• 한국미생물·생명공학회지
• /
• 제13권1호
• /
• pp.33-39
• /
• 1985

The effects of initial concentration, flow rate, and recycle ratio on the removal efficiency of phenol were studied in a tapered fluidized bed reactor packed with activated carbon which was attached with Candida tropicalis. The optimum conditions of Candida tropicalis were showed that pH was 7.0 and temperature was $30^{\circ}C$, and the specific growth rate of Candida tropicalis was satisfied with the Monod equation up to 500 mg/L of phenol, and beyond it the inhibition of substrate was found. According to the increases of initial concentration and flow rate, the removal efficiency was decreased, as the recycle ratio was increased, the removal efficiency was increased. In the case of flow rate of 10mL/sec and the recycle ratio of 2, the removal efficiency was 90% above for the all of initial concentration. The removal rate of phenol was the first order reaction in this system, and the rate equation of reaction was as follows.

• 한국전산구조공학회논문집
• /
• 제19권2호
• /
• pp.139-150
• /
• 2006

ILM(incremental launching method) 교량공법은 품질확보에 효과적인 프리스트레스트 콘크리트 교량공법으로 인정받고 있다. 이 공법에 의해 시공되는 교량의 상부단면은 시공 중에 지간의 중앙부와 지점부에 일시적이나마 모두 위치하게 된다. 따라서 단면들은 자중에 의해 발생되는 최대 정 모멘트와 최대 부 모멘트, 그리고 최대 전단력을 모두 경험하게 되는 구조적 특성을 가지고 있다. 한편, 압출하는 동안 발생하는 높은 일시적 응력을 최소화하기 위해 일반적으로 압출추진코가 이용되고 있다. 그리고 상부단면에 발생하는 이 일시적인 응력의 크기는 압출추진코의 특성에 따라 달라진다. 본 연구에서는 압출 중 상부단면에 발생하는 단면력의 크기를 쉽고, 빠르게 검토할 수 있는 해석식을 유도하였다. 개발된 해석식에서 고려할 수 있는 매개변수로는 압출추진코와 상부단면과의 지간 길이비와 중량비 그리고 강성비를 택하였다 특히, 개발된 해석식에서는 변단면인 압출추진코의 단면형상과 다이아플램을 고려할 수 있다. 또한, 설계변수들에 대한 민감도 해석을 통하여 압출추진코와 상부단면의 상호작용에 미치는 매개변수들의 영향을 분석하였다.

• 대한토목학회논문집
• /
• 제11권4호
• /
• pp.17-26
• /
• 1991

이 논문(論文)은 단순지지(單純支持) 변단면(變斷面) 기둥의 임계하중(臨界荷重) 및 후좌굴(後挫屈) 거동(擧動)에 관한 연구(硏究)이다. 이 논문(論文)에서는 변단면(變斷面)을 갖는 후좌굴(後挫屈) 기둥의 정확탄성곡선(正確彈性曲線)을 지배(支配)하는 미분방정식(微分方程式)을 3차이론(次理論)에 의(依)하여 유도(誘導)하고, 이 미분방정식(微分方程式)을 Runge-Kutta method와 Regula-Falsi method를 이용하여 임계하중(臨界荷重)과 후좌굴(後挫屈) 기둥의 정확탄성곡선(正確彈性曲線)을 산출(算出)하였다. 실제(實際)의 수치해석(數値解析) 예(例)에서는 변화(變化)높이 구형단면(矩形斷面), 변화폭(變化幅) 구형단면(矩形斷面), 정방형단면(正方形斷面)/원형단면(圓形斷面)의 3가지 단면형상(斷面形狀)에 대하여 수치해석(數値解析)하였다. 수치해석(數値解析)의 결과(結果)로, 하중(荷重)-처짐의 평형경로(平衡經路), 후좌굴(後挫屈) 기둥의 정확탄성곡선(正確彈性曲線), 임계하중(臨界荷重)-단면화(斷面化) 사이의 관계(關係)를 그림에 나타내었다. 또한 단면형상계수(斷面形狀係數)가 임계하중(臨界荷重)과 후좌굴(後挫屈) 거동(擧動)에 미치는 영향(影響)을 분석(分析)하였다.

