• 한국인터넷방송통신학회논문지
• /
• 제9권3호
• /
• pp.45-54
• /
• 2009

본 논문은 신경외과 및 일반외과 영역에서 골 고정용 금속판으로 골 수술 및 치료를 하는 과정에서 골 고정요 금속판의 굴곡강도와 강성을 평가할 수 있는 강요평가 알고리즘을 구현하였다. 굴곡곡선의 최대 포인트 점은 0.2% 상쇄변위(offset displacement)에서 평형하게 접근 할 수 있는 포인트 P점을 최대 하중에 부여하는 굴곡 점으로 적용하였다. 실험에 사용한 플레이트(Plate)는 ${\Phi}13$와 ${\Phi}18$이며, 강도평가의 알고리즘은 플레이트 ${\Phi}13$, ${\Phi}18$, ${\Phi}13-{\Phi}18$ 비교하였으며, 플레이트에 압박하는 힘의 알고리즘을 산출한 결과 굽힘강도의 최대값이 311N, 387N, 410N, 474N로 나타났고, 변위(Displacement)에 따라 하중에 견디는 시점인 인장강도가274(N), 324(N), 382(N), 394(N)로 나타났음으로 이 시점이 금속판의 굴곡운동 값으로 결정되었다. 본 연구의 결과로 한 개의 축을 기준으로 발생하는 골 고정용 금속판의 강도 조절 문제를 평가알고리즘으로 구성함으로 해결할 수 있었고, 형태 변화에 따른 조절기능을 검증할 수 있는 시스템이 새로운 알고리즘 형성으로 가능할 것으로 예상된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권1호
• /
• pp.129-136
• /
• 1999

In this paper, the new non-destructive equation will be proposed and evaluated in comparison to the other foreign's non-destructive equation. Through the comparisons cores strength of mock structure with compressive strength obtained from new non-destructive equation ; rebound hammer, ultra-sonic pulse velocity and combined method, it will be analyzed about application of non-destructive equation. The results are following. The new non-destructive equations follow ; (1) $F_c=9.5R{\cdot}N+62.5$ (2) $F_c=243Vp-739$ (3) $F_c=8.1R_o+205.3V_p-802$ where, $F_c$ : Compressive Strength, $R_o$ : Rebound Number. $V_p$ : Ultra-Sonic Pulse Velocity Trough the result of mock structure test, the combined method is superior to rebound method and ultra-sonic pulse velocity method in the estimation of concrete strength. In order to apply the non-destructive equation of concrete strength to the structures, it is necessary that we should be made process study on the non-destructive equation for estimation of concrete strength in the range, time and strength of application under long-term.

• 대한기계학회논문집
• /
• 제17권1호
• /
• pp.112-119
• /
• 1993

본 연구에서는 강도의 측면에서 인벌류트 원통치차의 설계 및 성능평가를 돕 기위하여 퍼스널컴퓨터 상에서 간편히 수행할 수 있는 치차의 강도평가 시스템을 개발 한다.즉, 원통치차의 굽힘강도 및 면압강도와 이들과 관련하여 기하학적인 형상, 재질, 운전상태, 신뢰성, 안전계수 등 강도에 영향을 미치는 거의 모든 인자를 일목요 연하게 평가하고 이들이 강도에 미치는 영향을 판단할 수 있는 치차의 강도평가 과정 을 하나의 시스템으로 구성함으로써 설계현장 등에서 간편히 이용할 수 있도록 하고 최종적으로 설계의 자동화를 이룰 수 있도록 한다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 가을 학술발표회 논문집
• /
• pp.542-549
• /
• 2004

The compressive strength of concrete is commonly used criterion in producing concrete. However, the tests on the compressive strength are complicated and time-consuming. More importantly, it is too late to make improvement even if the test result does not satisfy the required strength, since the test is usually performed at the 28th day after the placement of concrete at the construction site. Therefore, accurate and realistic strength estimation before the placement of concrete is being highly required. In this study, the estimation of the compressive strength of concrete was performed by probabilistic neural network (PNN) on the basis of concrete mix proportions. The estimation performance of PNN was improved by considering the correlation between input data and targeted output value. Adaptive probabilistic neural network (APNN) was proposed to automatically calculate the smoothing parameter in the conventional PNN by using the scheme of dynamic decay adjustment algorithm. The conventional PNN and APNN were applied to predict the compressive strength of concrete using actual test data of a concrete company. APNN showed better results than the conventional PNN in predicting the compressive strength of concrete.

