• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.290-293
• /
• 2003

Ohmic contact characteristics of Al ion implanted n-type SiC wafer were investigated. Al ions implanted with high dose to obtain the final concentration of $5{\times}10^{19}/cm^3$, then annealed at high temperature. Firstly, B ion ion implanted p-well region were formed which is needed for fabrication of SiC devices such as DIMOSFET and un diode. Secondly, Al implanted high dose region for ohmic contact were formed. After ion implantation, the samples were annealed at high temperature up to $1600^{\circ}C\;and\;1700^{\circ}C$ for 30 min in order to activate the implanted ions electrically. Both the inear TLM and circular TLM method were used for characterization. Ni/Ti metal layer was used for contact metal which is widely used in fabrication of ohmic contacts for n-type SiC. The metal layer was deposited by using RF sputtering and rapid thermal annealed at $950^{\circ}C$ for 90sec. Good ohmic contact characteristics could be obtained regardless of measuring methods. The measured specific contact resistivity for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$ were $1.8{\times}10^{-3}{\Omega}cm^2$, $5.6{\times}10^{-5}{\Omega}cm^2$, respectively. Using the same metal and same process of the ohmic contacts in n-type SiC, it is found possible to make a good ohmic contacts to p-type SiC. It is very helpful for fabricating a integrated SiC devices. In addition, we obtained that the ratio of the electrically activated ions to the implanted Al ions were 10% and 60% for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$, respectively.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.511-524
• /
• 2005

In this paper, we propose a novel hardware architecture for an intra-prediction, integer transform, quantization, inverse integer transform, inverse quantization, and mode decision module for the macroblock engine of a new video coding standard, H.264. To reduce the cycle of intra prediction, transform/quantization, and inverse quantization/inverse transform of H.264, a reduction method for cycle overhead in the case of I16MB mode is proposed. This method can process one macroblock for 927 cycles for all cases of macroblock type by processing $4{\times}4$ Hadamard transform and quantization during $16{\times}16$ prediction. This module was designed using Verilog Hardware Description Language (HDL) and operates with a 54 MHz clock using the Hynix $0.35 {\mu}m$ TLM (triple layer metal) library.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.403-406
• /
• 2009

Recently, electricity is essential for human lives. Modem people take cultural benefits due to the development of the electric power system and the spread of the high tech-electric appliances, the cell phones, and etc. However, the electromagnetic field problems become prominent figures owing to the fault of the communication devices around the power line and the biological effect, and etc. In this paper, we introduce the simple electromagnetic field calculation based on the transmission line matrix method, prior to the analysis about the influence of electromagnetic field. Simulation object is the inner part of the trailer car in the high speed train. Unlike the existing paper we submitted, we analyze not only the magnetic field but the electric field in the inner part of the trailer car which makes up the high speed train.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.272-275
• /
• 2019

We investigated the electrical characteristics of amorphous silicon-zinc-tin-oxide (a-SZTO) thin films deposited by RF-magnetron sputtering at room temperature depending on the deposition time. We fabricated a thin film transistor (TFT) with a bottom gate structure and various channel thicknesses. With increasing channel thickness, the threshold voltage shifted negatively from -0.44 V to -2.18 V, the on current ($I_{on}$) and field effect mobility (${\mu}_{FE}$) increased because of increasing carrier concentration. The a-SZTO film was fabricated and analyzed in terms of the contact resistance and channel resistance. In this study, the transmission line method (TLM) was adopted and investigated. With increasing channel thickness, the contact resistance and sheet resistance both decreased.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.1-6
• /
• 2010

We report on the electrical properties of Ti/Al/Ni/Au (20 nm/ 150 nm/ 30 nm/ 100 nm) Ohmic contacts and the anisotropic conductivity of n-type ${\alpha}$-plane ([11-20]) GaN grown on $\gamma$-plane ([1-102]) sapphire substrates. The Ti/Al/Ni/Au Ohmic contacts and their sheet resistances are characterized by using the transfer length method (TLM) as a function of azimuthal angles. It is found that the specific contact resistance does not depend on the axis orientation and there are significant electrical anisotropy in ${\alpha}$-plane GaN films on $\gamma$-plane sapphire substrates, and the sheet resistance varies with azimuthal angles. The sheet resistance values in the direction parallel to m-axis [1-100] are 25% ~ 75% lower than those parallel to c-axis [0001] directions. Thus, Basal stacking faults (BSFs) are offered as a feasible source of the anisotropic mobility in defected m-axis direction because the band-edge discontinuities owing to the differential band gap structure.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.25-26
• /
• 2011