• 한국소음진동공학회논문집
• /
• 제11권5호
• /
• pp.89-100
• /
• 2001

The Ritz method Is applied In a three-dimensional (3-D) analysis to obtain accurate frequencies for thick. linearly tapered. annular plates. The method is formulated for annular plates haying any combination of free or fixed boundaries at both Inner and outer edges. Admissible functions for the three displacement components are chosen as trigonometric functions in the circumferential co-ordinate. and a1gebraic polynomials in the radial and thickness co-ordinates. Upper bound convergence of the non-dimensional frequencies to the exact values within at least four significant figures is demonstrated. Comparisons of results for annular plates with linearly varying thickness are made with ones obtained by others using 2-D classical thin place theory. Extensive and accurate ( four significant figures ) frequencies are presented 7or completely free. thick, linearly tapered annular plates haying ratios of average place thickness to difference between outer radius (a) and inner radius (b) radios (h$_{m}$/L) of 0.1 and 0.2 for b/L=0.2 and 0.5. All 3-D modes are included in the analyses : e.g., flexural, thickness-shear. In-plane stretching, and torsional. Because frequency data liven is exact 7o a\ulcorner least four digits. It is benchmark data against which the results from other methods (e.g.. 2-D 7hick plate theory, finite element methods. finite difference methods) and may be compared. Throughout this work, Poisson\`s ratio $\upsilon$ is fixed at 0.3 for numerical calculations.s.

• 한국소음진동공학회논문집
• /
• 제21권8호
• /
• pp.698-707
• /
• 2011

이 연구는 유한요소법을 이용하여 집중질량을 갖고 비균질한 지반에 놓은 변단변 후판 구조물에 대한 동적 안정해석이다. 해석을 위하여 유한요소법을 이용하여 해당구조물의 고유진동수와 좌굴하중을 구하여 기존해와 비교하여 프로그램을 검증하였다. 비균질 Pasternak 지반에 놓인 변단면으로 집중질량을 갖는후판의 동적안정 해석을 통하여 판의 불안정 영역이 결정된다. 무차원 Winkler 지반강성은 100, 1000을 적용하였고, 무차원 전단지반강성은 5로 하였다. 그리고 변단면율은 0.25, 1.0, 집중질량비는 0.25, 1.0 그리고 면내응력은 $0.4{\sigma}_{cr}$을 적용하여 해석하였다.

• Smart Structures and Systems
• /
• 제19권3호
• /
• pp.309-322
• /
• 2017

In this paper, the buckling, and free vibration analysis of tapered functionally graded carbon nanotube reinforced composite (FG-CNTRC) micro Reddy beam under longitudinal magnetic field using finite element method (FEM) is investigated. It is noted that the material properties of matrix is considered as Poly methyl methacrylate (PMMA). Using Hamilton's principle, the governing equations of motion are derived by applying a modified strain gradient theory and the rule of mixture approach for micro-composite beam. Micro-composite beam are subjected to longitudinal magnetic field. Then, using the FEM, the critical buckling load, and natural frequency of micro-composite Reddy beam is solved. Also, the influences of various parameters including ${\alpha}$ and ${\beta}$ (the constant coefficients to control the thickness), three material length scale parameters, aspect ratio, different boundary conditions, and various distributions of CNT such as uniform distribution (UD), unsymmetrical functionally graded distribution of CNT (USFG) and symmetrically linear distribution of CNT (SFG) on the critical buckling load and non-dimensional natural frequency are obtained. It can be seen that the non-dimensional natural frequency and critical buckling load decreases with increasing of ${\beta}$ for UD, USFG and SFG micro-composite beam and vice versa for ${\alpha}$. Also, it is shown that at the specified value of ${\alpha}$ and ${\beta}$, the dimensionless natural frequency and critical buckling load for SGT beam is more than for the other state. Moreover, it can be observed from the results that employing magnetic field in longitudinal direction of the micro-composite beam increases the natural frequency and critical buckling load. On the other hands, by increasing the imposed magnetic field significantly increases the stability of the system that can behave as an actuator.

