• 한국세라믹학회지
• /
• 제43권12호
• /
• pp.781-787
• /
• 2006

NiO-coated YSZ powder was prepared using heterogeneous precipitation of Ni hydroxides on YSZ particle surface and high energy milling. The powders were characterized by TG/DTA, XRD, XPS, and SEM. Amorphous Ni precipitate completely decomposed into NiO at $500^{\circ}C$ and the growth of NiO crystallites was constrained by the core particles. Nanocrystalline NiO-coated YSZ core-shell structure powder could be obtained after calcination at $800^{\circ}C$ for 2 h. A core-shell powder compact, due to high sinterability, showed a near theoretical density at $1350^{\circ}C$. After reduction at $900^{\circ}C$, interpenetrating Ni-YSZ microstructure with very uniformly distributed fine Ni and YSZ grains and pores was observed. In contrast, the mechanically mixed oxide sample showed less uniform distribution of pores and larger discontinuous We particles as compared with the core-shell samples.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.604-609
• /
• 2016

This study reports on wet-foam stability with respect to porous ceramics from a particle-stabilized colloidal suspension that is achieved through the addition of polymethyl methacrylate (PMMA) using a wet process. To stabilize the wet foam, an initial colloidal suspension of $Al_2O_3$ was partially hydrophobized by the surfactant propyl gallate (2 wt.%) and $SiO_2$ was added as a stabilizer. The influence of the PMMA content on the bubble size, pore size, and pore distribution in terms of the contact angle, surface tension, adsorption free energy, and Laplace pressure are described in this paper. The results show a wet-foam stability of more than 83%, which corresponds to a particle free energy of $2.7{\times}10^{-12}J$ and a pressure difference of 61.1 mPa for colloidal particles with 20 wt.% of PMMA beads. It was possible to control the uniform distribution of the open/closed pores by increasing the PMMA content and by adding thick struts, leading to the achievement of a higher-stability wet foam for use in porous ceramics.

• 한국세라믹학회지
• /
• 제54권6호
• /
• pp.511-517
• /
• 2017

With different working pressures and substrate biases, Cr-Al-N coatings were deposited by hybrid physical vapor deposition (PVD) method, consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) processes. Cr and Al targets were used for the arc ion plating and the sputtering process, respectively. Phase analysis, and composition, binding energy, and microstructural analyses were performed using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FESEM), respectively. Surface droplet size of Cr-Al-N coatings was found to decrease with increasing substrate bias. A decrease of the deposition rate of Cr-Al-N films was expected due to the increase of substrate bias. The coatings were grown with textured CrN phase and (111), (200), and (220) planes. X-ray diffraction data show that all Cr-Al-N coatings shifted to lower diffraction angles due to the addition of Al. The XPS results were used to determine the $Cr_2N$, CrN, and (Cr,Al)N binding energies. The compositions of the Cr-Al-N films were measured by XPS to be Cr 23.2~36.9 at%, Al 30.1~40.3 at%, and N 31.3~38.6 at%.

• Computers and Concrete
• /
• 제2권1호
• /
• pp.79-96
• /
• 2005

The use of high-strength concrete (HSC) has significantly increased over the last decade, especially in offshore structures, long-span bridges, and tall buildings. The behavior of such concrete is noticeably different from that of normal-strength concrete (NSC) due to its different microstructure and mode of failure. In particular, the shear capacity of structural members made of HSC is a concern and must be carefully evaluated. The shear fracture surface in HSC members is usually trans-granular (propagates across coarse aggregates) and is therefore smoother than that in NSC members, which reduces the effect of shear transfer mechanisms through aggregate interlock across cracks, thus reducing the ultimate shear strength. Current code provisions for shear design are mainly based on experimental results obtained on NSC members having compressive strength of up to 50MPa. The validity of such methods to calculate the shear strength of HSC members is still questionable. In this study, a new approach based on artificial neural networks (ANNs) was used to predict the shear capacity of NSC and HSC beams without shear reinforcement. Shear capacities predicted by the ANN model were compared to those of five other methods commonly used in shear investigations: the ACI method, the CSA simplified method, Response 2000, Eurocode-2, and Zsutty's method. A sensitivity analysis was conducted to evaluate the ability of ANNs to capture the effect of main shear design parameters (concrete compressive strength, amount of longitudinal reinforcement, beam size, and shear span to depth ratio) on the shear capacity of reinforced NSC and HSC beams. It was found that the ANN model outperformed all other considered methods, providing more accurate results of shear capacity, and better capturing the effect of basic shear design parameters. Therefore, it offers an efficient alternative to evaluate the shear capacity of NSC and HSC members without stirrups.

