4호
• /
• pp.16-21
• /
• 2002

It was observed that drying temperature and curing time in the paper coating process as well as Tg of the latex used as a binder, greatly affected the properties of the coated paper such as roughness, paper and print gloss, K & N ink drop, and ink set-off. The higher drying temperature induced faster water evaporation and change in binding density, which caused an increase in paper roughness, ink gloss and ink set-off, but decrease in paper gloss and K & N ink drop. The increased curing time promoted latex filming and redistribution of the binder in coating layer. This increased pick strength and ink gloss, but decreased ink trapping. Finally, the higher Tg of the latex showed the wider changing range of these properties.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 학술대회 논문집
• /
• pp.131-135
• /
• 2004

The molecules of the substance absorbing a light obtains the radiant energy to the wavelength of the light to make thermal reactions or photochemical reactions. Specially, thermal reactions by infrared radiation brings about physical damage by temperature rise process or temperature drop process of the material. In this study, a measuring system was set up to measure the temperature rise and temperature drop of each sample by infrared radiation from light source. And a physical demage of samples by infrared radiation were measured using the measuring system.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.852-859
• /
• 2003

R407C is considered as an alternative refrigerant of R22 for air conditioners. An experiment was carried out to investigate the characteristics of the evaporation heat transfer and pressure drop for refrigerant R407C flowing in a fin-and-tube heat exchanger used for commercial air-conditioning unit. The experimental data were useful in analyze the effects of the temperature glide and superheat for R407C. Test were conducted at the conditions of inlet refrigerant evaporation temperature of 7$^{\circ}C$, inlet air relative humidity of 50%, and refrigerant mass fluxes varying from 150 to 250 kg/m$^2$s. Representative results show that the heat exchanger performance for R407C evaporation is significantly affected by the change of the flow pattern from two-phase to super-heated vapor flow.

• 한국군사과학기술학회지
• /
• 제3권2호
• /
• pp.53-60
• /
• 2000

Organic brake materials are installed in the braking system of korean model combat vehicles. Since the binder resin is decomposed in high temperature region, it may possible to drop the friction force which makes the vehicle stop within the desired distance. This study analyses the braking performance of the brake materials in high temperature region by using the pin-on-disk type friction tester. It is observed radical drop of friction coefficients and rapid increase of wear amounts from the transition temperature. It is due to the formation of oxide layer on the friction surface.

• 제어로봇시스템학회논문지
• /
• 제12권12호
• /
• pp.1249-1255
• /
• 2006

This paper presents a constant power control logic for perfect starting a microtubine in vehicle. Under extremely low temperature, performance of the start-up system is severely dropped than that of room temperature because of increasing of load of mechanical parts including engine core and drop of the lead-acid battery capacity. Unfortunately, performance drop of lead-acid battery makes severe problems that cause a malfunction of fuel and lubrication system and power fail of digital devices. So we propose the new start-up logic by constant output power control of lead-acid battery using PWM inverter controller for preventing above problems and keeping good performance of start-up system for microturbine. Also, we prove usefulness of new start-up logic through experimental results under $-32^{\circ}C$ ambient temperature.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 춘계 학술논문 발표대회
• /
• pp.71-72
• /
• 2013

This study investigates the effect of the diameters of reinforcement bars located in an euro-form before placing concrete in a cold weather condition. The diameters of reinforcement bars with 13 mm, 19 mm, 25 mm and 32 mm were prepared for the experimental tests. Results showed that the larger the size of the diameter of the bars, the higher were the temperature drop. However, this study found that its effect on the temperature drop of the bars was insignificant.

• 설비공학논문집
• /
• 제16권1호
• /
• pp.42-53
• /
• 2004

An experimental study on the refrigerant-side pressure drop of slit fin-tube heat exchanger has been carried out. A comparison was made between the predictions of previously proposed empirical correlations and experimental data for the pressure drop on design conditions of condenser in micro-fin tube for R22 and its alternatives, R407C (R32/125/134a, 23/25/52 wt.％) and R410A (R32/125, 50/50 wt.％). Experiments were carried out under the conditions of inlet refrigerant temperature of 6$0^{\circ}C$ and mass fluxes varying from 150 to 250 kg/$m^2$s for R22, R407C and R410A. The inlet air conditions are dry bulb temperature of 35$^{\circ}C$, relative humidity of 40% and air velocity varying from 0.68 to 1.43 m/s. Experiments show that pressure drop for R410A and R407C were 17.8∼20.2％ and 5∼6.8％ lower than those of R22 respectively for the degree of subcooling of 5$^{\circ}C$. For the mass fluxes of 200∼250 kg/$m^2$s, the deviation between the experimental and predicted values for the pressure drop was less than $\pm$20％ for R22, R407C and R410A.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.189-194
• /
• 2005

