• Composites Research
• /
• v.23 no.6
• /
• pp.1-6
• /
• 2010

The electrical conductivity of carbon-fiber reinforced plastics (CFRP's) has been improved by indium-tin oxide (ITO) nano-particle coating on carbon fibers for the purpose of lightning strike protection of composite fuselage skins. ITO nano-particles were coated on the surface of carbon fibers by spraying the colloidal suspension with 10~40% ITO content. The electrical conductivity of the CFRP has been increased more than three times after ITO coating, comparable to or higher than that of B-787 composite fuselage skins with metal wire-meshes on the outer surface, without sacrificing the tensile property due to the existence of nano-particles at fiber-matrix interface. The damage area by the simulated lightning strike was also verified for different materials and conditions by using ultrasonic C-scan image. As the electrical conductivity of 40% nano-ITO coated sample surpass that of the B-787 sample, the damage area by lightning strike also appeared comparable to that of the materials currently employed for composite fuselage construction.

• Composites Research
• /
• v.23 no.6
• /
• pp.61-66
• /
• 2010

In this paper, the variation of mechanical properties of T800 carbon/epoxy composites according to the forming pressure, which was referred to previous studies on a filament winding process, were investigated. The specimens of all the tests were fabricated by an autoclave de-gassing molding process controlling forming pressure (absolute pressures of 0.1MPa, 0.3MPa, 0.7MPa including vacuum) and water jet cutting after fabricating composite laminates. Various tensile tests were performed for in-plane properties and interlaminar properties were also measured by using Iosipescu test jig. Fiber volume fraction was measured to correlate the property variation and the forming pressure. This properties are expected to be utilized in the design of Type III pressure vessel for hydrogen vehicles which uses the same carbon fiber (T800 carbon fiber) for the filament winding process.

• Composites Research
• /
• v.33 no.4
• /
• pp.213-219
• /
• 2020

Recently, global facing environmental issues have been raised caused by plastic waste. Hence, increasing the demand for interest in environmentally friendly materials. In this row, research on engineering composite materials also replacing the synthetic reinforcement by introducing natural fibers. However, focus on the strength and interfacial adhesion between matrix and reinforcement is very essential in natural fiber composite, which is insufficient in the literature. There are number of approaches for improving the mechanical strength of the composites, one of the common methods is to reinforce additive nanoparticles. The present investigation, bio-additives were synthesized utilizing bio-waste, cheap, bio-degradable sea-weed powder that could replace expensive nanomaterials and reinforced into the CFRP composite through Hand lay-up followed by a vacuum process. Mechanical properties were evaluated and analyzed through microanalysis. The results concluded that synthesized additives are effective for improving mechanical properties such as tensile, flexural, impact, and shear strength. Overall, the results confirmed that the fabricated composites have potential applications in the field of engineering applications.

• Structural Engineering and Mechanics
• /
• v.54 no.5
• /
• pp.855-875
• /
• 2015

Many novel materials exhibit a property of different elastic moduli in tension and compression. One such material is graphene, a wonder material, which has the highest strength yet measured. Investigations on buckling problems for structures with different moduli are scarce. To address this new problem, firstly, the nondimensional expression of the relation between offset of neutral axis and deflection curve is derived based on the phased integration method, and then using the energy method, load-deflection relation of the rod is determined; Secondly, based on the improved constitutive model for different moduli, large deformation finite element formulations are developed and combined with the arc-length method, finite element iterative program for rods with different moduli is established to obtain buckling critical loads; Thirdly, material mechanical properties tests of graphite, which is the raw material of graphene, are performed to measure the tensile and compressive elastic moduli, moreover, buckling tests are also conducted to investigate the buckling behavior of this kind of graphite rod. By comparing the calculation results of the energy method and finite element method with those of laboratory tests, the analytical model and finite element numerical model are demonstrated to be accurate and reliable. The results show that it may lead to unsafe results if the classic theory was still adopted to determine the buckling loads of those rods composed of a material having different moduli. The proposed models could provide a novel approach for further investigation of non-linear mechanical behavior for other structures with different moduli.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.774-779
• /
• 2016

This study was performed to study the possibility of TMCP's application for side shell plating curved structures through mechanical property testing to understand if the rules and regulations of DNV and the quality standard of IACS after line heating for TMCP steel and normalizing DH32 material steel could be satisfied. Experimental results showed that TMCP's strength was measured to YS = 385 MPa, 18% higher than the required 315 MPa and TS = 525 MPa, complying with the required range of between 440 and 570 MPa. The minus 20 degree impact test for the Charpy V-Notch complied with the required standard and in addition the hardness test satisfied the requirement of 'Hv10 = 130 ~ 320' by reaching an average of T : 216 and L : 275 respectively.

