• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6A
• /
• pp.425-432
• /
• 2003

In this paper, we designed a multi-carrier digital transmitter for CDMA base-station using a direct conversion scheme and verified the performance through circuit simulations. We examined a new technology required to design a multi-carrier transmitter, then designed and simulated a multi-carrier digital transmitter. ADS (Advanced Design System), RF simulation S/W of Agilent Technologies, was used for designing and simulating the multi-carrier digital transmitter. First, we simulated a digital block and an analog block separately, then performed a co-simulation for entire system. From the results, the final analog outputs of the designed multi-carrier digital transmitter met the spectrum mask characteristics of IS-97 & 3G TS 25.104 standard requirements. It means that proposed scheme could be applied to implement a multi-carrier digital transmitter for CDMA base-station. Therefore, proposed multi-carrier digital transmitter using a direct conversion scheme can accomplish cost-reduction and improvements of technology in the next CDMA base-station.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.3
• /
• pp.221-228
• /
• 2011

This paper describes 250-Mb/s fiber optic transmitter and receiver ICs for plastic optical fiber applications using a$ 0.18-{\mu}m$ CMOS technology. Simple signal and light detection schemes are introduced for power reduction in sleep mode. The transmitter converts non-return-to-zero digital data into 650-nm visible-red light signal and the receiver recovers the digital data from the incident light signal through up to 50-m plastic optical fiber. The transmitter and receiver ICs occupy only 0.62 $mm^2$ of area including electrostatic discharge protection diodes and bonding pads. The transmitter IC consumes 23 mA with 20 mA of LED driving currents, and the receiver IC consumes 16 mA with 4 mA of output driving currents at 250 Mb/s of data rate from a 3.3-V supply in active mode. In sleep mode, the transmitter and receiver ICs consume only 25 ${\mu}A$ and 40 ${\mu}A$, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.282-291
• /
• 2010

This paper presents a full-CMOS transmitter and receiver for VDSL2 systems. The transmitter part consists of the low-pass filter, programmable gain amplifier (PGA) and 14-bit DAC. The receiver part consists of the low-pass filter, variable gain amplifier (VGA), and 13-bit ADC. The low pass filter and PGA are designed to support the variable data rate. The RC bank sharing architecture for the low pass filter has reduced the chip size significantly. And, the 80 Msps, high resolution DAC and ADC are integrated to guarantee the SNR. Also, the transmitter and receiver are designed to have a wide dynamic range and gain control range because the signal from the VDSL2 line is variable depending on the distance. The chip is implemented in 0.25 ${\mu}m$ CMOS technology and the die area is 5 mm $\times$ 5 mm. The spurious free dynamic range (SFDR) and SNR of the transmitter and receiver are 67.5 dB and 41 dB, respectively. The power consumption of the transmitter and receiver are 160 mW and 250 mW from the supply voltage of 2.5 V, respectively.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.4
• /
• pp.326-334
• /
• 2016

In this paper for developing and implementing the realtime HD level video streaming transmitter which is operated on the multi-platform in all network and client environment compared to the exist video live streaming transmitter. We design the realtime HD level video streaming transmitter supporting the multi-platform using the TMS320DM386 video processor of T.I company and then porting the Linux kernel 2.6.29 and implementing the RTSP(Real Time Streaming Protocol)/RTP(Real Time Transport Protocol), HLS(Http Live Streaming), RTMP(Real Time Messaging Protocol) that can support the multi-platform of video stream protocol of the received equipments (smart phone, tablet PC, notebook etc.). For proving the performance of developed video streaming transmitter, we make the testing environment for testing the performance of streaming transmitter using the notebook, iPad, android Phone, and then analysis the received video in the client displayer. In this paper, we suggest the developed the Realtime HD(High Definition) level Video Streaming transmitter performance data values higher than the exist products.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1841-1848
• /
• 2010