The evaporation heat transfer and pressure drop of $CO_2$ in a small diameter tube was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator(test section). The test section was made of a horizontal stainless steel tube with the inner diameter of 4.57 mm, and length of 4 m. The experiments were conducted at mass flux of 200 to 700 $kg/m^2s$, saturation temperature of $0^{\circ}C$ to $20^{\circ}C$, and heat flux of 10 to 20 $kW/m^2$ . The test results showed the evaporation heat transfer of $CO_2$ has great effect on more nucleate boiling than convective boiling. The evaporation heat transfer coefficients of $CO_2$ are highly dependent on the vapor quality, heat flux and saturation temperature. The evaporation pressure drop of C02 are highly dependent on the mass flux. In comparison with test results and existing correlations, correlations failed to predict the evaporation heat transfer coefficient and pressure drop of $CO_2$, therefore, it is necessary to develop reliable and accurate predictions determining the evaporation heat transfer coefficient and friction pressure drop of $CO_2$ in a horizontal tube.

• 생물환경조절학회지
• /
• 제3권1호
• /
• pp.58-65
• /
• 1994

본 시험은 하절기 경제성을 고려한 효율적인 온도하강방법을 구명하고자 차광재료, fog system, 송풍등 복합적 온도하강처리에 따른 비닐하우스의 기상환경변화를 조사하여 다음과 같은 결과를 얻었다. 1. 중형하우스에서 온도하강방법에 따른 환경특성은 처리에 따라 하우스의 고온화를 상당히 효율적으로 억제하였다. 7월31일 하우스냉방처리에 따른 기온의 일중변화를 경시적으로 보면 수분의 증발잠력능력을 이용한 fog system과 은색차광 및 송풍을 혼합하여 처리할 경우 기온과 지온은 외기온에 비하여 최고 각각 1$0^{\circ}C$, 4$^{\circ}C$정도 온도하강효과가 있었으며 그 다음은 은색차광＋fog system, 은색차광＋송풍, 흑색차광＋송풍구 순이였다. 2. 하절기 가장 온도가 높은 시기인 7월20일부터 8월21일까지 하우스냉방처리에 따른 온도하강 효과를 보면 최고기온은 시험처리에 따라 온도차가 인정되며 은색차광＋fog system＋송풍구의 지상, 지표면기온은 외기온에 비하여 각각 약 8$^{\circ}C$, 7$^{\circ}C$정도 온도하강 효과가 있었다. 3. 은색차광＋송풍구와 흑색차광＋송풍구의 일사량은 청명한날 외기일사량에 비하여 각각 약 29.3%, 32.5%이였으며 흐린 날은 각각 약 27.4%, 31.8%이였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1388-1390
• /
• 1995

The characteristic of dielectric breakdown in solid insulating material dominates the reliability and safety of power equipment and affects directly to its life. In this point of view, the thickness and temperature dependence of dielectric breakdown strength and mechanism of dielectric breakdown in low density polyethylene which has been employed widely as insulating material have been technically reviewed by examinations of thermal property. The dielectric breakdown strength depending on its thickness was measured 2.6[MV/cm] at the thickness of 20[${\mu}m$] and 1.9[MV/cm] at the thickness of 75[${\mu}m$] based on ambient temperature of 30[$^{\circ}C$]. It is shown the temperature dependence that dielectric breakdown strength decreases in linear as the thickness increases. The dielectric breakdown strength depending on temperature was measured 2.6[MV/cm] at the temperature of 30[$^{\circ}C$], 1.6[MV/cm] at 60[$^{\circ}C$] and 1.3[MV/cm] at 90[$^{\circ}C$] based on the thickness of 20[${\mu}m$]. As the ambient temperature increases, the temperature dependence is shown that a very large drop is occurred up to temperature of 60[$^{\circ}C$] and a very small drop is discovered over 60[$^{\circ}C$].