• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.656-665
• /
• 2021

In this study, trim tabs were attached to end of stern hull of a small high-speed vessel of length approximately 10 m and Froude number 1.0 to improve resistance performance and passenger comfort. Before computational fluid dynamics (CFD) simulations to assess the performance according to various geometries of the trim tab, the scale effect had been found through a previous study, so full-scale simulations were performed. The trim tab chord length was set to 0.5 %, 1.0 % and 1.5 % of L_PP, and its angle to base line was varied in intervals of 5°. It decreased trim by stern and flotation: the greater the angle and length, the greater was the effect. Then it had pressure resistance decreased and shear resistance increased, and reduction ratio of total resistance varied accordingly. The results of this study indicated that the resistance performance was improved about 27 % at optimal running attitude that was the trim by stern about 1.5°.

• Journal of Korean Institute of Industrial Engineers
• /
• v.41 no.2
• /
• pp.137-143
• /
• 2015

This thesis focuses on the 3D interface tab page type and mode of screen that affect the usability of the small screen devices such as smartphone. The experiments examined eight 3D UI designs, combinations of two modes (Portrait, Landscape) of screen, and four types (Vertical data mountain, Horizontal data mountain, Vertical carousel, Horizontal carousel). Twenty-six participants participated in the experiment. The completion time, preference and fun score were measured. The results showed that the vertical data mountain type provide the best performance in terms of the all conditions. The results of this study suggest a practical approach for the 3D UI tab page design for the small screen devices.

• Steel and Composite Structures
• /
• v.1 no.3
• /
• pp.329-340
• /
• 2001

Cyclic response of "shear" connections between steel outrigger beams and reinforced concrete core walls is presented in this paper. The connections investigated in this paper consisted of a shear tab welded onto a plate that was connected to the core walls through multiple headed studs. The experimental data from six specimens point to a capacity larger than the design value. However, the mode of failure was through pullout of the embedded plate, or fracture of the weld between the studs and plate. Such brittle modes of failure need to be avoided through proper design. A capacity design method based on dissipating the input energy through yielding and fracture of the shear tab was developed. This approach requires a good understanding of the expected capacity of headed studs under combined gravity shear and cyclic axial load (tension and compression). A model was developed and verified against test results from six specimens. A specimen designed based on the proposed design methodology performed very well, and the connection did not fail until shear tab fractured after extensive yielding. The proposed design method is recommended for design of outrigger beam-wall connections.

• Journal of ILASS-Korea
• /
• v.5 no.2
• /
• pp.53-60
• /
• 2000

An aerodynamically progressed model, which is called APTAB model. has been proposed for more accurate prediction of the deformation and breakup of a spray. Especially, the effects of the droplet deformation on the droplet aerodynamic external force are considered in this model, which was neglected in TAB model. It is found that the predicted droplet deformation using APTAB model shows better agreement with experimental data than those of other models for the droplets in both bag-type and shear-type breakup regimes. A new breakup criterion has been proposed to predict more reasonable breakup quantities, such as breakup deformation length, time and so on; i.e., it is defined that the breakup occurs when the internal liquid phase pressure of the deformed droplet at the equator is greater than that of the pole. The proposed breakup criterion shows more physical relationship between the degree of droplet deformation at breakup and the corresponding breakup Weber number as compared with the results with TAB and DDB models. Therefore, it provides better predictions of the experimental data than TAB and DDB models for the droplet deformation and time in both bag-type and shear-type breakup regimes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.486-491
• /
• 2013

Creak noise is kind of scratching noise which is usually generated in drum brake system on the vehicle. When driver brakes vehicle or applies parking lever, drum brake shoe moves to the drum side to stop the vehicle. And at that time, moving shoe scratches backing plate ledge surface, and that makes scratching noise in special condition. This study presents how we can generate creak noise in the laboratory and how we can reduce it by experimental approach. Through several and various type of tests, we could generate creak noise with damage on ledge area of the backing plate in the lab and we verified tab type shoe design can reduce this scratching noise. As a result of this study, we notified how creak noise happens in the vehicle, and that tab type design shoe has good performance of ledge area damage based on lab test(rig & dynamometer equipment), and that this can reduce potential risk of creak noise in the field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.8-22
• /
• 1995

