• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.483-494
• /
• 2007

The properties of fracture system on road-cut slopes along the Busan-Ulsan express way under construction are investigated and analyzed. Fracture spacing distributions show log-normal form with extension fractures and negative exponential form with shear fractures. Straight line segments in log-log plots of cumulative fracture length indicate a power-law scaling with exponents of -1.13 in site 1, -1.01 in site 2 and -1.52 in site 3. It is likely that the stability and strength of rock mass are the lowest in site 1 as judged from the analyses of spacing, density and inter-section of fractures in three sites. In contrast, the highest efficiency of the fracture network for conducting fluid flow is seen in site 3 where the largest cluster occupies 73% through the window map. Based on the field survey data, this study modified weighting values of the RMR system using a multiple regression analysis method. The analysis result suggests a modified weighting values of the RMR parameters as follows; 18 for the intact strength of rock; 61 for RQD; 2 for spacing of discontinuities; 2 for the condition of discontinuities; and 17 for ground water.

• Journal of fish pathology
• /
• v.28 no.1
• /
• pp.37-42
• /
• 2015

In the present study, we performed a dipping of olive flounder (average length and weight: $20{\pm}2.0cm$, $70{\pm}5.0g$) for a period of three hours a day, over two days, in a melted complex of oxytetracycline (OTC) and neomycin (N), by dissolving 25-10 ppm or 50-20 ppm in water. Subsequently, the remaining antibiotic density in muscle tissue collected from olive flounder was investigated, 1, 5, 14 and 40 days after discontinuation of the medication. 5 fish were used from each group. The standard graph drawn from the results of diluting two standard solutions of OTC and N based on various density levels, showed a relatively straight line with an $R^2$ of 0.9999 and 0.9952, respectively. The recovery rate of OTC was shown to be 90-93% and N, 88-95%. Upon measurement of the remaining antibiotic density in the test group that had been exposed to 25-10 ppm of the complex of OTC and N, $0.97{\pm}0.084{\mu}g/ml$ of OTC and $0.118{\pm}0.079{\mu}g/ml$ N were detected on 1 day of the test. No antibiotic density was detected after day 5 of the test. Regarding the test group that were exposed to 50-20 ppm of the complex of OTC and N, $1.324{\pm}0.062{\mu}g/ml$ of OTC and $0.788{\pm}0.05{\mu}g/ml$ N were detected on day 1 of the test, and no antibiotic density was detected after day 5 of the test.

• Journal of Korea Water Resources Association
• /
• v.31 no.4
• /
• pp.397-406
• /
• 1998

The Pyokkolche Reservoir was constructed as a major public project of the ancient agricultural society, 1600 years ago. From a hydraulic point of view, it is considered to have been carried out with a distinguished technology. It should be in particular noticed that for a consecutive banking the main stream was diverted and drained to the Yonpo stream and the dam with same sea levels on its top along the whole length was built in a nearly straight line in spite of the different sea levels between both ends on the bottom. These suggest that the carrying out artifice and surveying technigue of those days were considerably excellent. However, the insufficient plan and design at the time of the construction, the temporary management and the repeated repair works in the later ages caused the Pyokkolche to lose its function. The Changsaenggeo and Kyungjanggeo gate sites being the facilities for sluices composed of a simple span and a vertical lift hand-operated sing a pully. The advantage of the geographical characteristics at both ends of the main dam was scientifically taken to these sites which also functioned as a spillway against a flood. The gate site of Suyogeo must have been located in an entrance to Suwolri, the northern end of the Pyokkolche and Yutonggeo is presumed to have been located on the right of Sangsori, the southern end of the Pyokklche. Keywords : Pyokkolche Reservoir, construction technology, gate site location.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.4
• /
• pp.424-430
• /
• 2002