• 한국건축시공학회지
• /
• 제6권3호
• /
• pp.59-66
• /
• 2006

This study aims to estimate strength approximate to actual concrete strength by presenting appropriate non-destructive strength estimation expression with admixtures such as fly ash, blast furnace slag and silica fume which are used as cement substitute and owing to theirs of cement owing to their equal conditions to blending characteristics of concrete used for domestic structures and their recyclable properties. As a result of comparing error rate of existing expressions and this estimation expression, error rate of this estimation is reduced compared to existing expressions and has higher reliability. When conventional concrete expression is applied to admixture concrete, error rate occurs and then this study suggests the following estimation expressions depending on types of admixture concrete.

• 한국군사과학기술학회지
• /
• 제11권4호
• /
• pp.149-158
• /
• 2008

This article provides strength estimation of T-joint area which made of composite material. Inner and outer structures of medium range surveillance radar are all made of sandwich structure which is made with composite material(CFRP) and aluminum honeycomb core. Since the radar is voluminous and has very complex inner structure, the whole structure cannot be made as one piece. Therefore, usage of T-joints is inevitable. Since some of stress concentration areas were located around T-joint area, series of strength estimations were conducted. Three different configurations were tested to improve mechanical properties(primarily on strength). The results show an improvement on strength to meet calculated strength on stress concentrated T-joint area.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.75-78
• /
• 2005

This raper investigates the effect of curing temperature on strength development of concrete incorporating cement kiln dust(CKD) and blast furnace slag (BS) quantitatively. Estimation of compressive strength of concrete was conducted using equivalent age equation and rate constant model. An increasing curing temperature results in an increase in strength at early age, but with the elapse of age, strength development at high curing temperature decreases compared with that at low curing temperature. Especially, the use of 35 has a remarkable strength development at early age and even at later age, high strength is maintained due to accelerated pozzolanic activity resulting from high temperature. Whereas, at low curing temperature, the use of BS leads to a decrease in compressive strength. Accordingly, much attention should be paid to prevent strength loss at low temperature. Based on the strength development estimation using equivalent age equation, good agreements between measured strength and calculated strength are obtained.

• Computers and Concrete
• /
• 제4권4호
• /
• pp.299-316
• /
• 2007

The compressive strength of concrete is a commonly used criterion in producing concrete. However, the test on the compressive strength is complicated and time-consuming. More importantly, since the test is usually performed 28 days after the placement of the concrete at the construction site, it is too late to make improvements if unsatisfactory test results are incurred. Therefore, an accurate and practical strength estimation method that can be used before the placement of concrete is highly desirable. In this study, the estimation of the concrete strength is performed using support vector regression (SVR) based on the mix proportion data from two ready-mixed concrete companies. The estimation performance of the SVR is then compared with that of neural network (NN). The SVR method has been found to be very efficient in estimation accuracy as well as computation time, and very practical in terms of training rather than the explicit regression analyses and the NN techniques.

• Journal of the Korean Wood Science and Technology
• /
• 제49권6호
• /
• pp.541-549
• /
• 2021

This paper reports a method to evaluate the residual strength of insect-damaged radiata pine lumber, such as the screw withdrawal strength as a semi-destructive method and a compression parallel to the grain test to assess the density changes after exposure to outdoor conditions. The screw withdrawal strength test was used as a semi-destructive method to estimate the residual density of decayed lumber. A compression parallel to the grain test was applied to evaluate the residual density. Three variables, such as the screw withdrawal strength, compression parallel to the grain, and residual density, were analyzed statistically to evaluate their relationships. The relationship between the residual density and screw withdrawal strength showed a good correlation, in which the screw withdrawal strength decreased with decreasing density. The other relationship between the residual density and compression parallel to the grain was also positively correlated; the compression parallel to the grain strength decreased with decreasing density. Finally, the correlation between the three variables was statistically significant, and the mutual correlation coefficients showed a strong correlation between the three variables. Hence, these variables are closely correlated. The test results showed that the screw withdrawal strength could be used as a semi-destructive method for an in situ estimation of an existing wood structure. Moreover, the method might approximate the residual density and compression parallel to the grain if supplemented with additional data.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.217-222
• /
• 2000

A large Pc structure building is system that consisted of bearing wall and slab joint. It has general structure stability from unity thar each members tied at joint. The strength of mortar that packing in joint among panels is important to internal force in entire building system. Do, if we could get early strength estimation with microwave. It would bring good construction planning, reduce construction time, and judge building stability and so on. The purpose of this study is to develop early estimation method for making better quality control and constructing good PC panel structure. The results of this study were as follows :1) With sealed molds, reduced moisture volatilization to more than 60% and enlarged 30% accelerated compressive strength than before one. 2) To get more accelerated strength, we should control maximum temperature difference to $30^{\circ}C$ downward 3)Interrelation with 7-day and 28-day strength were 0.831,0.902, and it is above than before one