Three dimensional numerical study of non-evaporating and evaporating spray characteristics was performed in a quiescent and motoring condition of direct injection diesel engine. The calculation parameter was breakup model. The breakup models used were Reitz & Diwakar model and TAB model. The modified k-${\varepsilon}$ turbulence model considering the compressibility effect due to the compression and expansion of piston was used. The calculation results of the spray tip penetration and tip velocity using the TAB model showed similar trends comparing with the experimental data. Although the evaporation rate was not nearly affected with the breakup model at the higher injection pressure, in the low injection case, the evaporation rate result using the TAB model became higher than that of R&D model. The evaporation rate was increased with the injection pressure due to the vigorous interaction with the gas field.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.3
• /
• pp.158-165
• /
• 1994

Cu-Cr alloy thin film requires good quality of etching be used for TAB technology. The etched cross sec-tion was clean enough when the etching was performed in 0.1M $FeCl_3$ solution at $50^{\circ}C$. The etching rate was increased with the amount of $KMnO_4$. For enhanced profile of cross section and rate, the spray etchning was found to be superior compared to the immersion etching. A series of experiments were performed to improve the uniformity of the current distribution in electrodeposition onto the substrate with lithographic patterns. Copper was electrodeposited from quiescent-solution, paddle-agitated-solution, and air-bubbled-solution to in-vestigate the effect of the fluid flow. The thickness profile of the specimen measured by profilmetry has the non uniformity at feature scale in quiescent-solution, because of the longitudinal vortex roll caused by the natural convection. However, uniform thickness profile was achieved in paddle-agitated or air bubbled solu-tion.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.70-75
• /
• 2009

Most hard disk drives uses load/unload technology because of benefits as like an increased areal density, a reduced power consumption and an improved shock resistance. However, ramp tilt induced by ramp manufacture and assembly causes mechanical problems such as unload fail in case of exceeding ramp tolerance. In this paper, we focus on experimental analysis for unloading characteristics affected by ramp tilt. We repeatedly perform load/unload test as 500,000 cycles for original model and ramp tilt model. This paper shows that it is possible to analyze unload characteristics through measuring scratch and wear of suspension lift-tab, ramp, suspension dimple-flexure and disk. We also identify structural relation between suspension lift-tab and ramp through scratch and wear of suspension lift-tab and ramp. As the result of measurement and analysis, we can investigate decrease of unloading performance in ramp tilt model.

• Fire Science and Engineering
• /
• v.23 no.5
• /
• pp.84-89
• /
• 2009

In this study, the fire extinguishing experiment was performed using a water mist nozzle with variation of factors which affect on the extinguishing time. The variables were distance from nozzle center to fire location, droplet size, height of nozzle and opening or not. With the experimental data, interaction and sensitivity between factors were analysed with Mini tab and deduce a optimum model of fire extinguishing of water mist system. Based on the experiment and modeling of fire extinguishing with water mist system, the most important factor on extinguishing time is the distance from the center of nozzle to fire and the opening effect was small compare with other factors.

• Journal of the Korean Institute of Educational Facilities
• /
• v.12 no.6
• /
• pp.26-35
• /
• 2005

The purpose of this study is to suggest improved Special Instruction Classrooms(SIC) in terms of architectural planning based on the analysis of design characteristics and problems. For this study, SICs in 20 elementary schools located in Daegu were selected and investigated. The results of investigation showed that: first, the vertical separation type is mostly preferred for the layout of SICs; second, the top floor is preferred for the location of SICs. We suggest that first, each SIC should be located with consideration of the characteristics of subjects(); second, the degree of adjacency-room preference for each room should be taken into consideration for the zoning of the SICs(, ); finally, a direction for improvement for suitable architectural design of each SICs should be based on the feasibility of learning space().