• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.5
• /
• pp.315-320
• /
• 2022

In the case of a general spiral inductor, the orientation of the port is affected as it has an asymmetric structure. In this paper, double-layer spiral inductor that can have a symmetrical structure is proposed, and the simulation and frequency characteristics are analyzed. Compared to the conventional single-layer symmetrical inductor having an inductance of 3.9~4.2nH, the proposed double-layer symmetric spiral inductor has an inductance of 11~12nH in 0.3~1.2GHz frequency range, a quality factor of about 4.4 in 800MHz, and a self-resonant frequency of about 2.7~2.8GHz without changing the port. Compared to the general spiral inductor having a large difference depending on the port, it was confirmed that the influence on the port direction was small.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.4
• /
• pp.1748-1759
• /
• 2018

Weber Local Descriptor (WLD) is a stable and effective feature extraction algorithm, which is based on Weber's Law. It calculates the differential excitation information and direction information, and then integrates them to get the feature information of the image. However, WLD only considers the center pixel and its contrast with its surrounding pixels when calculating the differential excitation information. As a result, the illumination variation is relatively sensitive, and the selection of the neighbor area is rather small. This may make the whole information is divided into small pieces, thus, it is difficult to be recognized. In order to overcome this problem, this paper proposes Weber Symmetrical Local Graph Structure (WSLGS), which constructs the graph structure based on the $5{\times}5$ neighborhood. Then the information obtained is regarded as the differential excitation information. Finally, we demonstrate the effectiveness of our proposed method on the database of ORL, JAFFE and our own built database, high-definition infrared faces. The experimental results show that WSLGS provides higher recognition rate and shorter image processing time compared with traditional algorithms.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.184-191
• /
• 2002

This paper presents the thermal behavior of a synchronous linear motor with high speed and force. Such a linear motor can successfully replace ball lead screw in machine tools because it has a high velocity, acceleration and good positioning accuracy. On the other hand, low efficiency and high heating up during operation are disadvantage of linear motors. For the application of linear motors to machine tools a water-cooling system is often used. In this research, structure of the linear motor and water cooler is changed to improve the thermal behavior of the linear motor. Some important effects of an integrated cooler, an U-cooler and a thermally symmetrical cooler are presented.

• Korean Journal of Veterinary Research
• /
• v.53 no.4
• /
• pp.207-210
• /
• 2013

Fifteen dry dentate and complete mandible samples from the White Rasquera goat breed were studied for symmetry. Thirty-one landmarks were digitally located on the images of the lateral and medial aspects of each hemimandible. Distances between these landmarks allowed the evaluation of the whole hemimandible and also the neural mandible. In the studied samples, the mandible was rather symmetrical, especially in the medial neural part, and in general, there was no side dominance. Only the diastema differed significantly between the sides, and this was related to the rostral part (incisive arch). The incisive region was the least symmetrical region of the caprine mandible, indicating a modular structure more conservative for the neural part. If unsigned asymmetry is interpreted as a measure of developmental stability, then the studied breed presented a marked ability to develop in good fitness despite the harsh environment. The measurements presented here can also be used as a reference for researchers designing experimental studies, especially on mandibular catch-up growth, and as an aid for zooarchaeologists comparing results from dead animals with those from living goat populations.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.1201-1202
• /
• 2008

In this paper, using symmetrical condensed node(SCN), the TLM numerical technique has been successfully applied to microstrip meander line. A detailed technique of the symmetrical condensed node(SCN) may be used to model planar microstrip transmission line is presented. Also, the S-parameters $S_{11}$ and $S_{21}$ of microstrip meander line have been computed. From obtained results, TLM analysis is shown to be an efficient method for modeling complicated structure of planar microstrip transmission line.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.1003-1006
• /
• 2008

Highly efficient syntheses of cylindol A (1) and the proposed structure of cylindol B (2) have been accomplished using common synthetic transformations from symmetrical starting materials 7 and 11, respectively. The latter synthesis revealed that the proposed structure of the natural cylindol B was assigned incorrectly. Isomers of 2 such as 15 and 16 were synthesized as a possible candidate of the natural cylindol B. However, their spectral data also did not match that of the natural cylindol B. Therefore, the structure of the natural cylindol B is yet to be resolved.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.353-358
• /
• 2020

In the case of a general spiral inductor, the orientation of the port is affected as it has an asymmetric structure. In this paper, a single-layered spiral inductor that can have a symmetrical structure is proposed, and the simulation and frequency characteristics are analyzed. The general spiral inductor shows a large difference in frequency-inductance characteristics, frequency-quality factor characteristics, and self-resonant frequency according to the standard of the port, while the proposed symmetric spiral inductor has an inductance of 2.7nH, a quality factor of about 7.86, and a self-resonant frequency of about 14.1GHz without changing the port. Compared to the general spiral inductor having a large difference depending on the port, it was confirmed that the influence on the port direction was small. However, it was confirmed that the mutual inductance decreased compared to the occupied area of the coil, resulting in a low inductance, and the resistance of the coil increased more than the increase in the inductance, and the quality factor was also lowered. In the future, it is expected that inductance and quality factor can be improved through a 2-layer symmetrical spiral structure.

• Journal of Technology Innovation
• /
• v.14 no.2
• /
• pp.143-165
• /
• 2006

By analyzing five in-depth case studies of suppliers in newly emerging Vietnam's motorcycle industry, this paper explores the differences in patterns and processes of capability improvement of suppliers who participate in different kinds of supplier-assembler network with different structures. The paper finds the correlation between the kinds of suppliers' capabilities improved and the structure of networks they participate in. While suppliers in arm-length networks can improve more upstream capabilities (structure design, process desist), suppliers in embedded networks can improve more downstream capabilities (process design, process setup, process maintenance and delivery control). Two capability improvement patterns of firms in newly emerging economy are indicated. The first pattern is asymmetrical improvement, either upstream or downstream capabilities, by participating in either arm-length or embedded networks. This pattern obstructs the suppliers to meet the requirements of new buyers rho come from different kinds of network. The second pattern is symmetrical improvement by joining both arm-length and embedded networks.

• Journal of the Korean Vacuum Society
• /
• v.8 no.2
• /
• pp.121-126
• /
• 1999

Cu thin film was deposited by a self-ion assisted beam source (SIAB) and the assessment of the Cu films was given. Some characteristics of the source and the experimental procedure are described at various conditions such as total power, ionization efficiency, and ion current vs. deposition rate. The dependence of crystalline structure, impurity concentration, and resistivity of the Cu films deposited by SIAB on acceleration voltage are discussed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.04a
• /
• pp.122-127
• /
• 1990

The transfer of forces across the interface by bond between concrete and steel is of fundamental importance to many aspects of reinforced concrete behavior. Bond stress - slip relationships were studied using a symmetrical tension test specimen. This type of test is intented to simulate conditions in the tension zone of a concrete beam between primary cracks and below the neutral axis. These relationships between local bond stress and local slip are quite different at different locations along the bar. The present study allows more accurate analysis of reinforced concrete structures by employing more realistic bond stress-slip relations.