• Tunnel and Underground Space
• /
• v.4 no.3
• /
• pp.261-273
• /
• 1994

Direct shear tests were carried out on the rock joints and artificial discontinuities to investigate the influence of joint roughness on the shear strength and deformation behaviour. Single direct shear testing apparatus used in experiment was designed and manufactured. Its capacity is 200 tons of shear load, 20 tons of normal load and 50$\textrm{cm}^2$ of maximum shear area. Test samples were cement mortar with artificial discontinuity and sandstone with natural joint. Peak shear strength was increased as joint roughness or normal stress was increased, especially, linearly increased with roughness angle in cement mortar. If joint roughness angle was constant at low normal stress, shear strength was not affected by width and height of joint roughness in cement mortar. Peak shear strengths obtained from tests were larger than the values calculated by Barton's equation, and shear stiffness was increased with joint roughness coefficient.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.1
• /
• pp.1-9
• /
• 2000

This study was carried out to improve the opacity of printing paper. Conventional filler loading enhanced the opacity of paper, but subsequently caused reduction of paper strength of paper. We try to seek a new filler loading method so-called beater loading that enhances opacity of paper as well as sustained desire strength. In our experiment, comparing to direct loading method, the beater loading method enhanced 0.8% of opacity and 0.2% of brightness. This also decreased the rates of strength reduction of paper. Therefore, the results obtained in this study indicated that beater loading was a very effective method to improve the opacity of paper while not to decreased so much of paper strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.109-113
• /
• 2003

In this experiment, we distribute the bending angle to 60$^{\circ}$, 90$^{\circ}$, 120$^{\circ}$, and we separate it in to two groups. One is straightening right after bending and the other is straightening after one week. The bars we will use are HD13 and HD16. The number of tests will be 60 times. In the case of HD16, the increase of bending angle decreased yield strength and maximum strength. And compared with thinner bars, HD16 showed bigger differences in yield strength and maximum strength when the 'being bent' duration got longer. So it shows that when we bend and after straighten a bar, stress change takes place on the surface of the bar. At the beginning it shows it's ductility after that it deforms while transforming it's character to destroying. And also, if we straighten a bar after bending, it doesn't get straighten like the original form. So it makes torsion and this torsion makes moments in different areas.

• Journal of Welding and Joining
• /
• v.20 no.5
• /
• pp.72-77
• /
• 2002

Flip-chip interconnection that uses solder bump is an essential technology to improve the performance of microelectronics which require higher working speed, higher density, and smaller size. In this paper, the shear strength of Cr/Cr-Cu/Cu UBM structure of the high-melting solder b01p and that of low-melting solder bump after aging is evaluated. Observe intermetallic compound and bump joint condition at the interface between solder and UBM by SEM and TEM. And analyze the shear load concentrated to bump applying finite element analysis. As a result of experiment, the maximum shear strength of Sn-97wt%Pb which was treated 900 hrs aging has been decreased as 25% and Sn-37wt%Pb sample has been decreased as 20%. By the aging process, the growth of $Cu_6Sn_5$ and $Cu_3Sn$ is ascertained. And the tendency of crack path movement that is interior of a solder to intermetallic compound interface is found.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.1
• /
• pp.161-168
• /
• 2001

The use of composite members to improve the compressive strength of steel structure is a common practice these days and its efficiency has already been proved by several researches and experiments. The result of concrete filled circular tubular(CFCT) stub column tests is introduced in this paper. The main parameter of this test is the ratio of diameter to thickness of circular hollow section. From the test results, the effect of concrete filled in steel tube on the ultimate strength, the deformation capacity and initial stiffness are discussed. The purpose of this paper is to investigate the effect of various parameters and evaluate the compressive strength of confined concrete. It would contribute to a better understanding of CFT structure, further laboratory experimentations are needed for better accurate estimation on its effect.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.867-870
• /
• 1998

The reinforced concrete structures have been deteriorated for various causes since it serviced for the long time. If we have to service concrete structure long time, we must repair it using appropriate methods and materials. But the data which evaluate the repair material has not been sufficient. So, the aim of this research is to estimate properties of repair materials and to acquire the data which apply to the concrete structures in field. To accomplish this objective, we have made experiment on compressive strength, bond strength, the coefficient of thermal expansion and setting time. Generally, compressive strength and bond strength are favorable but some products are unfavorable under wet curing. Setting time was faster than ordinary portland cement mortar except one material.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.154-165
• /
• 1996

As II-anhydrite reacts with C3A(aluminate), C4AF(ferrite) at initial hydration of cement and assists the hydrolysis of C3S(calcium silicate), the production rate of ettringite(3C3A.3CaSO4.32H2O) and C-S-H gel was acclerated. It was known that compressive strength of cement concrete improved due to the effect of II-anhydrite. For the checking these effects of II-anhydrite, the fluidity and compressive strength of cementmortar admixed with II-anhydrite and pozollanic fine powders were investigated. By means of SEM analysis, the surface structure of mortar with the condition of steam curing at curing days=28 was investigated. As a result of this experiment, it was examined that II-anhydrite had an increase on the fluidity of cementpaste and compressive strength of mortar.

• Journal of the Korean Ceramic Society
• /
• v.43 no.9 s.292
• /
• pp.537-543
• /
• 2006

Length change, hydration heat, setting time and compressive strength of OPC were measured by adding KCl and replacing limestone powder so as to examine the influence of limestone powder on hydration of the OPC contained much chloride. In general, the chloride modified cement was high in heat of hydration, short in its setting time, low in its fluidity and low in its strength at 28 days due to the sudden hydration in its initial stage. As a result of the experiment, it has been demonstrated that heat of hydration, became low as one replaced limestone powder to the chloride modified cement, and the fluidity and shrinkage rate of mortar decreased without change in setting time; furthermore, the compressive strength at 28 days was improved.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.87-90
• /
• 2007

The purpose of this study is to investigate the properties of concrete with the kinds and addition of expansive additives. 2 kinds of expansive additives produced in our country and 0, 10, 20, 30, 40% of ratio of addition rate are selected for this experiment. According to experimental results, flow, slump and air rate of concrete with expansive additives is nearly same with its of plain concrete and compressive strength, tensile strength of concrete with expansive additives at 28 days is higher than that of plain concrete. Therefore, The expansion concrete is able to manufactured so it consumes by restricted effects.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.78-79
• /
• 2015

For estimating compressive strength of concrete, non-destructive test has conducted generally. It used experimental equation to calculate compressive strength from construction. This study investigated experiment to apply non-destructive test, based on fresh property, compressive strength and ultrasonic pulse velocity of high performance concrete. And it conducted to compare various proposed equation.