• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.70-77
• /
• 1999

A miniaturized voltage controlled oscillator using multi-layer ceramic technology at PCS frequency band is designed and fabricated. To improve the phase noise characteristics and to reduce the size, the strip line which is embedded in a high performance multi-layer ceramic substrate is used as an inductor of VCO. And the fabricated VCO is very small size ($6mm\times6mm\times2mm$). At the bias condition of 3.3 V and 9mA, the output power and phase noise in the operating frequency range of 1,720~1,780 MHz are -3.7 dBm and -95 dBc/Hz at 10 KHz offset from the carrier, respectively. The phase noise and size are better than the conventional VCO using glass epoxy substrate.

• Journal of IKEEE
• /
• v.10 no.2 s.19
• /
• pp.109-115
• /
• 2006

In this paper, High order derivative Gaussian pulse generator for DS-UWB communication satisfying the regulation of FCC was proposed and fabricated. In order to transform rectangular signal of 100Mbps to a Gaussian pulse, the fabricated Gaussian pulse generator consists of only two SRD. The output pulse had the widths of 330 psec and amplitudes of 920 mV. In addition, the designed and fabricated dual bandpass filter shows high order derivate characteristics by using micro-strip line and parallel stub to remove WLAN band. We generated the 13th Gaussian pulse restricted frequency spectrum of WLAN band more than -25dB. The pulse had pulse width of 1 nsec and amplitude of 25 mV.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.4 s.346
• /
• pp.31-37
• /
• 2006

Strongly motivated by the need for significant reduction in the optics-to-antenna interface circuitry used in a Photonically controlled array, it has proposed the design development of a novel 'true photonic antenna' consisted of optical fiber and micro-strip antenna. To clarify the design capability of the geometry, modal transmission-line theory including the discontinuity property between circular i,nd planar guiding structures is defined, md the optical power coupling of a slot-coupled microstrip antenna directly fed from an optical fiber using photoconductive effect is evaluated numerically. The numerical results reveal that the maximum power transfer between the two different guiding structures occurs at a new point in which the guiding powers of two rigorous modes are equally partitioned.

• ETRI Journal
• /
• v.36 no.1
• /
• pp.116-123
• /
• 2014

In this paper, a novel unequal broadband out-of-phase power divider (PD) is presented. Double-sided parallel-strip lines (DSPSLs) are employed to achieve an out-of-phase response. Also, an asymmetric dual-band matching structure with two external isolation resistors is utilized to obtain arbitrary unequal power division, in which the resistors are directly grounded for heat sinking. A through ground via (TGV), connecting the top and bottom sides of the DSPSLs, is used to short the isolation components. Additionally, this property can efficiently improve the broadband matching and isolation bandwidths. To investigate the proposed divider in detail, a set of design equations are derived based on the circuit theory and transmission line theory. The theoretical analysis shows that broadband responses can be obtained as proper frequency ratios are adopted. To verify the proposed concept, a sample divider with a power division of 2:1 is demonstrated. The measured results exhibit a broad bandwidth from 1.19 GHz to 2.19 GHz (59.2%) with a return loss better than 10 dB and port isolation of 18 dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.125-130
• /
• 2004

The characteristics of on-chip spiral rectangular inductors in CMOS process are investigated through the simulation and experiment. The ADS-momentum is used for EM simulation, and the spiral inductors are fabricated with Hynix 0.35㎛ CMOS process. This research mainly concerned the effects of the geometric change in terms of the number of turns and the width of micro strip line. The measured and simulated results show that the Hynix 0.35㎛ process could support a top metal spiral inductor of 1nH to 6nH with Q-factor less than 5.

