• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.78-87
• /
• 1999

A mathematical model for the stress free surface profile in Over-Round and Round-Oval grove rolling, which can be used effectively in the calculation of pass area, is presented. The new model has generality, simplicity and accuracy for practical usage. The stress free surface profile of an outgoing stock can be modeled when the maximum spread of it known a priori. The equation for the stress free surface profile is formulated from the linear interpolation of the radius of curvature of an incoming stock and that of roll groove to the axis direction. In developing the analytical model, the effect of rolling temperature and friction between roll and work piece(stock) were not considered since the geometry of roll groove and the incoming work piece were assumed a dominant factor which decides the stress free surface profile of the outgoing stock. A simulation with the analytical model developed also has been carried out to demonstrate the stress free surface profile of the outgoing stock.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.198-204
• /
• 1987

본 논문에서는 전보에서 창성된 인벌류우트-원호합성치형기어에 있어서 Hertz 식에 의하여 치면접촉응력을 구하고 유한요소법에 의하여 이뿌리응력을 계산하였다. 그리고 같은 제원의 표준 인벌류우트 치형기어와 비교하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2533-2535
• /
• 1998

In this paper, an effect of drive-in process temperature on the residual stress profile of the p+ silicon film has been investigated. The residual stress profile has been calculated as the fourth-order polynomials. All coefficients of the polynomials have been determined from the measurement of the vertical deflections of the p+ silicon cantilevers with various thickness and the tip displacement of the p+ silicon rotating beam. From the determination results of the residual stress profile, the average stress of the film thermally oxidized at 1000 $^{\circ}C$ is 15 MPa and that of the film oxidized at 1100 $^{\circ}C$ is 25 MPa. The profile of the residual stress through the high temperature drive-in process has a steeper gradient than the other case.

• Tribology and Lubricants
• /
• 제19권6호
• /
• pp.357-364
• /
• 2003

The sub­surface stress field beneath the gear's contact surface caused by the contact pressure in lubricated condition has been calculated. To evaluate the influence of the clearance shape on the stress field, two kinds of tooth profile models were chosen. One is the conventional cylinder contact model and the other is the new numerical model. Love's rectangular patch solution was used to obtain the sub­surface stress field. The analysis results show that the sub­surface stress is quite dependent on both the contact pressure and the profile model. The maximum effective stress of the new model is lower than that of the old model. The depth where the maximum effective stress occurs in the new model is not proportional to the intensity of the external load.

• 한국기계가공학회지
• /
• 제9권5호
• /
• pp.40-49
• /
• 2010

Conical involute gears are being used for marine gearboxes, automotive transmissions, and robots, and so on, but not much. As involute profile gear, conical involute gear not only can be engaged with spur and helical gear but also can be used for power transmission of parallel, crossed and skewed axis with small angle. Hence, conical involute gears are likely to develop in future. Through a study on the basic theory of conical involute gear, tooth surface compressive stress analysis was performed by using commercial modeling program, comparing before and after profile modification. As a result, it noticed that tooth profile modification is able to relieve more tooth surface compressive stress than before modification.

• 한국정밀공학회지
• /
• 제32권12호
• /
• pp.1011-1016
• /
• 2015

In a roll-to-roll continuous system, winding is one of the most important processes since it determines the quality of the final manufactured products such as flexible film and printed electronic devices. Since an adequate winding tension can reduce the incidence of the defects that are derived from the inner stress of the wound roll such as starring and telescoping, it is necessary to determine the optimal taper-tension profile. In this study, an algorithm for the setting of an optimal taper-tension profile in consideration of the residual stress in the wound roll is suggested; furthermore, the algorithm was adjusted for the determination of an optimal taper-tension profile regarding the winding process of $10{\mu}m$ polypropylene (PP) film. As a result of the algorithm-generated, optimal taper-tension profile, the residual stress and radial stress in a PP wound roll were decreased to 27.37 % and 40.05 % (mean value), respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.174-180
• /
• 2002

The subsurface stress field beneath the roller's contacting surface due to the contact pressure in lubricating condition has been calculated. Main purpose of this study in view of engineering is to prove the validity of the numerical profile roller presented by Koo et al. The Love's rectangular patch solution was used to obtain the subsurface stress field. The stress field of the numerical profile roller was compared with the one of the existing dub-off profile roller The analysis results show reduced subsurface stresses for the numerical profile roller.

• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1498-1506
• /
• 1997

Procedures are presented for influence of shot peening on fatigue strength, fatigue life and effects of shot peening are discussed from experiments were taken between shot peened and unpeened SPS5, SM45C specimens. After the residual stress on shot peened specimens was measured by X-ray diffractometer, rotating bending fatigue tests were carried out. In addition, the compressive residual stress profile was obtained by the superposition method of three stresses which is based on Al-Obaid's equation. Predicted fatigue life considering residual stress profile which was obtained by the Al-Obaid's equation and another predicted fatigue life considering residual stress profile which was measured in test were compared. For the purpose of predicting fatigue life, Morrow's equation considering the residual stress and mean stress was used.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권9호
• /
• pp.665-671
• /
• 1999

The paper represents the effects of the drive-in process parameters on the residual stress profile of the $p^+$ silicon film. Since the residual stress profile is notuniform along the direction normal to the surface, the residual stress is assumed to be a polynomial function of the depth. All the coefficients of the polynomial can be determined by measuring of the thicknesses and the deflections of cantilevers and the deflection of a rotating beam with a surface profiler meter and a microscope. As the drive-in temperature or the drive-in time increases, the boron concentration decreases and the magnitude of the average residual tensile stress decreases. Then, near the surface of the $p^+$ film the residual tensile stress is transformed into the residual compressive stress and its magnitude increases.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.191-192
• /
• 2006

The deformation under radial pressure of rectangular dies for metal powder compaction has been investigated by FEM. The explored variables have been: aspect ratio of die profile, ratio between diagonal of the profile and die height, insert and ring thickness, radius at die corners, interference, different insert materials, i. e. conventional HSS, HSS from powders, cemented carbide (10% Co). The analyses have ascertained the unwanted appearance of tensile normal stress on brittle materials, also "at rest", and even some dramatic changes of stress patterns as the die height increases with respect to the rectangular profile dimensions. Different materials behave differently, mainly due to difference of thermal expansion coefficients. Profile changes occur when the dies are heated up to the temperature required for warm compaction. The deformation patterns depend on compaction temperature and thermal expansion coefficients.