• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.83-93
• /
• 2014

It is a widespread concern that electrical interconnection based network-on-chip (NoC) will ultimately face the limitation in communication bandwidth, transmission latency and power consumption in the near future. With the development of silicon photonics technology, a hybrid optical network-on-chip (HONoC) which embraces both electrical- and optical interconnect, is emerging as a promising solution to overcome these problems. Today's leading edge systems-on-chips (SoCs) comprise heterogeneous many-cores for higher energy efficiency, therefore, extended study beyond regular topology based NoC is required. This paper proposes an energy and latency optimization topology design technique for HONoC taking into account the traffic characteristics of target applications. The proposed technique is implemented with genetic algorithm and simulation results show the reduction by 13.84% in power loss and 28.14% in average latency, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.494-502
• /
• 2001

GPS(Global Positioning System) and GLONASS(GLObal Navigation Satellite System) are basic technologies providing the information of the position and the time, and they have various applications such as navigation, survey, control, and so on. However, each GPS and GLONASS has limited number of visible satellites, and, from the view of strategy, it is undesirable to be heavily dependent on only one system. Thus, GPS/GLONASS combined receiver became required to obtain more precise navigation and system stability. In this paper, the RF front end of GPS/GLONASS combined receiver was fabricated on 130$\times$80 $\textrm{mm}^2$ PCB(Printed Circuit Board), and its system application was shown finally one chip possibility of GLONASS receiver is studied.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.661-665
• /
• 2000

In this study, the control of mounting system for MLGA package was developed using machine vision for the control of rotating position compensation and mounting position of X-Y table. Two type of material (polymer, alumina )were used for the dielectric insulator of the MLGA. And the illumination system and the algorithm of position compensation that be suitable for these materials was developed. Also, the position control order that compensated by machine vision actuated to micro stepping motor and X-Y servo motor by controlled PC and mounted the MLGA on PCB in resolution to$\pm10\mum$ .

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.161-167
• /
• 2001

In this study, the control of mounting system for MLGA package was developed using machine vision for the control of rotation position compensation and mounting position of X-Y table. Two types of materials, polymer and alumina, were used for the dielectric insulator of the MLGA. The illumination system and the algorithm of position compensation which is suitable for these materials was developed. We found that the mounting accuracy enough to the degree of${\pm}10{\mu}m$ when MLGA was mounted on the PCB.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.751-754
• /
• 1998

This research aims at developing a single chip multiprocessor for high-performance computer system. Our design approach is to design a relatively small and simple processor unit and to integrate multiple copies of the unit in an efficient way. The proposed multiprocessor is composed of four CPUs and one graphic coprocessor. The four CPUs share the graphic coprocessor and each CPU implements the 64-bit SPARC-V9 instruction set architecture. This paper gives an overview of the proposed microarchitecture and discusses the considerations made in the course of the design.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.70-82
• /
• 2003

마이크로파 능동필터는 RF 시스템에서 주목받고 있는 SoC(System on Chip) 기술을 위한 필터의 집적화 기술로 매우 활발한 연구가 수행되어지고 있다. chip상에서의 마이크로파 대역에서의 능동필터는 기판의 손실로 인한 공진기의 Q값 저하를 능동소자를 이용하여 보상하여 협대역 필터의 구현을 가능하게 할 뿐만 아니라, 바랙터 다이오드나 PIN 다이오드을 회로에 적용하여 가변 필터의 구현도 가능하게 되어 시스템의 유연성이 높은 SDR (Soft-wave Defined Radio)등에도 적용될 수 있는 분야로 각광을 받을 것으로 판단된다. 본 고에서는 마이크로파 능동 필터에 대한 분류와 회로의 구조 연구 동향에 대해 살펴본다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2000.04a
• /
• pp.36-38
• /
• 2000

An optoelectronic database filter chip for high performance database computers and applications is proposed. The proposed device is designed to perform the selection and projection operations of relational database operation on-the-fly in page-parallel manner to increase the overall performance of a database system. The device utilizes CMOS smart pixel array consists of detector and combinational logic circuit to perform the selection and projection operation.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.921-924
• /
• 1993

For the purpose of applying to a high-speed control system, such as engine control for automobile application, we propose an architecture of a fuzzy inference processor, which can realize high-speed inference, high-resolution, and can be implemented with small chip area. We have designed a single chip based on the architecture, and confirmed the performance, such as 140 kFLIPS with 8-bit resolution.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2624-2630
• /
• 2013

In LED chip packaging, die bonding is a very important process which fixes the LED chip on the lead flame to provide enough strength for the next process. During the process, inspection processes are very important to detect exact locations of dispensed epoxy dots and to determine bonding status of dies whether they are lies at exact positions with sufficient bonding strength. In this study, a useful machine vision based inspection system is proposed for the LED die bonder. In the proposed system, 2 cameras are used for epoxy dot position detection and 2 cameras are sued for die attaching status determination. New vision processing algorithm is proposed, and its efficiency is verified through required field experiments. Measured position error is less than $X:-29{\mu}m$, $Y:-32{\mu}m$ and rotation error:$3^{\circ}$ using proposed vision algorithm. It is concluded that the proposed machine vision based inspection system can be successfully implemented on the developed die bonding system.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.45.4-45
• /
• 2001

In this paper, we present the wet-based monitoring system for industrial controller such as inverter controller for hydraulic elevators. The monitoring system is using an embedded web server on embedded Linux platform. The control board of system-On-Chip (SoC) is based on ARM7TDMI with Ethernet controller. Wet-based monitoring system using embedded Linux platform can reduce the cost, and have flexibility both of technical issues and locations If the system to be monitored. The system shows the feasibility of remote monitoring system based on embedded Linux platform.