• Journal of the Korean Society for Precision Engineering
• /
• 제23권1호
• /
• pp.201-208
• /
• 2006

Recently, there are many studies for the micro-machining using Piezo actuator. However, because of its step-by-step motion, it is nearly impossible to increase the machining accuracy for a circular path. To increase the accuracy, it is well known that it is necessary the finer and synchronous movement for x-y axes. Therefore, this paper proposes an adaptive control for finer movement of the actuator, and realizes a synchronous control for the x-y axes. The experimental results show that the machining accuracy is remarkably improved.

• Journal of Electrical Engineering and Technology
• /
• 제10권6호
• /
• pp.2297-2306
• /
• 2015

This paper presents the development of a system with a reverse matrix converter (RMC) for permanent magnet synchronous motor (PMSM) drive and its effective control method. The voltage transfer ratio of the general matrix converter is restricted to a maximum value of 0.866, which is not suitable for applications whose source voltages are lower than the load voltages. The proposed RMC topology can step up the voltage without any additional components in the conventional circuit. Its control method is different from traditional matrix converter’s one, thus this paper proposes control schemes of RMC by means of controlling both the generator and motor side currents with properly designed control loop. The converter can have sinusoidal input/output current waveforms in steady state condition as well as a boosted voltage. In this paper, a hardware system with an RMC for a PMSM drive system is described. The performance of the system was investigated through experiments

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• 제25권3호
• /
• pp.15-23
• /
• 2011

This paper proposes a nonlinear speed controller for a permanent magnet synchronous motor (PMSM). In this paper, the load torque is estimated by an extended Kalman filter (EKF) observer because the proposed controller needs its knowledge. To confirm the effectiveness of the proposed control scheme, simulations and experiments are performed under motor parameter variations with a prototype PMSM drive system.

• International Journal of Control, Automation, and Systems
• /
• 제3권spc2호
• /
• pp.308-314
• /
• 2005

Transient stabilization with voltage regulation is investigated for a synchronous generator when the mechanical power is perturbed to any unknown value within its physical bounds so that the operating point of the system shifts to an unknown point. An adaptive excitation controller is designed based on the backstepping method with tuning functions. It will be shown that the adaptive control law proposed can achieve the convergence of the system states to the new equilibrium point in correspondence with the real value of the unknown mechanical power and the regulation of the terminal voltage to the required value. Simulation results are given to demonstrate the effectiveness of the proposed controller for the transient stabilization and voltage regulation.

• Journal of Institute of Control, Robotics and Systems
• /
• 제22권5호
• /
• pp.315-319
• /
• 2016

This paper proposes a simple adaptive sliding mode control algorithm for controlling a permanent magnet synchronous generator (PMSG) of a MW-class direct-driven wind turbine system. The proposed adaptive sliding mode controller does not require accurate knowledge of the PMSG parameter or turbine torque values. The proposed controller can accurately track the reference angular speed computed by the maximum power point tracking(MPPT) algorithm. Finally, this paper gives Matlab/Simulink simulation results to verify the practicality and effectiveness of the proposed adaptive sliding mode controller.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권2호
• /
• pp.23-29
• /
• 2012

The control of stator flux, torque angle, excitation torque, reluctance torque and total torque of the direct torque control (DTC) for a permanent magnet synchronous motor (PMSM) are studied in this paper. Simplified expressions to represent the changes of these variables due to the application of a voltage vector are given. Finally, a voltage vector selection area and the implementation of a voltage vector selection strategy are proposed.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.596-599
• /
• 1989

Vector control has been widely used in AC machines for precise control. The application of Vector control for the permanent magnet synchronous motor drive and complete modeling,simulation and analysis of the drive are discussed in this paper. The nonlinear model of the permanent magnet synchronous motor is linearized. Then the theory of vector control is applied to the linearized model in designing controllers. The operation and relevant mathematics model of s pseudo derivative feedback controller are then presented. Two different speed controller design are then considered. A comparative evalation of the two speed controller is also presented.

• Proceedings of the KIPE Conference
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.485-487
• /
• 2006

Speed and torque controls of permanent magnet synchronous motors are usually attained by the application of position and speed sensors. However, speed and position sensors require the additional mounting space, reduce the reliability in harsh environments and increase the cost of a motor. Therefore, many studies have been performed for the elimination of speed and position sensors. This paper investigates an Improved sliding mode observer for the speed sensorless control of a permanent magnet synchronous motor. The proposed control strategy is the sliding mode observer with a variable boundary layer for a low-chattering and fast-reponse control. The proposed algorithm is verified through the simulation and experimentation.

• Journal of Power Electronics
• /
• 제13권4호
• /
• pp.669-678
• /
• 2013

This paper proposes a sensorless control approach for Wound Rotor Synchronous Machines (WRSMs) based on a high frequency voltage signal injection into the stator side U phase and VW line, respectively. Considering the machine itself as a rotor position sensor, the rotor position observer is established according to the principles of the rotary transformer. A demodulation method for the high frequency signal inducted in the rotor is proposed as well. Simulation and experimental results show that the proposed sensorless control approach has high performance and good practicability.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권3호
• /
• pp.121-130
• /
• 1996

Permanent magnet synchronous motor is widely used in industrial drive applications due to high efficiency, high power ratio, and easy maintenance. Position and speed detectors required in this motor increase the drive cost, and reduce the application range. Some papers present the speed control without position and speed detectors using DSP characterized by high processing performance. However, DSP increases the cost, and makes the inplementation difficult. This study has performed the speed control without position and speed detector by means of the microprocessor system which can be easily accessed. The results of simulation and experiment showed comparatively good dynamics in spite of the sensorless system.