• Journal of Information Display
• /
• v.7 no.1
• /
• pp.12-18
• /
• 2006

We investigated the horizontal alignment properties such as surface morphology, pretilt angle, and polar and azimuthal anchoring energy of organic alignment material-coated surface treated by ion beam. In this investigation the energy and incident angle of ion beam were changed. We also fabricated an in-plane switching (IPS) cell by ion beam alignment. The results showed similar voltage-transmittance characteristics to those of a rubbed cell and better dark state.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.458-463
• /
• 2000

This paper presents a design of the controller for vehicle lateral dynamics using active yaw moment. Vehicle lateral motion is incorporated with directional controllability and stability. These are conflicting each other from the view of vehicle handling performance. To compromise the trade-off between these two aspects, we suggest a new control algorithm based on the sliding mode with time-varying switching surface according to the body side slip angle. The controller can deal with the nonlinear region in vehicle driving and be robust to the parameter uncertainties in the plant model. Control performance was evaluated from the simulation.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.1
• /
• pp.52-57
• /
• 1987

In this paper, a methodology is developed to remove the reaching phase and the high frequency chattering phenomenon which are the common drawbacks of variable structrue control (VSC) system. A time varying switching surface is proposed to achieve sliding motion during the entire control process and a continuous control law whose terms are continuous functions inside a boundary layer neighbouring the time varying switching surface is developed to remove the high frequency chattering phenomenon of VSC. The methodology developed in this paper is applied to the 2'nd order time varying system and the simulated results are compared with those of typical VSC methodology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.169-172
• /
• 2002

The voltage holding ratio(VHR) and the residual DC property in the in-plane switching (IPS) cells on a polyimide surface was studied. Several IPS cells which have different concentrations of cyano liquid crystals (LCs) were fabricated. We found that the VHR of the IPS cell was decreased with increasing concentration of cyano LCs. Also, the VHR of the IPS cell was increased with increasing specific resistivity of fluorine LCs. The residual DC voltage of the IPS cell by capacitance-voltage (C-V) hysteresis method was decreased with increasing concentration of cyano LCs. The residual DC property of the IPS cell on the rubbed PI surface can be improved by high polarity of cyano LC.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.8
• /
• pp.616-622
• /
• 2003

This paper deals with the problem of estimating the asymptotic stability region(ASR) of uncertain variable structure systems with bounded controllers. Using linear matrix inequalities(LMIs) we estimate the ASR and show the exponential stability of the closed-loop control system in the estimated ASR. We give a simple LMI-based algorithm to get estimates of the ASR. We also give a synthesis algorithm to design a switching surface which will make the estimated ASR big. Finally, we give numerical examples in order to show that our method can give better results than the previous ones for a certain class of uncertain variable structure systems with bounded controllers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.453-454
• /
• 2006

We studied the nematic liquid crystal (NLC) alignment capability by the IB(Ion bean) alignment method on a NDLC(Nitrogen Diamond Like Carbon) as a-C:H thin film. and investigated electro-optical performances of the IBaligned IPS(In plane switching)cell with NDLC surface. A good LC alignment by IB exposure on a NDLC surface was achieved. Monodomain alignment of the IB aligned IPS cell can be observed. The goodelectro-optical (EO) characteristics of the IB aligned IPS cell was observed with oblique IBexposure on the NDLC as a-C:H thin film for 1 min.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.1
• /
• pp.31-37
• /
• 2017

PURPOSE. The purpose of this study was to analyze the influence of the platform switching concept on an implant system and peri-implant bone using three-dimensional finite element analysis. MATERIALS AND METHODS. Two three-dimensional finite element models for wide platform and platform switching were created. In the wide platform model, a wide platform abutment was connected to a wide platform implant. In the platform switching model, the wide platform abutment of the wide platform model was replaced by a regular platform abutment. A contact condition was set between the implant components. A vertical load of 300 N was applied to the crown. The maximum von Mises stress values and displacements of the two models were compared to analyze the biomechanical behavior of the models. RESULTS. In the two models, the stress was mainly concentrated at the bottom of the abutment and the top surface of the implant in both models. However, the von Mises stress values were much higher in the platform switching model in most of the components, except for the bone. The highest von Mises values and stress distribution pattern of the bone were similar in the two models. The components of the platform switching model showed greater displacement than those of the wide platform model. CONCLUSION. Due to the stress concentration generated in the implant and the prosthodontic components of the platform switched implant, the mechanical complications might occur when platform switching concept is used.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.2
• /
• pp.39-47
• /
• 1998

It has been known that variable structure control(VSC) has theoretically powerful control technique of providing fast response, no overshoot, and very robust control with respect to system parameter variations and disturbances. However, the technique has not become more widely extended in the industrial circles because chattering phenomenon which may excite high-frequency unmodelled plant dynamics and damage to system components exists. In this paper, a modified variable structure control(MVSC) is developed to alleviate these problems which are applied to the position control of induction motor. While the conventional VSC makes the structure of the system change with high-frequency switching on the center of the one switching surface, in the MVSC two switching surface are used to establish a sliding sector. The structure of the system will be changed with low-frequency switching. Therefore, the proposed algorithm has the properties of reducing chattering, retaining the benefits achieved in the conventional VSC, and working even under the influences of parameter variations. Experimental results show the effectiveness of the control strategy proposed here for the position control of induction motor.

• Journal of Power Electronics
• /
• v.13 no.2
• /
• pp.250-255
• /
• 2013

This paper proposes an optimal current distribution method of dual-rotor brushless DC machines (DR-BLDCMs) which have inner and outer surface-mounted permanent-magnet rotors. The DR-BLDCM has high power density and high torque density compare to the conventional single rotor BLDCM. To drive the DR-BLDCM, dual 3-phase PWM inverters are required to excite the currents of a dual stator of the DR-BLDCM and an optimal current distribution algorithm is also needed to enhance the system efficiency. In this paper, the copper loss and the switching loss of a DR-BLDCM drive system are analyzed according to the motor parameters and the switching frequency. Moreover, the optimal current distribution method is proposed to minimize the total electrical loss. The validity of the proposed method was verified through several experiments.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.171-174
• /
• 1991

Among the various PWM methods, the hysteresis-band current control PWM method is popularly used because of its simplicity of implementation, fast response characteristics and inherent peak current limiting capability. However, the current control PWM method with a fixed hysteresis-band has the disadvantage that switching frequency decreases and current ripple is high as the increasing of back-EMF. As a result, load current contains excess harmonics. This paper describes a adaptive hysteresis-bandwidth control algorithm so as to maintain the average switching frequency constant and decrease the current ripple where the hysteresis bandwidth is derived as a relation with the switching frequency. This control algorithm is applied to the surface-type brushless DC motor with separated winding and using the computer simulation, the validity of its algorithm is proved.