• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.424-430
• /
• 2021

Determining the cause of a traffic signal violation is difficult if the drivers' claims are contradictory. In this study, the process of identifying signal violations using a simulation was presented based on cases. First, statements from the driver or witness whose cause of the signal violation is unclear were excluded. Second, the final position, final location, damaged area, steering status, braking status, and road surface traces of the vehicle were collected. The impact point was investigated from the stop line. Third, simulation data were modified and entered until the collision situation of the accident vehicle and the final stop position were met. Fourth, if the simulation results were consistent with the crash situation, the facts were verified by cross-validation to conform to the driver's statement. The results of the simulation showed that the Lexus entered the left turn signal in the intersection at approximately 55 km/h. In comparison, the Sonata driver saw the vehicle straight ahead at the intersection, entered the 72 km/h intersection, and collided with the Lexus. Therefore, the Sonata was identified as a signal violation, and the claims of the Sonata driver, witnesses, and police were contradictory.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.4
• /
• pp.165-172
• /
• 2014

When a vehicle is running on the road, the surface conditions and environment of road by reason of insufficient road design standards is so greatly that have an effect on drivers. In particular, the road design of the past is conducted empirical and ideal judgment, but recently, the new technical development is attempted that three and four dimensional parameters is reconsidering and adjusting at the same time. In this study, we analyzed the vehicle behavior characteristics according to the change of driving speed and vertical grades on braking at the peak point of the frozen road by using a PC-crash program for traffic accident reconstruction. As a result, we were conformed the fact that the friction coefficient of road surface and the vehicle speed is affected by vehicle behavior characteristics for intersection vertical grades and were showed the feasibility of verification through a simulation in order to solve the problem of road design in advance.

• KIEAE Journal
• /
• v.16 no.1
• /
• pp.89-94
• /
• 2016

This study is part of three-dimensional(3D) heat transfer analysis program developmental process. The program is being developed without it's own built in 3D-modeller. So 3D-model must be created from another 3D-modeller such as generic CAD programs and imported to the developed program. After that, according to the 3D-geometric data form imported model, 3D-mesh created for numerical calculation. But the 3D-model created from another 3D-modeller is likely to have errors in it's geometric data such as mismatch of position between vertexes or surfaces. these errors make it difficult to create 3D-mesh for calculation. These errors are must be detected and cured in the pre-process before creating 3D-mesh. So, in this study four kinds of filters and functions are developed and tested. Firstly, 'vertex error filter' is developed for detecting and curing for position data errors between vertexes. Secondly, 'normal vector error filter' is developed for errors of surface's normal vector in 3D-model. Thirdly, 'intersection filter' is developed for extracting and creating intersection surface between adjacent objects. fourthly, 'polygon-line filter' is developed for indicating outlines of object in 3D-model. the developed filters and functions were tested on several shapes of 3D-models. and confirmed applicability. these developed filters and functions will be applied to the developed program and tested and modified continuously for less errors and more accuracy.

• Applied Microscopy
• /
• v.45 no.3
• /
• pp.155-169
• /
• 2015

Plastic deformation was introduced to the austenitic (${\gamma}$) stainless steel of SS304 by air blast shot peening, ultrasonic shot peening, and ultrasonic nanocrystalline surface modification. Various deformation structures were formed. The hardness, the deformation structure and the underlying grain refinement mechanism were investigated. In the deformed region, planar dislocation arrays and deformation twin (DT), the DT-DT intersection and ${\varepsilon}$-martensite structures, and ${\alpha}^{\prime}$-martensite were formed in the respective regions of low, medium, and high strain. The grain refinement mechanism is found to be closely related to the 1) sub-division of coarse grains by DT, shear bands and their intersection, and 2) formation of nano-sized ${\alpha}^{\prime}$-martensite due to the high plastic deformation.

• Steel and Composite Structures
• /
• v.21 no.5
• /
• pp.1017-1029
• /
• 2016

When a welded circular hollow section (CHS) tubular joint is subjected to brace axial loading, failure position is located usually at the weld toe on the chord surface due to the weak flexural stiffness of the thin-walled chord. The failure mode is local yielding or buckling in most cases for a tubular joint subjected to axial load at the brace end. Especially when a cyclic axial load is applied, fracture failure at the weld toe may occur because both high stress concentration and welding residual stress along the brace/chord intersection cause the material in this region to become brittle. To improve the ductility as well as to increase the static strength, a tubular joint can be reinforced by increasing the chord thickness locally near the brace/chord intersection. Both experimental investigation and finite element analysis have been carried out to study the hysteretic behaviour of the reinforced tubular joint. In the experimental study, the hysteretic performance of two full-scale circular tubular T-joints subjected to cyclic load in the axial direction of the brace was investigated. The two specimens include a reinforced specimen by increasing the wall thickness of the chord locally at the brace/chord intersection and a corresponding un-reinforced specimen. The hysteretic loops are obtained from the measured load-displacement curves. Based on the hysteretic curves, it is found that the reinforced specimen is more ductile than the un-reinforced one because no fracture failure is observed after experiencing similar loading cycles. The area enclosed by the hysteretic curves of the reinforced specimen is much bigger, which shows that more energy can be dissipated by the reinforced specimen to indicate the advantage of the reinforcing method in resisting seismic action. Additionally, finite element analysis is carried out to study the effect of the thickness and the length of the reinforced chord segment on the hysteretic behaviour of CHS tubular T-joints. The optimized reinforcing method is recommended for design purposes.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.115-123
• /
• 2011

