• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.308-309
• /
• 2016

Reducing surface recombination is a critical factor for high efficiency silicon solar cells. The passivation process is for reducing dangling bonds which are carrier. Tunnel oxide layer is one of main issues to achieve a good passivation between silicon wafer and emitter layer. Many research use wet-chemical oxidation or thermally grown which the highest conversion efficiencies have been reported so far. In this study, we deposit ultra-thin tunnel oxide layer by PECVD (Plasma Enhanced Chemical Vapor Deposition) using $N_2O$ plasma. Both side deposit tunnel oxide layer in different RF-power and phosphorus doped a-Si:H layer. After deposit, samples are annealed at $850^{\circ}C$ for 1 hour in $N_2$ gas atmosphere. After annealing, samples are measured lifetime and implied Voc (iVoc) by QSSPC (Quasi-Steady-State Photo Conductance). After measure, samples are annealed at $400^{\circ}C$ for 30 minute in $Ar/H_2$ gas atmosphere and then measure again lifetime and implied VOC. The lifetime is increase after all process also implied VOC. The highest results are lifetime $762{\mu}s$, implied Voc 733 mV at RF-power 200 W. The results of C-V measurement shows that Dit is increase when RF-power increase. Using this optimized tunnel oxide layer is attributed to increase iVoc. As a consequence, the cell efficiency is increased such as tunnel mechanism based solar cell application.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.418.2-418.2
• /
• 2016

$Al_2O_3$ passivation layer has excellent passivation properties at p-type Si surface. This $Al_2O_3$ layer forms thin $SiO_2$ layer at the interface. There were some studies about inserting thermal oxidation process to replace naturally grown oxide during $Al_2O_3$ deposition. They showed improving passivation properties. However, thermal oxidation process has disadvantage of expensive equipment and difficult control of thin layer formation. Wet chemical oxidation has advantages of low cost and easy thin oxide formation. In this study, $Al_2O_3$/$SiO_2/Si(100)$ interface was formed by wet chemical oxidation and PA-ALD process. $SiO_2$ layer at Si wafer was formed by $HCl/H_2O_2$, $H_2SO_4/H_2O_2$ and $HNO_3$, respectively. 20nm $Al_2O_3$ layer on $SiO_2/Si$ was deposited by PA-ALD. This $Al_2O_3/SiO_2/Si(100)$ interface were characterized by capacitance-voltage characteristics and quasi-steady-state photoconductance decay method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.28-30
• /
• 2009

이종접합태양전지에서 p a-Si:H/c-Si의 p a-Si:H의 증착 조건인 $H_2/SiH_4$ 비율, $B_2H_6$의 농도를 변화 시키며 실험하여 이 따라 계면 특성 변화를 연구하였다. pa-Si:H의 $H_2/SiH_4$ 비율이 상승할수록 carrier lifetime이 증가하다 다시 감소하는 경향을 나타내었다. 이는 $H_2/SiH_4$의 비율 중 효과적으로 웨이퍼표면을 효과적으로 passivation하는 지점이 있는 것으로 보인다. $B_2H_6$의 농도는 상승할수록 carrier lifetime이 줄어드는 경향을 보였다. $B_2H_6$에서 농도가 올라감에 웨이퍼 표면의 defect로 작용했을 것으로 생각된다. 이에서 몇몇의 조건으로 태양전지를 제작한 결과 $H_2/SiH_4$ 비율에 따라서는 carrier lifetime은 효율에 그 영향이 미미한 것으로 조사되었고, $B_2H_6$의 농도가 낮을수록 개방전압은 상승하는 결과를 얻어 도핑 농도가 효율에 직접적인 형향을 주는 것으로 나타났다.

• 조명전기설비학회논문지
• /
• 제13권4호
• /
• pp.87-95
• /
• 1999

새로운 종류의 고체상태 대전력, 고속전자장치 즉 광전도전력스위치(PCPS)의 가장 큰 문제점은 평균전계하의 표면에서 스위치 섬락의 대부분이 반도체의 벌크파괴보다 낮다는 것이다. 이러한 문제를 극복하고 고밀도 고체 전력 스위치에 사용할 수 있는 유일한 방법이 고체 절연물로 표면을 페시베이션(Passivation)하는 것이다. 본 실험에서 Silicon의 절연내력은 진공중에서 10[kV/cm]에서 심하게 열화되어졌고, 기중에서 30[kV/cm], SF6에서 80∼90[kV/cm]으로 개선되지만, 스위치의 주 응용이 진공 또는 우주에서 사용되기 때문에 이러한 현상은 매우 심각한 문제이다. 페시베이션후 소자들은 진공과 기중에서 언페시베이션된 소자가 SF6내에서 얻을 수 있는 만큼의 높은 파괴값을 가졌다. 이러한 결과로 볼 때 페시베이션된 소자들이 매우 우수한 파괴값을 가진다는 것을 알 수 있다. 본 논문은 고전계 하에서 페시베이션 전·후 실리콘 파괴의 주 특성과 메커니즘에 대해 밝혔다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.276-279
• /
• 2004

Plasma enhanced chemical vapor deposition (PECVD) of silicon nitride (SiN) is a proven technique for obtaining layers that meet the needs of surface passivation and anti-reflection coating. In addition, the deposition process appears to provoke bulk passivation as well due to diffusion of atomic hydrogen. This bulk passivation is an important advantage of PECVD deposition when compared to the conventional CVD techniques. A further advantage of PECVD is that the process takes place at a relatively low temperature of 300t, keeping the total thermal budget of the cell processing to a minimum. In this work SiN deposition was performed using a horizontal PECVD reactor system consisting of a long horizontal quartz tube that was radiantly heated. Special and long rectangular graphite plates served as both the electrodes to establish the plasma and holders of the wafers. The electrode configuration was designed to provide a uniform plasma environment for each wafer and to ensure the film uniformity. These horizontally oriented graphite electrodes were stacked parallel to one another, side by side, with alternating plates serving as power and ground electrodes for the RF power supply. The plasma was formed in the space between each pair of plates. Also this paper deals with the fabrication of multicrystalline silicon solar cells with PECVD SiN layers combined with high-throughput screen printing and RTP firing. Using this sequence we were able to obtain solar cells with an efficiency of 14% for polished multi crystalline Si wafers of size 125 m square.

