• Corrosion Science and Technology
• /
• v.21 no.6
• /
• pp.495-502
• /
• 2022

Anodization is a representative electrochemical surface treatment method that can improve both heat resistance and corrosion resistance by forming an anodization film on the surface of the aluminum. However, these properties can be changed after an additional heat treatment process. In this study, Al 6061 was subjected to an anodization process at 60 V for 1 hour, 5 hours, or 9 hours. An additional heat treatment process was performed at 500 ℃ for 30 minutes. Field emission scanning electron microscopy (FE-SEM) analysis revealed that the thickness of the anodized film was increased in proportion to the anodization time. Both pore size and pore diameter of the anodized film was also increased after anodization. After an additional heat treatment process, there were no significant changes in the thickness, pore size, or pore diameter of the anodized film. Heat resistance was confirmed through thermal analysis and chemical resistance was evaluated with a potentiodynamic polarization test.

• Journal of Biomedical Engineering Research
• /
• v.22 no.6
• /
• pp.519-526
• /
• 2001

At present. about 0.3 million and more THRs (Total Hip Replacement) in a rear are being done worldwide. The increase in mechanical failure with the increase in THR, required more revisions. Revisions compensate mainly the wear of the artificial joint frictional surface and the loosening of the cup and stem. According to recent researches, loosening is mainly due to wear debris UHMWPE (Ultra High Molecular Weight Polyethylene) from frictional surfaces . To overcome the wear problems associated with artificial joint materials , new surface structures with regular Patterns were designed and fabricated The lubrication Properties were examined to evaluate the wear of the frictional surfaces. The surface structure manifested a Pattern of "dents" with a 0.2-1.0 mm of diameter and 0.6-2.0 mm of Pitch. From the friction test of the SUS316L vs UHMWPE using the frictional tester, we found that the lubrication Performance was improved due to of drastically reduced amount of abrasion. There were optimum sizes for the diameter and the pitch of the Pattern. The results demonstrated that the lubrication properties could be improved by Patterning of the frictional surfaces. The surface Patterning was effective in preventing wear of the frictional surfaces, and the life of an artificial joint could be extended with such Patterning.

• Journal of Power System Engineering
• /
• v.5 no.4
• /
• pp.67-73
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of two-stage shot peening iud single-stage shot peening for two kinds of spring steel(SUP7, SAE9254). This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from decreasing the surface roughness unchanging the surface hardness increasing the compressive residual stress. Results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.71-79
• /
• 2001

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel(JISG4081-SUP ,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.185-192
• /
• 2003

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to Dow the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7, SAE 9254, DON 50CrV4) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of hish hardness.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.366-372
• /
• 2002

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface deject as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to know tile influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7,SAE 9254, DIN 50CrV4, ) are made. This study shows the outstanding improvement of fatigue properties at tire case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of high hardness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05b
• /
• pp.11-14
• /
• 2004

In this paper, the effect of adhesion properties of semiconductive-insulating interface layer of silicone rubber on electrical properties was investigated. The modifications produced on the silicone surface by oxygen plasma were accessed using ATR-FTIR, contact angle and AFM. Adhesion was obtained from T-peel tests of semiconductive layer having different treatment durations. In addition, ac breakdown test was carried out for elucidating the change of electrical property with duration of plasma treatment. From the results, the treatment in the oxygen plasma produced a noticeable increase in surface energy, which can be mainly ascribed to the the creation of O-H and C=O. It is observed that adhesion performance was determined by not surface energy but roughness level of silicone surface. It is found that ac dielectric strength was increased with improving the adhesion between the semiconductive and insulating interface.

• Journal of the Korean Society of Tobacco Science
• /
• v.18 no.1
• /
• pp.85-91
• /
• 1996

Commercially available activated carbon was treated with 0.2N NaOH/0.1N HCl to decrease the ash contents and to analyze the effect of demineralization. We have studied their properties and adsorptivity to solvents such as benzene, acetone, toluene and carbon tetrachloride, ammonia and also aldehydes of cigarette smoke. By demineralization with NaOH/HCl, surface area and pore volume were increased up to 10 - 20% according to developement of micro-pore and pH of activated carbon was also changed from 10.2 to 6.3. Surface acidity of the activated carbon treated with chemicals increased slightly. The chemical treatment led to small increase in adsorptioil properties of solvents, ammonia and aldehydes of cigarette smoke, but content of chlorine and sulfur in activated carbon were reduced. As the results of smoking test, charcoal taste caused by the activated carbon was reduced significantly by the treatment with NaOH/HCl.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.89-92
• /
• 2005

This study investigates influence of particle properties of crushed sand on the duality of concrete. The test shows that an increase of fineness modulus(FM) resulted in high slump and air contents, while compressive strength decreased due to decreased adhesion with reduction of surface area. As grain shape become rounder, the slump of concrete increased, due to reduction of internal friction, and increased air contents. The reduction of adhesion by abrasion of surface declined compressive strength during the process of manufacturing crushed sand. Increase of powder contents decreased slump and it also decreased air contents due to the effect of filling air void. In addition. using powder contents increased compressive strength, but could not find any difference of bleeding and tensile strength with particle properties.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.23 no.2
• /
• pp.25-43
• /
• 2005

Generally, machine calendering are used change of paper surface properties. During machine calendering, dry paper passes between the rolls under pressure, thereby improving the surface smoothness and gloss. These improvements make the paper better suited for printing and decreasing problems during the printing, such as delayed dry and set-off. Then we investigated newspaper properties by the changing of machine calendering condition, and relationship printability. Properties of each samples were examined in accordance with KS and TAPPI standard test method i.e, basic weight, bulk density, thickness, porosity, opacity, brightness, smoothness and roughness. IGT printability tester was used to obtain ink requirement of newspaper, printed density and set-off. Results of in this study, we have proposed the optimizes range of newspaper calendering condition. Useful optimize calendering condition was pressure 55 kN/m, temperature $130^{\circ}C$.