Vas deferens is a long tube and could be divided into four regions as its morphological characters: a short and slender proximal region, a convoluted region, a straight and more thick distal region, and an ejaculatory duct, It is connected with the posterior outer horns of the testis and runs to the gonopores opened on the coxa of the fifth walking legs, The proximal region consists almost entirely of simple cuboidal epithelial cells, $12\~28{\mu}$m in height, surrounded by a thin basal membrane. A small aggregation of high cuboidal epithelium is obsened from one side of the proximal region. The convoluted and distal region is composed of two kinds of epithelial cells; high cuboidal epithelial cells, $40\~120{\mu}m$ in height located in dorsal portion and simple cuboidal epithelial cells of $12\~28{\mu}$m in height located in ventral and lateral portion. The ejaculatory duct is surrounded with two kinds of muscle layers, inner longitudinal and outer circular muscle fibers, The lumen is lined with high and simple cuboidal epithelium in almost equal proportions. The proximal region contains mature sperm and basophilic substances. The eosinophilic substances appeared newly going toward the convoluted region and are laid along simple cuboidal epithelial cell layer. Tube-like content (spermatophore) of the vas deferens is ejaculated from a pair of genital pores at mating. Two masses of the content fuse together side by side and are usually deposited on the female thorax between the second and fourth or fifth pereiopods, The spermatophore formed measures $2.7\~4.0$ mm in length and $1.5\~2.7$ mm in width.

• Restorative Dentistry and Endodontics
• /
• v.25 no.3
• /
• pp.381-389
• /
• 2000

Lateral condensation with gutta-percha and sealer has been shown to provide an excellent apical seal; however, the lateral condensation technique has demonstrated less favorable apical leakage results in curved canals when compared with straight canals. Placement of endodontic spreaders to within 1 to 2mm of the root canal working length has been advocated for optimum gutta-percha obturation. Due to their stiffness, stainless-steel(SS) spreaders will often fail to achieve this position in curved canals. Newly marketed nickel-titanium(NT) spreaders may offer an advantage in this regard due to the increased flexibility of these instruments. The purpose of this study was to evaluate the effect of NT finger spreader on the sealing ability in lateral condensation technique, compared with conventional SS finger spreader. Twenty four standardized resin models simulating curved canals(30 degree) were randomly placed into 2 groups and instrumented to a #30 master apical file size with Ni-Ti Profile .04 taper series using step down technique. Each groups was obturated with standardized gutta-percha cone by standard lateral condensation technique using SS finger spreader, NT finger spreader. And then, each model was sectioned horizontally with microtome at 1, 2, 3, 4, 5mm levels from the apex. At each of 5 levels, ratio of the area of gutta-percha was obtained by calculating the area of gutta-percha to the total area of the canal. The data collected were then analyzed statistically using a t test for independent samples. The results as follows ; 1. The total mean ratio of area of gutta-percha was 89.20${\pm}$7.00(%) for SS spreader group. 92.20${\pm}$5.17(%) for NT spreader group. There was statistically significant difference between each group(p<0.05). 2. At 3mm level, the mean ratio of area of gutta-percha was 88.32${\pm}$5.41(%) for SS spreader group, 95.25${\pm}$2.60(%) for NT spreader group. There was statistically significant difference between each group(p<0.05). At 1,2,4mm levels, NT spreader group showed greater mean ratio of area of gutta-percha than SS spreader group, too. But there was no statistically significant difference. 3. At 5mm level, the mean ratio of area of gutta-percha was 91.83${\pm}$3.42(%) for SS spreader group, 87.91${\pm}$3.68(%) for NT spreader group. There was statistically significant difference between each group(p<0.05). This study concluded that the NT spreader demonstrated somewhat favorable apical sealing effect than SS spreader in prepared curved canals. The clinical use of NT spreaders may enhance our ability to create better apical seals in curved canals, but further studies in this area will help clarify some of the remaining areas with which practitioners are concerned, such as compaction forces exerted by NT spreaders.

• Journal of Korean Society of Forest Science
• /
• v.89 no.3
• /
• pp.397-404
• /
• 2000

This study was carried out to investigate the influence of the road structure and site conditions on side-ditch stability of forest road. For experimental purposes, the forest road in the Kwangrung Experimental Forest, Korea Forestry Research Institute, was chosen as a study site. A total of 556 plots wes set up as every longitudinal gradient changing points by belt-transect method. Data of 10 road structural characteristics and side-ditch stability were collected from each plot and analysed by Quantification II. The main factors in order of partial correlation coefficient were longitudinal gradient, road position, inclination of cut-slope, constituent material of cut-slopes, distance of surface flow, cross-sectional shape of road, pavement material, vegetation of cut-slopes and length of cut-slope. The erosion of side-ditch of forest road occurred in the following cases; more than 8% of the longitudinal gradient, road position of hill under side and foot hill, more than $50^{\circ}$ of inclination of cut-slope, constituent material of cut-slopes of hard soil and gravel soil, more than 80m of distance of surface flow, pavement material with earth or gravel, more than medium covered of vegetation of cut-slopes, and the straight and convex form of road-bed.