• 한국전기전자재료학회논문지
• /
• 제36권3호
• /
• pp.233-240
• /
• 2023

p-type Tunnel Oxide Passivating Contacts (TOPCon) solar cell is fabricated with a poly-Si/SiO_x structure. It simultaneously achieves surface passivation and enhances the carriers' selective collection, which is a promising technology for conventional solar cells. The quality of passivation is depended on the quality of the tunnel oxide layer at the interface with the c-Si wafer, which is affected by the bond of SiO formed during the subsequent annealing process. The highest cell efficiency reported to date for the laboratory scale has increased to 26.1%, fabricated by the Institute for Solar Energy Research. The cells used a p-type float zone silicon with an interdigitated back contact (IBC) structure that fabricates poly-Si and SiO_x layer achieves the highest implied open-circuit voltage (iV_oc) is 750 mV, and the highest level of edge passivation is 40%. This review presents an overview of p-type TOPCon technologies, including the ultra-thin silicon oxide layer (SiO_x) and poly-silicon layer (poly-Si), as well as the advancement of the SiO_x and poly-Si layers. Subsequently, the limitations of improving efficiency are discussed in detail. Consequently, it is expected to provide a basis for the simplification of industrial mass production.

• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.332-340
• /
• 2023

Crystalline silicon solar cells have attracted great attention for their various advantages, such as the availability of raw materials, high-efficiency potential, and well-established processing sequence. Tunnel oxide passivated contact (TOPCon) solar cells are widely regarded as one of the most prospective candidates for the next generation of high-performance solar cells because an efficiency of 26% has been achieved in small-area solar cells. Compared to n-type TOPCon solar cells, the photo conversion efficiency (PCE) of p-type TOPCon is slightly higher. The highest PCEs of p-type TOPCon and n-type TOPCon solar cells are 26.0% and 25.8%, respectively. Despite the highest efficiency in small-area cells, limited progress has been achieved in p-type TOPCon solar cells for large are due to their lower carrier lifetime and inferior surface passivation with the boron-doped c-Si wafer. Nevertheless, it is of great importance to promoting the p-type TOPCon technology due to its lower price and well-established manufacturing procedures with slight modifications in the PERC solar cells production lines. The progress in different approaches to increase the efficiencies of p-type TOPCon solar cells has been reported in this review article and is expected to set valuable strategies to promote the passivation technology of p-type TOPCon, which could further increase the efficiency of TOPCon solar cells.

• Applied Science and Convergence Technology
• /
• 제26권4호
• /
• pp.62-65
• /
• 2017

Passivation of surface defects by the formation of chemically inert structure at the surface of $TiO_2$ nanocrystals can be potentially useful in enhancing their photocatalytic activity. In this regard, we have studied the surface chemical states of $TiO_2$ surfaces prepared by a treatment in the afterglow of $N_2$ microwave plasma using X-ray photoemission spectroscopy (XPS). We find that nitrogen is incorporated into the surface after the treatment up to a few atomic percent. Interestingly, the surface oxynitride layer is found to be chemically stable when it's in contact with water at room temperature (RT). The surface nitrogen species were also found to be thermally stable upon annealing up to $150^{\circ}C$ in the atmospheric pressure. Thus, we conclude that the treatment of oxide materials such as $TiO_2$ in the afterglow of $N_2$ plasma can be effective way to passivate the surface with nitrogen species.

• Transactions on Electrical and Electronic Materials
• /
• 제16권5호
• /
• pp.285-289
• /
• 2015

We prepared silver Schottky contacts to O-polar and nonpolar m-plane bulk ZnO wafers. Then, by considering various transport models, we performed a comparative analysis of the current transport properties of Ag/bulk ZnO Schottky diodes, which were measured at 300, 200, and 100 K. The fitting of the forward bias current-voltage (I-V) characteristics revealed that the tunneling current is dominant as the transport component in both the samples. Compared to thermionic emission (TE), a stronger contribution of tunneling current was observed at low temperature. The reverse bias I-V characteristics were well fitted with the thermionic field emission (TFE) in both the samples. The presence of acceptor-like adsorbates, such as O₂ and H₂O, modulated the surface conductive state of ZnO, thereby affecting the tunneling effect. The degree of activation/passivation of acceptor-like adsorbates might be different in both the samples owing to their different surface morphologies and surface defects (e.g., oxygen vacancies).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.42-42
• /
• 2010

We have characterized the previously undescribed parameters for engineering the electrical properties of single-walled carbon nanotube (SWCNT) films for technological applications. The surface tension of the top coating passivation material and matching coefficients of thermal expansion for the substrate and carbon nanotube network are two crucial parameters for the fabrication of reliable and highly conductive single-walled carbon nanotube network thin films.