• Journal of Korea Foundry Society
• /
• v.10 no.5
• /
• pp.435-443
• /
• 1990

By using the centrifugal atomization, which is one of the rapid solidification processes, Al-5,10wt%Pb alloys which are monotectic alloys were melted at 150K over two liquid phase line in the phase diagram. The melted alloy was poured on the rotating disk, being made into atomized powders, and then the solidified microstructure and morphology of the powder were investigated. This study converted the produced powders into strips by strained powder rolling. According to sintering temperature, the microstructure and hardness were investigated. The solidified structure of the powders were almost cellular dendritic structure. Pb particles ($2.0-3.0{\mu}m$) were fairl distributed in the Al matrix. Powder shapes were irregular. Rolling property and the compacting was good, respectively, because of increasing mechanical interlocking and surface area in the small size powders. With increasing temperature, the boundarys of powders were in porous form due to the diffusion. Pb particles which were surrounding the pores were inverse-segregated at the surface of the powders. With increasing of sintering temperature, the hardness of the powders and the strips decreased. In particular rolling-strip, the hardness abruptly decreased due to the release of work-hardening.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4B
• /
• pp.637-646
• /
• 2010

For 40 Gb/s data transmission through electrical backplane trace up to 40 inch length on four layer fire-resistant (FR-4), we have designed the 40 Gb/s backplane channel model consisting of four channel 10 Gb/s. Simulation results show an enhancement of backplane channel characteristics excellent more than requirements specified in IEEE P802.3ba at 10 Gb/s. This paper provides a review of the structures and algorithms used in receive and adaptive equalization for 40 Gb/s backplane Ethernet. The use of this backplane channel model could achieves better receive equalizer at great data rate than 10 Gb/s.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1286-1291
• /
• 2003

Quench behavior of resistive superconducting fault current limiters (SFCLS) with various pattern shapes was investigated. The pattern shapes employed were meander, bi-spiral, and spital shapes of identical line width, gap and margin. SFCLS were fabricated from YBCO thin films grown on two-inch diameter Al$_2$O$_3$ substrates under the same conditions. The total length of current limiting paths was the shortest at the spital shape due to its larger useless space. Inductance component of SFCLs with the spiral shape was around two times as high as those of other two shapes. This is not desirable since impedance characteristics of existing power systems can be changed. Resistance rise of current limiting elements was low at a spiral shape before the whole quench completion, which may act as a disadvantage for simultaneous quench in serial connection between current limiting elements, but the temperature tended to have similar values at higher voltages. On the other hand, hi-spital shape was severe at insulation level between current limiting lines. When these aspects were considered, we concluded that a meander shape was appropriate to design for a resistive SFCL based on thin films except the concentration of electric field at edge areas of strip lines.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.441-448
• /
• 2012

This paper proposes a multiband Multi-Input Multi-output(MIMO) antenna for universal serial bus(USB) dongle application. The proposed MIMO antenna consists of a modified meander strip line and inverted L stub. The two radiating elements of the MIMO antenna are symmetrically placed with respect to the center of the ground plane. The fabricated antenna satisfied a VSWR below 3 and an efficiency over 35 % in the LTE band 13, 17(704 MHz-787 MHz), DCS/PCS/WCDMA band(1.71 GHz-2.17 GHz), and LTE band 7(2.5 GHz-2.7 GHz). The envelope correlation coefficient(ECC) has below 0.45 in the LTE band 13, 17 and 0.1 in the DCS/PCS/WCDMA band and LTE band 7, respectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.22-34
• /
• 1996

Regarding the plate bending process by line heating method, in this study a simplified numerical analysis is performed for a beam model to predict its residual deformation and stress distribution. Using the modified strip theory and beam finite element method, a PC-based simulation program is developed for a thermo-elastic-plastic beam. The plate bending problem can be approximately replaced by a beam model using distributed springs to account for the effect of adjacent strips. The spring constants are chosen as the best fit with experiments. In this paper, it is assumed that the temperature distribution is already given and the temperature-dependent material properties are considered. To verify the simulation program, the results using present numerical algorithm are compared with other published experimental results and similar numerical studies. The comparison shows good agreement. The present PC-based computer program also shows good efficiency in computing time.