• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.340-348
• /
• 2002

Deformation analysis of injection molded articles whose geometry is considered as the assembly of thin flat plates has been conducted. For the in-mold analysis, thermo-viscoelastic stress calculation of thermo-rheologically simple amorphous polymer and in-mold deformation calculation considering the in-plane mold constraint have been done. Free volume theory has been used to represent the non-equilibrium density state during the fast cooling. At ejection, instantaneous deformation takes place due to the redistribution of in-mold residual stress. During out-of-mold cooling after ejection, thermoelastic model based on the effective temperature has been adopted for the calculation of out-of-mold deformation. In this study, emphasis is also made on the treatment with regard to lateral constraint types during molding process. Two typical mold geometries are used to test the numerical simulation modeling developed in this study.

• Geomechanics and Engineering
• /
• 제10권3호
• /
• pp.325-334
• /
• 2016

Rock salt is a near-perfect material for gas storage repositories due to its excellent ductility and low permeability. Gas storage in rock salt layers during gas injection and gas production causes the stress redistribution surrounding the cavity. The triaxial cyclic loading and unloading tests for rock salt were performed in this paper. The elastic-plastic deformation behaviour of rock salt under cyclic loading was observed. Rock salt experienced strain hardening during the initial loading, and the irreversible deformation was large under low stress station, meanwhile the residual stress became larger along with the increase of deviatoric stress. Confining pressure had a significant effect on the unloading modulus for the variation of mechanical parameters. Based on the theory of elastic-plastic damage mechanics, the evolution of damage during cyclic loading and unloading under various confining pressure was described.

• 한국산업융합학회 논문집
• /
• 제13권3호
• /
• pp.125-131
• /
• 2010

This study is to give more accurate information by performing the time depend ent analysis to take into account the long-term losses of precast PSC concrete bridge and analyzing the second stress, final camber and cross section stress of precast PSC caused by creep and drying shrinkage. As time goes by, the stress and deformation in the cross section vary continuously by the influence of creep and drying shrinkage. Due to this, the stress redistribution occurs and the internal force variation also happens along the point on the same cross section and with the passage of time.

• Geomechanics and Engineering
• /
• 제19권1호
• /
• pp.79-91
• /
• 2019

Renewed interest in the long-term pile foundations has been driven by the increase in offshore wind turbine installation to generate renewable energy. A monopile subjected to repetitive loads experiences an evolution of displacements, pile rotation, and stress redistribution along the embedded portion of the pile. However, it is not fully understood how the embedded pile interacts with the surrounding soil elements based on different pile geometries. This study investigates the long-term soil response around offshore monopiles using finite element method. The semi-empirical numerical approach is adopted to account for the fundamental features of volumetric strain (terminal void ratio) and shear strain (shakedown and ratcheting), the strain accumulation rate, and stress obliquity. The model is tested with different strain boundary conditions and stress obliquity by relaxing four model parameters. The parametric study includes pile diameter, embedded length, and moment arm distance from the surface. Numerical results indicate that different pile geometries produce a distinct evolution of lateral displacement and stress. In particular, the repetitive lateral load increases the global lateral load resistance. Further analysis provides insight into the propagation of the shear localization from the pile tip to the ground surface.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.449-456
• /
• 1999

The concrete wall is the most useful of retaining structure which can obtain the engineering stability, but has problems that is not friendly with nature environment in a fine view, such as poor rear drainage, and shrinkage crack by temperature difference, etc. Because of this problems, the research for a segmental crib retaining wall has been performed. A segmental crib retaining wall is quickly and easily erected because is possible to be erected as the individual members, and is not sensitive to differential settlement and earthquakes. Also, it shows effective drainage and has a friendly advantage with nature environment because of being able to be planted with vines and shrubs in retaining walls The design of crib retaining walls has traditionally been based on classical soil mechanics theories. These theories, originally derived by Rankine(1857) and Coulomb(1776), assume that the wall acts as a rigid body. This assumption results in failure being predicted by either monolithic overturning or base sliding mechanisms. However, the wall consists of individual members which have been created a three dimensional grid. This grid confines an fill mass which becomes part of the wall. The filled wall resists the earth pressure with the same mechanism of classical gravity walls. Because of the flexibility of the individual segment, it allows relative movement between the individual members within the wall. The three dimensional flexible grid leads to stress redistribution when the wall is subjected to external or fill loads. Due to the flexibility and the stress redistribution, the failure of segmental crib wall consists of not only overturing and base sliding but the local deformation and the failure between the segmental members. It has been researched in the field that due to this flexibility and load redistribution, serviceability failure of segmental crib walls is unlikely to be due to overturning or base sliding. Therefore, in this study, the relative displacement appearance of retaining wall due to variation of inclination is measured to examine this behavior characteristics. Also, the behavior characteristics of retaining walls by surcharge load, and location of acting point of retaining wall rear, and the displacement characteristics and deflections are estimated about the existence and nonexistence of Rear Stretcher performing an role in transmitting earth pressure of Header and Stretcher organizing retaining walls. This research focuses on the characteristics due to the behavior of retaining walls. This research focuses on the characteristics due to the behavior of retaining walls.