In this paper, we investigated the effect of various annealing processes on the electrical characteristics of oxide thin film transistors (TFTs). When we annealed the TFT devices before and after source/drain (S/D) process, we could observe the different electrical characteristics of oxide TFTs. When we annealed the TFTs after deposition of transparent indium zinc oxide S/D electrodes, the annealing process decreased the contact resistance but increased the resistivity of S/D electrodes. The field effect mobility, subthreshold slope and threshold voltage of the oxide TFTs annealed before and after S/D process were 5.83 and 4.47 $cm^2$/Vs, 1.20 and 0.82 V/dec, and 3.92 and 8.33 V respectively. To analyze the differences, we measured the contact resistances and the carrier concentrations using transfer length method (TLM) and Hall measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.33-36
• /
• 2004

탄소 도핑$(5{\times}10^{19}\;cm^{-3})$된 p-type GaAsSb 에피층 위에, Ti/Pt/Au, Pd/Au, Pd/Ir/Au를 이용한 다층 오믹 접촉을 제작하였다. MOCVD(metal-organic chemical vapor deposition)를 이용하여 성장시킨 이 p-GaAsSb의 정공 이동도는 탄소의 도핑 농도가 매우 높음에도 불구하고, $50\;cm^2/Vs$로 측정되었다. 오믹 접촉의 전기적 특성을 측정하기 위하여 TLM(Transfer length method)를 이용하였다. Pd/Ir/Au을 이용한 오믹접촉의 specific contact resistivity는 $10^{-8}\;ohm-cm^2$ 보다 작은 수치를, transfer length는 100 nm보다 작은 수치를 보였으며, Ti/Pt/Au을 이용한 ohmic contact의 specific contact resistivity는 $10^{-7|\;ohm-cm^2$ 보다 작은 수치를, transfer length는 400 nm보다 작은 수치를 나타내었다.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.213-216
• /
• 2001

The use of a thin film of indium between the ITO and the $n^{+}$-InP contact layers for InP/InGaAs HPTs was studied without degrading its excellent optical transmittance properties. ITO/$n^{+}$-InP ohmic contact was successfully achieved by the deposition of Indium and thermal annealing. The specific contact resistance of about 6.6$\times$$10^{-4}$$\Omega\textrm{cm}^2$ was measured by use of the transmission line method (TLM). However, as the thermal annealing was just performed to ITO/$n^{+}$-InP contact without the deposition of Indium between ITO and $n^{+}$-InP, it exhibited schottky characteristics. In the applications, the DC characteristics of InP/InGaAs HPTs with ITO emitter contacts was compared with that of InP/InGaAs HBTs with the opaque emitter contacts.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.133-136
• /
• 2004

In this study, the characteristics of 3C-SiC ohmic contact were investigated. Titanium-tungsten(TiW) films were used for contact metalization. The ohmic contact resistivity between 3C-SiC and TiW was measured by HP4155 and then calculated with the circular transmission line method(C-TLM). And also the physical properties of TiW and the interface between TiW and 3C-SiC were analyzed using XRD and AES. TiW films make a good role of a diffusion barrier and their contact properties with 3C-SiC are stable at high temperature.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.1995-2000
• /
• 1989

The ion beam system of 20keV C-W (Cockroft Walton) type composed of the AuGe alloy LMIS(Liquid Metal Ion Source) has been designed and constructed. For the fabrication of the ohmic contact to the n-GaAs, the ion beam extracted from the AuGe alloy source was implanted into the n-GaAs, and it was measured by contact resistivity. The stable AuGe ion beam(2.5\ulcorner/cm\ulcorner was obtained at the extraction voltage of 14.5kV. The measurements of the contact resistivity were done by the TLM (Transmission Line Model) method and the specific contact resistivity was found to be 2.4x10**-5 \ulcornercm\ulcornerfor the implanted sample by the 1.9x10**20/cm**3 and the annealed sample at 30\ulcorner for 2 min.