• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.89-93
• /
• 1997

A superlastic material, aluminum - lithium alloy 8090, were examined with uniaxial tensile test to investigate its thermomechanical behavior. The tests were carried out at the strain-rates ranging from 2${\times}$10-4 to 1${\times}$10-2 and at the temperatures from 48 0$^{\circ}C$ to 540$^{\circ}C$. The experiments produced force-displacement curves which converted to stress-strain curves. From the curves, several important superplastic factor such as strain-rate sensitivity, optimum strain-rate and strength coefficient were obtained.

• 소성∙가공
• /
• 제21권3호
• /
• pp.151-159
• /
• 2012

Finite element simulations were conducted to investigate the influence of grain growth in the superplastic blow forming process. A microstructure-based constitutive model considering grain growth effects is proposed and used in the simulations. Also, a grain growth rate equation accounting for both static and dynamic grain growth is implemented. The simulations were made using a 2D plane-strain model for constrained blow forming and an axisymmetric model for free bulging. These two models showed different features during the forming stages. However, the forming pressure-time curve and the thickness distribution obtained by both simulations explained well the deformation hardening induced by the grain growth during superplastic forming. This study shows that grain growth is an important factor in determining the material behavior during superplastic deformation.

• 소성∙가공
• /
• 제28권1호
• /
• pp.15-20
• /
• 2019

The superplastic forming/diffusion bonding process has been developed to fabricate a core frame structure with joint nodes out of tubes, for the development of a titanium high performance bicycle. The hydroforming process has been applied for bulging of a tube in the superplastic condition before, and during the diffusion bonding process. In this experiment, a commercial Ti-3Al-2.5V tube was selected as raw material for the study. The forming experiment has been performed using a servo-hydraulic press with a capacity of 200 ton. Next, nitrogen gas was used to acquire necessary pressure for the bulging and bonding of the tubes to fabricate the joint nodes. The pertinent processing temperature was $870^{\circ}C$ for the superplastic hydroforming/diffusion bonding (SHF/DB) process, using the Ti-3Al-2.5V tube. The bonding quality and the progress of bulging and diffusion bonding have been observed by the investigation of the joining interfaces at the cross section of the joint structure. The control of the nitrogen pressure throughout the SHF/DB process, was an important factor to avoid any significant defects in the joint structure. The whole progress stage of the diffusion bonding could be observed at a joint interface. A core structure with 5 joint nodes to manufacture a titanium bicycle could be obtained in a SHF/DB process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.329-334
• /
• 1992

It has been shown that the application of hydrostatic pressure during superplastic forming of 8090A1 can prevent the cavitaiton normally encountered at atmospheric pressure and cavity growth rate factor .eta. in the plane strain state is greater than that in the equibiaxial stress state. .eta. value shows some difference compared to the theoretical value, which seems to be due to the continuous nucletion and coalescence of voids during superplastic deformation. Scatter of measured data of cavity volume fraction seems to be on preferential nucleation of viods on non-uniformly distributed second phase particles in the deforming matrix.

• 한국세라믹학회지
• /
• 제47권3호
• /
• pp.205-209
• /
• 2010

In the last (fourth) section, the discussion will entail a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of $1400^{\circ}C$. This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method.

• 한국세라믹학회지
• /
• 제46권4호
• /
• pp.345-349
• /
• 2009

In Part II, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method, SPS. These improvements in mechanical properties were briefly discussed in the context of the results from the microstructural investigations. SPS forming approach provides a new route for low temperature and high-strain-rate superplasticity for nanostructured materials and should impact and interest a broad range of scientists in materials research and superplastic forming technology.

• 기술혁신학회지
• /
• 제8권3호
• /
• pp.1027-1059
• /
• 2005

The purpose of this paper is to analyze the dynamic characteristics of innovation sources such as scientific knowledges, processing technologies and user's needs in advanced metals technology. The journal articles data of four advanced materials are analyzed; amorphous metals, superplastic materials, shape memory alloys and aluminum-lithium alloy. Some regularities are found from the analysis of the four materials. The innovation proceeds through close interactions among the innovation sources. As the innovation proceeds, the relative importance of each source changes: scientific knowledge initiates the innovation and becomes the most important source in the first phase, then the processing technologies increase importance in the second phase, and then scientific knowledge, again, becomes the leading factor of innovation. Scientific knowledge and processing technology take turns leading the innovation. The impacts of users' needs to the innovation increase more and more as innovation proceeds. The results of analysis imply to the policy makers that emphasis of policy, and therefore the allocation of sources for innovation, should vary along the phases in the life cycle of advanced metals technology.

• 열처리공학회지
• /
• 제17권1호
• /
• pp.23-28
• /
• 2004

In this work, the effect of Sc and Mm(misch metal) on the high temperature behavior of Al-Mg alloys was observed. Hardness was increased due to appearance of fine $Al_3Sc$ precipitates. The elongation of Al-Mg-Sc alloy at high temperature was higher than that of Al-Mg-Sc-Mm alloy because Al-Mg-Sc alloy has finer grain sizes than Al-Mg-Sc-Mm alloy. The strain rate sensitivity factor, "m" of Al-Mg-Sc and Al-Mg-Sc-Mm at $475^{\circ}C$ and $1{\times}10^{-2}s^{-1}$ were 0.33 and 0.46, respectively. The activation energy of Al-Mg-Sc and Al-Mg-Sc-Mm alloy for superplastic deformation was 133KJ/mol and 103KJ/mol respectively. The elongation of Al-Mg-Sc alloy at high temperature was decreased by the addition of Mm, but the strength at high temperatures and low strain rate was improved.