Electric railway system consist of rolling stock, track, signal and streetcar line system. ATP(Automatic Train Protection) system in railway signaling system is the important one grasping the position and velocity of a train. The wayside transmitter of ATP system is installed between rails. Recently, the research about increasing train speed has been developed in total departments of the railroad systems. The study on the information transmission between on-board transmitter and wayside transmitter is required for increasing the train speed in the ATP system. When the train speed is increased as to same transmissi on distance, the problem on information transmission occurs because the transmission time is decreased. In case that the transmission distance is extended, the transmission time is decreased with respect to the train speed. Therefore, we have to define the standard magnetic intensity as to the train speed in order to transmit correctly telegram. In this paper, the transmission distance for the telegram is suggested on the basis of the train speed. Also, the standard magnetic intensity from the wayside transmitter to on-board transmitter is proposed by using transmission distance regarding the train speed in the ERTMS/ETCS system by using Matlab program.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.121-130
• /
• 2005

In this paper, we designed and fabricated the VHF wireless transmitter for air traffic control. Fundamental performance of the investigated wireless transmitter is designed and fabricated to satisfy existing commercial wireless transmitter specification for air traffic control. 25 W and 50 W of output power can be generated by changing the power amplification part only. It is based on transmitting voice communication using AM modulation. Investigated wireless transmitter for air traffic control consists of four module parts: power supply, control, low power transmission and power amplification. We designed 1W transmitter to operate without power amplification part. It can be used properly in a basic component of CNS/ATM.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.476-481
• /
• 2009

In this paper, we propose a visible light road-to-vehicle communication system at intersection as one of ITS technique. In this system, the communication between vehicle and a LED traffic light is approached using LED traffic light as the transmitter, and on-vehicle high-speed camera as the receiver. The LEDs in the transmitter are emitted with 500Hz and those emitting LEDs are captured by a high-speed camera for making communication. The images from the high-speed camera are processed to get luminance value of each LED in the transmitter. For this purpose, first transmitter should be found, then it should be tracked for each frame, and the luminance value of each LED in the transmitter should be captured. In our previous work, transmitter was found by getting the subtraction of two consecutive frames. In this paper, we mainly introduce an algorithm to detect the found transmitter in consecutive frames. Experimental results using appropriate images showed the effectiveness of the proposal

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.691-706
• /
• 2008

ATP(Automatic Train Protection) system in railway signaling system is the important one grasping the position and velocity of a train. The wayside transmitter of ATP system is installed between rails. In concrete slab track, the signal current using wayside transmitter of ATP system is influenced by reinforcing bars. The magnetic coupling between reinforcing bars and wayside transmitter of ATP system as a filter makes an input current distorted. So, it makes an alternating current signal with a desirable size not transmit to on-board system of a train. Way to decrease the distortion of an input current signal frequency is to avoid maximum induction current frequency. And the induction phenomenon between reinforcing bars insulated and wayside transmitter of ATP system does not occur. In this paper, we represent the model about wayside transmitter of ATP system and reinforcing bars on the concrete slab tracks, and calculated the parameters demanded for the model. Also, we demonstrated it through the Maxwell program. Furthermore, we calculated impedance on wayside transmitter used in KVB system and ERTMS/ETCS system which are a kind of ATP system, frequency response of induction current, using the Matlab, and demonstrated the validity of it, using the PSpice program.

• International Journal of Railway
• /
• v.4 no.1
• /
• pp.12-18
• /
• 2011

The ATS system is used to provide wayside signaling. Currently, the oscillation frequency is set at 78[kHz] in the normal state. As the on-board receiver crosses over the wayside transmitter, the oscillation frequency is changed by capacitors of the wayside transmitter in a manner dependent on the train speed. As the oscillation frequency is changed, the waveform is modified in the wayside transmitter as well as in the on-board receiver. When there are other signal systems such as a ATO system present near the wayside transmitter, frequency interference occurs. This phenomenon arises since other signals or communication frequencies present will be included in the waveform. Trains often stop due to these other frequencies included in the waveform. In this paper, a model of the interaction between the wayside transmitter and on-board receiver is suggested and frequency response in the wayside transmitter and on-board receiver in the presence of the other signals are estimated by the coupling coefficient. Also, the coupling coefficients are estimated, and the optimal value is proposed.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.4
• /
• pp.612-619
• /
• 1990

In this paper, a design method of optical FSK transmitter is described using LD-FM circuit model. In the design of optical FSK transmitter, an optimum bias current was chosen using LD-FM circuit model, and an unequalized FM transfer function was determined at this current. The equalizers that can make this transfer function uniform were designed by use of a simple passive network. For the designed optical FSK transmitter, the pulse-transient and small-signal frequency-deviation responses were simulated and discussed.