This study was conducted to investigate the early-age behavior and performance of precast pavements constructed by replacing existing asphalt pavements for an intersection in urban bus only lanes. The monitoring items included level differences between asphalt pavement and precast panels at the beginning and ending locations of the precast pavement, level differences and joint widths between precast panels, precast panel settlement, and skid resistance of the panel surface. At a certain time after the construction, the diamond grinding method was applied and its effect was also investigated. The monitoring results showed that as time went by, the panel level, joint width, settlement, and skid resistance were not much varied. That implied the stable sustaining of external loads by the precast pavements. In addition, it was verified that employing diamond grinding could reduce the level differences between precast panels.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.514-521
• /
• 2021

When calculating an intersection collision speed using a formula, it is very difficult to grasp the degree of deceleration of a vehicle after the collision unless there is road surface trace in the entire section where each vehicle moved from the point of collision to their final positions after the collision. A vehicle's motion trajectory shows an irregular curve after a collision due to the effects of inertia based on the driving characteristics of the vehicle, the eccentric force according to the collision site, and the collision speed. Therefore, it is very important to set the appropriate departure angle after a collision for accurate collision speed analysis. In this study, based on experimental collision data using a computer simulation (PC-Crash), the correlation between an appropriate vehicle departure angle and the post-collision speed was analyzed, and then, a regression analysis model was derived. Through this, we propose a method to calculate collision speed by applying only the vehicle departure angle in some types of collisions for traffic accidents at intersections.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.237-240
• /
• 2003

Gas turbines are extensively used in flight propulsion, electrical power generation, and other industrial applications. During its life span, a turbine blade is taken out periodically for repair and maintenance. This includes re-coating the blade surface and re-drilling the cooling holes/channels. A successful laser re-drilling requires the measurement of a hole within the accuracy of ${\pm}0.15mm$ in position and ${\pm}3^{\circ}$ in orientation. Detection of gas turbine blade/vane cooling hole position and orientation thus becomes a very important step for the vane/blade repair process. The industry is in urgent need of an automated system to fulfill the above task. This paper proposes approaches and algorithms to detect the cooling hole position and orientation by using a vision system mounted on a robot arm. The channel orientation is determined based on the alignment of the vision system with the channel axis. The opening position of the channel is the intersection between the channel axis and the surface around the channel opening. Experimental results have indicated that the concept of cooling hole identification is feasible. It has been shown that the reproducible detection of cooling channel position is with +/- 0.15mm accuracy and cooling channel orientation is with +/$-\;3^{\circ}$ with the current test conditions. Average processing time to search and identify channel position and orientation is less than 1 minute.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.4
• /
• pp.381-390
• /
• 1999

In this study, a pseudo ship structure data model for the :.hip cargo hold structure based on STEP is proposed. The proposed data model is based on Application Reference Model of AP218 Ship Structure which is the model that specifies conceptual structures and constraints used to describe the information requirements of an application. And the proposeddata model refers the Ship Common Model framework for the model architecture which is the basis for ongoing ship AP development within the ISO ship-building group and the ship product definition information model of CSDP research project for analyzing the relationship between ship structure model entities. The proposed data model includes Space, Compartment. Ship Structural System, Structural Part and Structural Feature of cargo hold. To generate this data model schema in EXPRESS format, ‘GX-Converter’was used which enables user to edit a model in EXPRESS format and convert schema file in EXPRESS format. Using this model schema, STEP physical file containing design data for ship cargo hold data structure was generated through SDAI programming. The another STEP physical file was also generated containing geometry data of ship cargo hold which was extracted and calculated by SDAI and external surface/surface intersection program. The geometry information of ship cargo hold can be then transferred to commercial CAD system, for example, Pro/Engineer. Examples of the modification of the design information are also Presented.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.4
• /
• pp.244-250
• /
• 2017

Effects of plating conditions (dispersant concentration, plating time, and ultrasonication) on electroless Cu plating on SiC fabric woven by crossing of SiC continuous fibers vertically were studied. The ultrasonic dispersion treatment not only did not improve the dispersion of the SiC fibers, but also did not change the plating thickness. The ultrasonication in the pretreatment step of electroless plating did not improve the dispersion of the fibers, while the ultrasonication in the plating step enhanced the dispersion of the fibers and decreased the thickness of the Cu films. It was possible to control the thickness of the Cu coating layer as well as the dispersion of the fibers in the fabric by changing the plating conditions such as dispersant concentration, plating time, and ultrasonication, but it was very difficult to coat copper on the intersection of vertical fibers in the fabric.