• Journal of Ocean Engineering and Technology
• /
• v.13 no.3 s.33
• /
• pp.12-20
• /
• 1999

In this paper, method for mapping a three-dimensional shape into the two-dimensional plane will be introduced. This method is referred to geometric modelling and means a transformation between the flat sheet and final surface. The initial blank shape represents the original configuration of the final shape formed into three dimensional surface. The initial constant constant area mapping hypothesis was used in this paper. This technique will be applied to the basic data for an interactive computer design capable of dealing with typical stamping process, including deep parts and complex shapes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.2
• /
• pp.58-62
• /
• 2004

The shape evolution of the interface void of copper metallization for intergrated circuits under electromigration stress is modeled. A 2-dimensional finite-difference numerical method is employed for computing time evolution of the void shape driven by surface diffusion, and the electrostatic problem is solved by boundary element method. When the diffusion coefficient is isotropic, the numerical results agree well with the known case of wedge-shape void evolution. The numerical results for the anisotropic diffusion coefficient show that the initially circular void evolves to become a fatal slitlike shape when the electron wind force is large, while the shape becomes non-fatal and circular as the electron wind force decreases. The results indicate that the open circuit failure caused by slit-like void shape is far less probable to be observed for copper metallization under a normal electromigration stress condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.90-95
• /
• 2001

A continuum-based shape design sensitivity analysis (DSA) method is presented for the acoustic radiation from thin body. The normal derivative integral formulation is employed as an analysis formulation and differentiated directly by using material derivative to get the acoustic shape design sensitivity. In the acoustic sensitivity formulation, derivative coefficients of the structural normal velocities on the surface are required as the input. Thus, the shape design sensitivities of structural velocities on the surface with respect to the shape change are also calculated with continuum approach. A simple disk is considered as a numerical example to validate the accuracy and efficiency of the analytical shape design sensitivity equations derived in this research. This research should be very helpful to design an application involving thin body and to change its acoustic characteristics.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.4
• /
• pp.194-202
• /
• 2005

The objective of this paper is to develop a multi-functional hotwire cutting system (MHC) using EPS-foam block or plate as the working material. Because the MHC apparatus employs a four-axis synchronized hotwire cutter with the structure of two XY movable heads and a turntable, it allows the easy fabrication of various 3D shapes, such as (1) an axisymmetric shape or a sweeping cross-sectioned pillar shape using the hot-strip in the form of sweeping surface and EPS foam block on the turntable, (2) a polyhedral complex shape using the hotwire and EPS foam block on the turntable, and (3) a ruled surface approximated freeform shape using the hotwire and EPS foam plate. In order to examine the applicability of the developed MHC apparatus, an axisymmetric shape, a polyhedral shape and a large-sized freeform shape were fabricated on the apparatus.

• Tribology and Lubricants
• /
• v.36 no.4
• /
• pp.193-198
• /
• 2020

Fluid film bearings are among the best devices used for overcoming friction and reducing wear. Surface texturing is a new surface treatment technique used for processing grooves and dimples on the lubricated surface, and it helps to minimize friction further and improve the wear resistance. In several studies, parallel surfaces, such as thrust bearings and mechanical face seals, have been investigated, but most sliding bearings have a convergent film shape. This paper presents the third part of a recent study and focuses on the effect of the groove shape on the lubrication performance of inclined slider bearings, following the two previous papers on the effects of the groove position and depth. We adopted the continuity and Navier - Stokes equations to conduct numerical analyses using FLUENT, which is a commercial computational fluid dynamics code. The groove shape adopted in the numerical analysis is rectangular and triangular, and its depth is varied. The results show that the streamlines, pressure distributions, and groove shape significantly influence the lubrication performance of the inclined slider bearing. For both shapes, the load-carrying capacity (LCC) is maximum near the groove depth, where vortices occur. In the shallow grooves, the LCC of the rectangular shape is higher, but in deeper grooves, that of the triangular shape is higher. The deeper the rectangular groove, the higher the decrease in the frictional force. The results of this study can be used as design data for various sliding bearings.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.800-805
• /
• 2013

Incremental forming of sheet metal is a modern method of forming sheet metal, where parts can be formed without the use of dedicated dies. Existing experimental configurations for incremental forming can be broadly classified into two categories, i.e., negative and positive forming. In this paper, forming qualities such as shape accuracy and surface roughness of Al 1050 material were discussed for different forming methods. The formed and the corresponding opposing surfaces were measured with a three-dimensional scanner and a surface roughness tester. It was found that in terms of shape accuracy, the best opposing surface was obtained with positive forming, whereas the worst formed surface was obtained with negative forming; furthermore, the opposing surface is always better than the formed surface, regardless of the forming method used.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.622-629
• /
• 2006

The shape optimization of blade sweep in a transonic axial compressor rotor of NASA Rotor 37 has been performed using response surface method and the three-dimensional Wavier-Stokes analysis. Two shape variables of the rotor blade, which are used to define the rotor sweep, are introduced to increase the adiabatic efficiency of the compressor. Throughout the optimization, optimal shape having a backward sweep is obtained. Adiabatic efficiency, which is the objective function of the present optimization, is successfully increased. Separation line due to the interference between a shock and surface boundary layer on the blade suction surface is moved downstream for the optimized blade compared to the reference one. The increase in adiabatic efficiency for the optimized blade is caused by suppression of the separation due to a shock on the blade suction surface.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.268-275
• /
• 1999

The purpose of this study is to propose the method of determining the initial pneumatic membrane structures surface and stresses and displacements. Tension structure such as pneumatic membrane structures is stabilized by their initial prestress and air pressure. The process to find initial structural overall shape of tension structures produced by initial prestress called shape finding. One of the most important factor for the design of membrane structures is to search initial smooth surface, because unlike steel or concrete building elements which resist loads in bending, all tension structure forces are carried within the surface by membrane stress. The result for initial surface of pneumatic membrane element and maximum displacement in large deformation in analysis is compared with well-known nonlinear numerical method such as Newton-raphson method and dynamic relaxation method

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.3
• /
• pp.95-108
• /
• 1993

The needs for smooth curves and surfaces are increasing in modeling cars, ships, airplanes, and other consumer products either for aesthetic or functional purpose. However, the curves and surfaces generated by conventional modeling methods usually exhibit an unwanted behavior due to digitizing errors or inadequate generation method, and thus much time and extra effort is spent afterwards to get the faired results. The objective of this work is to develop a fairing scheme by which well refined shape of a surface can be acquired with detecting and removing the shape imperfections of the given surface represented by NURBS. The fairing scheme is based on an optimization process in which the control points of the given surface are repositioned to minimize the integration of the jumps(perturbations) of the unit normal vectors at all surface points.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.7
• /
• pp.1633-1641
• /
• 1996

In this paper we propose a new method for anlayzing the properties of surface reflectance and reconstructing the shape of object using estimated reflectance parameters. We have investigated the hybrid reflectance surface which has specularreflection and diffuse reflection, which can be explained by Torrance-Sparrow model. Sample sphere made on one maerial is used to estimate the reflectance properties by using LMS algorithm. We can make the reference image which consists of surface normal and brightness value using estimated reflectance parameters, and thenarbitrary shape object made of the same material as sample can be reconstructed by matching with reference image. Photometric matching method proposed in this paper is robust because it mateches object image with the reference imageconsidering its neighbor brightness distribution. Also, in this paper plate diffuse illumination is used to remove intensity disparity with simple scheme. It is expected that the proposed algorithm can be applied to 3D recognition, vision inspection system and other fields.