• 대한핵의학회지
• /
• 제27권2호
• /
• pp.155-160
• /
• 1993

심근생존능은 심기능이 저하되어 있으나 적절한 치료에 의해 심기능이 회복될 수 있는 상태를 말하며, 기절심근과 동면심근으로 대변할 수 있다. 기절심근은 심근관류가 정상이지만 아직 심근기능이 회복이 안된 상태로 수 시간 내지 수주일 후에 회복이 되는 상태를 말하며, 동면심근은 심근관류가 오랫동안 감소되어 있어 심기능 저하되어 있지만 심근관류를 정상화시켜주면 바른 시간내에 심기능이 회복되는 상태를 말한다. 임상적으로는 이 두가지 상태가 혼합된 경우도 있으리라 추측되고 있다. 심근생존능을 진단하는 것은 재혈관화 치료를 시행하기 전에 미리 환자의 예후를 결정해 줄 수 있다는 점에서 임상적인 의의가 있다. 그 진단법으로는 PET에 의해 심근대사기능이 존재함을 증명하는 것이 표준으로 되어 있으나, 그 외에도 심장초음파, 심장 MRI등을 이용한 검사법, $^{201}TI$ 또는 $^{99m}Tc-MIBI$를 이용한 신티그라피등의 검사법이 있다. 현재까지 보고된 바를 종합하면 $^{201}TI$ 부하-재분포-재주사영상법이 가장 우수한 것으로 사료되나, 각 진단법이 개선 또는 개발되고 있으므로 이에 대한 계속적인 관심이 필요하며, 핵의학적인 진단방법도 계속적으로 발전시킬 필요가 있다고 사료된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권3호
• /
• pp.17-24
• /
• 2019

탄소섬유보강폴리머(CFRP)는 경량이며, 성형성 및 작업성이 뛰어나 보수보강재료로서 널리 사용되고 있다. 하지만, 연성재료인 철근과는 달리 CFRP는 취성재료이므로, 철근에서 사용되는 전통적인 설계접근 방법을 적용하는 것은 부적합하다. 연성재료인 철근은 항복이후 요소사이의 응력재분배가 이뤄져 복합요소의 거동은 평균화된다. 따라서 복합요소의 응력 평균은 단위요소의 평균과 같고, 표준편차는 더 작아진다. 따라서 연성재료의 설계값은 증가시킬 수 있으나, 안전측, 실무적 접근에서 고정값을 사용한다. 반면 취성재료의 경우, 응력재분배를 기대하기 어려워 복합요소의 거동은 더 약한 요소에 의해 결정된다. 이에 복합요소의 응력의 평균값과 표준편차는 감소한다. 따라서 취성재료의 설계값은 요소수가 증가할수록 감소한다. 이 논문에서는 취성재료에서 정규분포를 가지는 단위요소가 요소 결합에 따라 와이블 분포를 가지게 됨을 증명하고, 이를 반영하여 하중이 작용하는 면적에 따른 물성치의 보정식을 제안하였다.

• 대한기계학회논문집A
• /
• 제20권3호
• /
• pp.832-842
• /
• 1996

Fatigue life prediction and fatigue behavior of circular notched carbon fiber reinforced plastic laminates are presented. Point and average stress criteria by Whitney and Nuismer are generalized to fatigue fracture criteria for notched laminates. Residual strength degradation model and the assumptions on the stress redistribution are introduced during the derivation of prediction equations. S-N curve, Basquin's relation, and H and H's FLPE1 are chosen for evaluation of residual strength of unnotched laminates and six prediction equations are derived. Experiments are performed using Graphite/Epoxy laminates whose fiber orientation is $[0$^\circ$/+45$^\circ$/-45$^\circ$/90$^\circ$]s. Presented prediction equations are reasonably close to experimental data and proposed appoach is found to be suitable to predict fatigue life of notched composite laminates.

• Asian-Australasian Journal of Animal Sciences
• /
• 제15권7호
• /
• pp.1022-1025
• /
• 2002

Effect of chemical stress of daily administration of glucocorticoid (dexamethasone @0.125 mg./calf/day) injections on plasma zinc levels, Zn status of body tissues and its distribution in sub cellular fractions, was studied in neonatal buffalo calves. Daily i/m injections of dexamethasone, starting at the completion of 1 week of age and continued till 8th week, led to a significant decline in plasma Zn concentration from 3rd week onwards, which then persisted throughout the rest of the experimental period. In control group, liver had the highest concentration of zinc, followed by heart, muscle, spleen, kidney and testis. In all these tissues, cytosolic fractions had the highest (>60%) zinc levels followed by nuclear, mitochondrial and microsomal fractions. In dexamethasone treated calves, there was a significant increase in the Zn uptake by the tissues of liver and muscle. This increase in zinc concentration was observed in all the sub cellular fractions of liver and muscle, however about 80% of this increase was in cytosolic fraction. It was concluded that glucocorticoid-induced stress caused increase in Zn levels of liver/muscles and decrease in blood plasma zinc, thus indicating a redistribution of Zn in body.

• 한국표면공학회지
• /
• 제30권3호
• /
• pp.191-201
• /
• 1997

Non-passivated electrolytic tinplates withour conventinal chemical treatment self-oxidize in ambient atmosphere to from yellow stain on the outermost surface during the long-term storage. The degree of yellowness of the stain increased linerly with the oxide thickness due to the interfeefence color of the $SnO_2$ Even though the thickness of the oxide layer was very thin, less than 100$\AA$ , it exerts an undesirable influence on the can-making processes, particularly the stripping behavior after ironing. Investigations were carried out on the morphologies of the coating layer, the changes in oxide thickness during successive can-making processes and the averge friction coefficients with the different oxide thinkness. These oxide layers were broken up and distributed within the bulk tin coating during the ironing process. This redistribution of the oxide layer prvented smooth pressing-aside of the tin coating layer, resulting in an increase in the ironing friction coefficient. As the friction was increased, the residual stress along the can wall thinkness(i.e., the hoop stress) was also increased. Due to both the oxibe layer accumulation, which increased the friction coefficient, and the hoop stress, can stripping efficiency without roll-back is reduced.