• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.371-378
• /
• 2015

In this paper, a different type of pulse width modulation (PWM) control scheme for a buck converter is introduced. The proposed buck converter uses PWM with frequency hopping and a low quiescent.current low dropout (LDO) voltage regulator with a power supply rejection ratio enhancer to reduce high spurs, harmonics and output voltage ripples. The low quiescent.current LDO voltage regulator is not described in this paper. A three-bit binary-to-thermometer decoder scheme and voltage ripple controller (VRC) is implemented to achieve low voltage ripple less than 3mV to increase the efficiency of the buck converter. An internal clock that is synchronized to the internal switching frequency is used to set the hopping rate. A center frequency of 2.5MHz was chosen because of the bluetooth low energy (BLE) application. This proposed DC-DC buck converter is available for low-current noise-sensitive loads such as BLE and radio frequency loads in portable communications devices. Thus, a high-efficiency and low-voltage ripple is required. This results in a less than 2% drop in the regulator's efficiency, and a less than 3mV voltage ripple, with -26 dBm peak spur reduction operating in the buck converter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.41-48
• /
• 2004

In this paper, a PFC(Power Factor Correction) electronic ballast with constant voltage-fed is proposed. The proposed PFC electronic ballast is combined of a high-efficiency boost converter and a conventional half bridge inverter. It is proved that the ripple of input-current and the input-current's harmonic of the proposed PFC electronic ballast are reduced using the voltage divider and soft-switching technique. It is demonstrated that simulation results for fluorescent lamp correspond with theoretical analysis.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1296-1299
• /
• 2001

In this paper, a simple, novel approach is proposed for a variable hysterisis band current controller which uses feedback techniques to achieve constant switching frequency with good dynamic response. The simulation result shows constant switching frequency and consequenctly the load current ripple decrease.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.994-1003
• /
• 2016

Two major obstacles in the utilization of electrical vehicles are their price and range. The collaboration of direct torque control (DTC) with induction motor (IM) is preferred for its low cost, easy implementation, and parameter independency. However, in terms of edges, the method has drawbacks, such as variable switching frequency and undesired current harmonic distortion. These drawbacks result in acoustic noise, reduced efficiency, and electromagnetic interference. A feed-forward approach for stator-flux-oriented DTC with space vector pulse-width modulation is presented in in this paper. The outcome of the proposed method is low current harmonic distortion with fixed switching frequency while preserving the torque performance and simple application feature of basic DTC. The method is applicable to existing and forthcoming IM drive systems via software adaptation. The validity of the proposed method is confirmed by simulation and experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.7
• /
• pp.1061-1067
• /
• 2008

Direct Torque Control[DTC] and Vector Control are the two schemes developed for high performance induction motor drives. DTC based induction motors are being increasingly used in various industrial applications. DTC offers fast torque response and better speed control with lesser hardware and processing costs as compared to vector controlled drives. However, conventional DTC suffers from high torque ripple, current harmonics and low performance during torque transients. In this paper a new Direct Torque Control[DTC] method of induction motor is presented. In comparison with the conventional DTC method, the PWM technique is applied to proposed control method. In this method, decoupling mechanism is not required and the torque, the flux magnitude are under control using PI controllers and generating the voltage command for inverter control. Therefore torque and speed ripple could be reduced in comparison with the conventional switching table DTC.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.393-400
• /
• 1992

The DC(Direct-Current) servo motor has widely used for many application areas, FA(Factory Automation), OA(Office Automation) and home applications. But DC servo motor needs periodical inspection because it has brush and commutator. Recently, AC servo motor has expanded it's application areas due to for the development of the power semi-conductor and control technology. But it has large torque ripple for it's small number of commutation. And it also has cogging torque due to permanent magenet rotor. Therefore it can't run balence rotarion. Many torque ripple reduction methods are published. In this paper, phase advanced method adopted for torque ripple reduction of AC servo motor. In this research, AC servo motor torque characteristic variation surveied under the phase advance control through the computer simulation. Under the simulation, the load inertia varied from 0.0001[Kg.m$^{2}$] to 0.0314[Kg.m$^{2}$]. The result os nonlinear simulation, torque and speed ripple of AC servo motor under the phase advance control reduced approximately 50[%] and 10[%]. And maximum torque of AC servo motor under phase advance control condition increased about 5[%] as compare with fixed switching time.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.55-57
• /
• 2007

$CO_2$ laser sees that is most suitable to get this effect through minimum formation damage and advantage that is root enemy of effect that happen in minimum cellular tissue depth of 0.1mm is stable living body organization or internal organs institution. Formation damage by ten can be related in formation's kind or energy density, length of evaporation time. If shorten evaporation time, surroundings cellular thermal damage 200 - because happen within 400ums laser beam in rain focus sacred ground surroundings cellular, tissue without vitiation me by evaporation Poe of very small floor as is clean steam can. Application is possible to vulva cuticle cousins by a paternal aunt quantity, uterine cancer, cuticle tumor by laser system that $CO_2$ laser gets into standard in obstetrics and gynecology application. Because effect that super pulse output is ten enemies of laser if uniformity one pulse durations are short almost is decreased, most of all pulse module special quality of pulse style $CO_2$ laser for obstetrics and gynecology mode stabilization by weight very, in this research to get into short pulse duration and higher frequency density, do switching by high frequency in DC-DC Converter output DC's ripple high frequency to be changed, high frequency done current ripple amount of condenser for output filter greatly reduce can. Ripple of output approximately to Zero realization applying possible inductor realization through a special quality experiment do.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.503-510
• /
• 2014

This study proposes a bi-directional interleaved current-fed resonant converter (CRC) with reduced size of the output filter for a fuel cell electric vehicle. The proposed CRC achieves zero-current switching turn on and off of switches and diodes and makes ripple current of the output capacitor theoretically zero. As a result, the cost and volume of the output capacitor are significantly reduced. The two-stage power conversion technique is also applied for wide input and output voltage range operations. A 2kW prototype of the proposed converter is built and tested to verify the validity of the proposed operation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.4
• /
• pp.375-387
• /
• 2015

This study investigates an economic and highly efficient power-converter topology and its modulation scheme for 60 kW rapid EV charger system. The target system is a three-phase three-switch buck-type rectifier topology. A new carrier-based PWM scheme, which is characterized by simple implementation using logic gates, is introduced in this paper. This PWM scheme replaces the diode rectifier equivalent switching state with an active switching state to produce the same effective current flowing path. As a result, the distortion of input current during the polarity reversal of capacitor line voltage can be mitigated. The proposed modulation technique is confirmed through simulation verification. The proposed modulation technique and its implementation scheme can expand the operation range of the three-phase three-switch buck-type rectifier with high-quality AC input and capacitor ripple current.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.10-14
• /
• 1990

Variable Structure System(VSS) la being extended to a new control system of ac servo machines for its merits of simple mechanism and robustness. This paper has studied about applying VSS to position control for brushless servo motor. But VSS has the chattering problem of control input. This chattering phenomenon cause acoustic noises, torque ripple and increase harmonics of the current. One of the useful way to eliminate this defect of VSS, linearlizing the switching function is discussed here. Though the conventional method of linearizing the switching function diminishes the chattering, it may degrade the robustness of the system. In this paper, new linearized switching function which shows robust performance to the parametric variation and reduces chattering simultaneously is introduced and assured by simulation.