• Hip & pelvis
• /
• 제35권2호
• /
• pp.88-98
• /
• 2023

Purpose: The objectives of this study were to examine the prevalence and risk factors for development of periprosthetic occult femoral fractures during primary cementless total hip arthroplasty (THA) and to assess the clinical consequences of these fractures. Materials and Methods: A total of 199 hips were examined. Periprosthetic occult femoral fractures were defined as fractures not detected intraoperatively and on postoperative radiographs, but only observed on postoperative computed tomography (CT). Clinical, surgical, and radiographic analysis of variables was performed for identification of risk factors for periprosthetic occult femoral fractures. A comparison of stem subsidence, stem alignment, and thigh pain between the occult fracture group and the non-fracture group was also performed. Results: Periprosthetic occult femoral fractures were detected during the operation in 21 (10.6%) of 199 hips. Of eight hips with periprosthetic occult femoral fractures that were detected around the lesser trochanter, concurrent periprosthetic occult femoral fractures located at different levels were detected in six hips (75.0%). Only the female sex showed significant association with an increased risk of periprosthetic occult femoral fractures (odds ratio for males, 0.38; 95% confidence interval, 0.15-1.01; P=0.04). A significant difference in the incidence of thigh pain was observed between the occult fracture group and the non-fracture group (P<0.05). Conclusion: Occurrence of periprosthetic occult femoral fractures is relatively common during primary THA using tapered wedge stems. We recommend CT referral for female patients who report unexplained early postoperative thigh pain or developed periprosthetic intraoperative femoral fractures around the lesser trochanter during primary THA using tapered wedge stems.

• 한국안전학회지
• /
• 제12권4호
• /
• pp.114-121
• /
• 1997

Helical anchors are foundation structure that designed to resist uplift loads are installed by applying in load to shaft while rotating it into the ground. These can be a cost effective means of proving tension anchorage for foundation where soil conditions permit their installation because of ease of installation. At present time, tapered helical anchors are commonly used to carry uplift loads. The uplift capacity includes the following factors : the height of overburden above the top helix, the resistant along a cylinder, the weight of the soil in the cylinder and suction force. In order to make clear behavior characteristics of helical anchors with pullout, model tests were conducted with respect to various embedment depth, space of helix, shape of helix. Based on the experimental study, the following conclusions are drawn. 1) The uplift capacity of multi helical anchors increase with embedment ratio of anchors The increase is smooth after critical uplift capacity. 2) Critical breakout factors and critical embedment ratio of multi helical anchor exist 7∼8, 4∼6 respectively. 3) Variation of uplift capacity with helix spaces show down after S/D=5. 4) Critical breakout factors of helical anchor in the laboratory test are similar to Das's theory.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1991년도 가을 학술발표회 논문집
• /
• pp.75-80
• /
• 1991

The purpose of this study is to ascertain the robustness of p-version model with hierarchic intergrals of Legendre shape functions in various applications including plane stress/strain, axisymmetric and shell problems. The most important symptoms of accuracy failure in modern finite elements are spurious mechanisms and a phenomenon known as locking which are exhibited for incompressible materials and irregular shapes which contain aspect ratios(R/t, a/b), tapered ratio(d/b), and skewness. The condition numbers and energy norms are used to estimate numerical errors, convergence characteristics and algorithmic efficiencies for verifying the aforementioned symptoms of accuracy failure. Numerical results from p-version models are compared wi th those from NASTRAN, SAP90, and Cheung's hybrid elements.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.512-517
• /
• 1993

The cold rolled strip meets continuously rising demands on the less deviation of thickness at the width direction of their rolled products. Especially, the special interest has been to find the methods to reduce the edge drop which influences seriously on the yield losses and the quality of the rolled products. In this study, the influence of hot coils on the thickness profile of cold rolled strip was analyzed. For obtainint the tapered work roll shig\ft conditions, the thermal crown and the flattening between the work roll and the strip were calculated, and the main parameters which have mostly effects on the edge drop were simulated. Also the obtained conditions from the simulation were applied to Tandem Cold Rolling Mill to investigate the change of the edge drop and the crown ratio depending on the amount of work roll taper and the length of contact of taper. The results of the application led to better thickness profile than conventional one.