• Journal of Adhesion and Interface
• /
• v.12 no.1
• /
• pp.34-42
• /
• 2011

The roll coating process is well-known for completely replacement coating system with an existing wet paint process for automotive which has low productivity and is not environment-friendly process. It is very important to evaluate the curing behavior, corrosion resistance and processing property as well as rheological behavior in order to realize a film flexibility and hardness simultaneously. In this study, we have synthesized the polyester resin modified with hydroxyl values and molecular weight to apply the pre-painted system, and then evaluated the curing behavior, deep drawing, tensile strength and rheological properties. It was observed that N-0375-40 of 40 (mg KOH/mol) hydroxyl values showed the most suitable for flexibility, film hardness, and curing behavior.

• Journal of the Korean Chemical Society
• /
• v.54 no.2
• /
• pp.228-233
• /
• 2010

Recently, nanoparticles of gold and silver has been applied to various fields due to antimicrobial property. This study added Ag and Au nanoparticles in HEMA (2-hydroxyethylmethacrylate), NVP (N-vinyl pyrrolidone) and MMA (methylmethacrylate) and copolymerized the solution by heating at $70^{\circ}C$ for 40 minutes, $80^{\circ}C$ for 40 minutes, and finally, $100^{\circ}C$ for 40 minutes. Using the polymer produced through the copolymerization process, and measured the physical characteristics which showed water content of 28.43% ~ 35.27%, refractive index of 1.429 ~ 1.440, visible transmittance of 79.2% ~ 86.5% and tensile strength of 0.125 kgf ~ 0.201 kgf. We judged that we made the copolymer with antimicrobial and physical properties which is suitable for conventional contact lens.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.364-370
• /
• 2009

The curing kinetics and mechanical properties of siloxane-diaminodiphenylmethane (ETSO-DDM) on the two kinds of bisphenol (BPH) system which are DGEBA and DGEBF were investigated with the different contents of ETSO. To investigate the curing kinetics of the ETSO-DDM/BPH systems, differential scanning calorimeter (DSC) was used. The mechanical properties of ETSO-DDM/BPH systems were also examined by universal testing machine (UTM), tensile test and flexural test. From experimental results, the activation energies and mechanical properties of ETSO-DDM/BPH were improved with the decrease contents of ETSO. This was due to the high cross-linking density made from short length of ETSO-DDM, resulting in improving the mechanical inter-locking between ETSO-DDM and BPH in these systems.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.34-40
• /
• 2013

Commercially available polyamide thermoplastic elastomer (PA-TPE) was blended with hybrid filler which was prepared by means of the reaction between polyhedral oligomeric silsesquioxane (POSS) containing amine group and toluene diisocyanate (TDI)-caprolactam (CL) to explore the effect of blending the hybrid filler with the TPE. The chemical structure of the filler was identified by using FTIR and $^1H$ NMR. The composites, PA-TPE/POSS-(TDI+CL), which were the blends of TDI+CL modified POSS filler and PA-TPE up to 7 wt%, showed better elastic recovery delivered from lower tension setting compared to the PA-TPE and the PA-TPE/octaphenyl POSS blend. In addition the tensile strength and the initial modulus increased with increasing the hybrid filled content. Consequently it was assumed that the POSS-(TDI+CL) filler was a suitable material for enhancing strength and modulus without loss of elastic properties for the original PA-TPE.

• The Journal of the Petrological Society of Korea
• /
• v.6 no.1
• /
• pp.34-44
• /
• 1997

The Jurassic granites, commercially called Yangu stone in the Pocheon-Euijeongbu area, have generally compact and coarse-grained textures, which could be classified into two types; grey granite(Gg) and light pink granite(Gp). Specific gravity, absorption ratio and prosity of Gg and Gp in physical property are 2.64 and 2.61, 0.32 % and 0.44 %, 0.86% and 1.13 %, respectively. These higher values of two latters of Gp than those of Gg are due to the more abundant microcracks in Gp. Compressive strength og Gg than those of Gg are due to more abundant microcracks in Gp. Compressive strength og Gg and Gp are 1,726 kg/cm2 and 1,717 kg/cm, respectively and bestrength has a positive proportion with Qz+Af+Pl(quartz+alkali feldspar+plagioclase) modes without trending with Bt+Ac(biotite+accessories). Tensile strength has the positive proportions with Qz+Af+Pl and Bt+Ac. While Bt+Ac has a negative trend with abrasive hardness, Qz+A+Pl shows a positive one. These may suggest Qz+Af+Pl mainly affects on strenghts potentional dimension stone than Gp.