• 대한기계학회논문집B
• /
• 제39권5호
• /
• pp.449-453
• /
• 2015

최근 표면개질을 통한 젖음성 향상을 위하여, 마이크로와 나노 구조가 계층적(hierarchical)으로 존재하는 표면에 대한 연구가 공학 및 다양한 연구 분야에서 활발하게 진행되고 있다. 계층적구조가 존재하는 표면에서 초친수성(super-hydrophillic)은 대개 물방울(water droplet)의 계면 거동에 의해 그 특성이 확인된다. 따라서, 본 연구에서는 초친수성 표면위에서의 물방울 계면 거동에 대한 실험적 연구를 수행하였다. 포토리소그래피(photo lithography)공정과 건식 식각공정을 이용하여, 정량적으로 표면을 제작하였으며, 실험 표면에서의 계면 거동은 초고속카메라로 가시화하였다. 가시화 자료를 바탕으로, 물방울 계면거동은 표면에 존재하는 마이크로 및 나노구조의 지형학적 특성에 의해 영향을 받음을 확인하였다.

• 한국공작기계학회논문집
• /
• 제17권4호
• /
• pp.42-50
• /
• 2008

Various researches to reduce weight of a vehicle are achieving. One of these researches is tendencious to manufacture the hollow piston rod using friction welding instead of solid one of the vehicle shock absorber. This study deals with the friction welding of SM45C to SM20C-pipe that is used normally in the vehicle shock absorber. The friction time was variable conditions under the conditions of spindle revolution of 2,000rpm, friction pressure of 55MPa, upset pressure of 75MPa, and upset time of 2.0seconds. Under these conditions, the microstructure of weld interface, tensile fracture surface and mechanical tests of friction weld were studied and so the results were as follows. When the friction time was l.5seconds under the conditions, the maximum tensile strength of the friction weld happened to be 837MPa, which is 113% of SM20C's tensile strength and 97% of SM45C's. The optimal welding conditions were n=2,000rpm, $P_1=55MPa$, $P_2=75MPa$, $t_1=1.5sec$, $t_2=2.0sec$ when the total upset length is 1.7mm.

• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.65-70
• /
• 2008

This study deals with the friction welding of SKH55 and SM45C; The friction time was variable conditions under the conditions of spindle revolution 2,000rpm, friction pressure of 190MPa, upset pressure of 270MPa and upset time of 2.0 seconds. Under these conditions, the microstructure of weld interface, tensile fracture surface and mechanical tests were studied, and so the results were as follows. 1. When the friction time is 1.0 seconds, the tensile strength of friction welds was 926MPa, which is around as much as 84% of the tensile strength of base metal(SKH55), the bending strength of friction welds was 1,542MPa, which is around as much as 80% of the bending strength of base metal(SKH55), the shear strength of friction welds was 519MPa, which is around as much as 70% of the shear strength of base metal(SKH55). 2 According to the hardness test, the hardness distribution of the weld interface was formed from 964Hv to 254Hv. HAZ(Heat Affected Zone) was formed from the weld interface to 1.5mm of SKH55 and 2mm of SM45C.

• Journal of Ginseng Research
• /
• 제19권1호
• /
• pp.62-72
• /
• 1995

During the controlled atmosphere storage (CA), fresh ginseng showed good appearance in quality, and other deterioration of freshness was not observed until 12 weeks. On the other hand, MA storage had kept freshness only in treatment of 1 until 8 weeks. There was no significant difference between treated and non-treated sample with preservatives, and not treated sample was not infected with various different fungi. Moisture contents and hardness of ginseng in all treatments were not changed much until 12 weeks, and surface shrinkage did not occur either. But shear stress increased somewhat in all treatments after 12 weeks. The granule of microstructure in tissue diminished slightly. The apparent Quality of red ginseng was good until 4 weeks of treatment. But as time passed, white skin and wrinkled skin were generated and darkened in its color. B-1 in CA and E-1 in MA were found to be the most favorable one. The content of crude saponin did not change significantly during storage of CA or MA by preservation conditions and period. Though a small increase in saponin content from 4.92% to 5.43% was recognized in B-1, which was treated with preservative and 6.0% In B-2, control, this could rather explain increment of soluble component by butanol. Thus, there was no change in total contents of ginsenoside pattern and composition of each content. The Rbl content in B-1 and B-2 were 0.98%, and 0.97%, respectively, whereas that of control was 0.96%. E-1 of MA, treated with preservative was 5.32% after 12 weeks, but was 5.73% in control, indicating that ginsenosides pattern was quite similar to that of CA storage.

• 한국식품과학회지
• /
• 제41권4호
• /
• pp.369-373
• /
• 2009

전분액화에 호화찰옥수수전분가 쌍축형 압출성형의 원료로 직접 사용되었다. 그 액화 효과와 체류시간분포를 분석하였다. 내열성 ${\alpha}$-amylase(Bacillus licheniformis로부터 분리)를 함께 첨가하여 사용하였다. 전분액화는 환원당측정, gel permeation chromatography(GPC), 주사전자현미경을 통하여 분석하였다. 배럴온도와 수분함량이 높을수록 환원당 함량은 증가하였고, 호화전분의 경우 생전분보다 더 많은 환원당이 생성되었다. GPC에서 호화전분의 사용에 의한 저분자화 효과는 뚜렷하지 않았으나, 효소 첨가없이 압출성형하는 경우에는 일부 효과가 있는 것으로 나타났다. 주사전자현미경의 미세구조에서는 호화전분을 쓸 경우 그 표면이 더 불규칙하고 침식되는 것을 관찰할 수 있었다. 종합적으로 호화전분의 사용이 전분액화에 효과가 있음을 알 수 있었다. 체류시간분포에서는 호화전분을 원료로 할 경우 그 분산도가 커지는 것으로 나타났다. 이는 호화전분은 압출성형의 흐름이 원만하지 않은 것을 의미하였으나, 배럴온도와 수분함량을 증가시킴에 따라 그 분산도를 감소시킬 수 있음을 알 수 있었다.

• 한국세라믹학회지
• /
• 제43권11호
• /
• pp.715-723
• /
• 2006

Perovskite oxide materials are very important for the electronics industry, because they exhibit promising properties. With an interest in the obvious applications, significant effort has been invested in the growth of highly crystalline epitaxial perovskite oxide thin films in our laboratory. And the desired structure of films was formed to achieve excellent properties. $Y_1Ba_2Cu_3O_{7-x}$ (YBCO) superconducting thin films were simultaneously deposited on both sides of 3 inch wafer by inverted cylindrical sputtering. Values of microwave surface resistance R$_2$ (75 K, 145 GHz, 0 T) smaller than 100 m$\Omega$ were reached over the whole area of YBCO thin films by pre-seeded a self-template layer. For implementation of voltage tunable high-quality varactor, A tri-layer structured SrTiO$_3$ (STO) thin films with different tetragonal distortion degree was prepared in order to simultaneously achieve a large relative capacitance change and a small dielectric loss. Highly a-axis textured $Ba_{0.65}Sr_{0.35}TiO_3$ (BST65/35) thin films was grown on Pt/Ti/SiO$_2$/Si substrate for monolithic bolometers by introducing $Ba_{0.65}Sr_{0.35}RuO_3$ (BSR65/35) thin films as buffer layer. With the buffer layer, the leakage current density of BST65/35 thin films were greatly reduced, and the pyroelectric coefficient of $7.6\times10_{-7}$ C $cm^{-2}$ $K^{-1}$ was achieved at 6 V/$\mu$m bias and room temperature.