• Korean Journal of Plant Taxonomy
• /
• v.38 no.4
• /
• pp.509-522
• /
• 2008

한국산 가막사리속(Bidens L.)에 포함된 10분류군(8종 2변종)의 수과형태를 연구하기 위하여 입체현미경과 주사전자현미경을 이용하여 관찰하였다. 연구된 가막사리속에서 까끄라기를 제외한 수과의 크기는 $3.0-19.5{\times}0.7-2.6 mm$이다. 관모는2-4개의 까끄라기로 구성되어 있고, 까끄라기의 길이는 2.2-5.6 mm이다. 강모의 배열은 1-3열이었다. 수과의 다형화가 6개의 분류군(B. bipinnata, B. biternata, B. frondosa, B. parviflora, B. pilosa var. pilosa, B. tripartita var. tripartita)에서 확인되었다. 수과의 형태와 까끄라기의 수에 의해 4가지 유형으로 구분되었다. - Type A: 장타원형이고, 까끄라기 수는 2개(B. parviflora); Type B: 장타원형이고, 까끄라기 수는 3개 이상(B. bipinnata, B. biternata, B. pilosa var. pilosa, B. pilosa var. minor) Type C: 도란형이고, 까끄라기의 수는 2개(B. frondosa, B. radiata var. radiata, B. radiata var. pinnatifida, B. tripartita var. tripartita); Type D: 도란형이고, 까끄라기의 수는 3개 이상(B. cernua). 까끄라기의 강모 표면무늬는 3가지 즉 나선상, 평활상, 불규칙한 직선형으로 나타났다. 수과의 표면은 각피층이 발달한 다각형, 평활상 그리고 굴곡형으로 나타났다. 수과형질의 분류학적 적용에 대하여 간략하게 토의하였다. 수과형질을 바탕으로 한국산 가막사리속 분류군에 대한 검색표를 제시하였다.

• Restorative Dentistry and Endodontics
• /
• v.30 no.1
• /
• pp.16-21
• /
• 2005

The purpose of present study was to compare the speed of coronal leakage before and after post space preparation using Streptococcus mutans. Forty straight extracted human teeth were selected. The crowns were removed to a uniform remaining root length 14 mm. Canals were enlarged by 06 taper $Profiles^{(R)}$ to a size $\#40$ as a master apical file. And these were filled with gutta percha point and $Tubuliseal^{(R)}$ sealer, using continuous wave technique. Groupings are as follows. Group 1 - These teeth were obturated without sealer. Group 2 - These teeth were obturated and covered the surface of the root completely with sticky wax. Group 3 - These teeth were obturated. Group 4 - These teeth were obturated and prepared for post space remaining 5 mm of gutta percha. The teeth were suspended in plastic tubes. The upper chamber received the bacterial suspension everyday to simulate clinical situation. The lower chamber consisted of BHI added Andrade's indicator. All roots in the positive control group (Group 1) turned yellow within 24 h and those of negative control group (Group 2) remained red throughout the experimental period (70 days) The samples of group 3 were contaminated within an average of 27.2 days. The samples of group 4 were contaminated within an average of 15.7 days, ranging from 9 to 22 days. There was significant difference between group 3 and group 4 statistically (p < 0.05).

• Journal of Intelligence and Information Systems
• /
• v.22 no.2
• /
• pp.115-125
• /
• 2016

The Bollinger Band indicating the current price position in the recent price action range is obtained by adding/substracting the simple standard deviation (SSD) to/from the simple moving average (SMA). In this paper, we first compare the characteristics of the SMA and the exponential moving average (EMA) in the operator's point of view. A basic equation is obtained between the interval length N of the SMA operator and the weighting factor ${\rho}$ of the EMA operator, that makes the centers of the 1st order momentums of each operator impulse respoinse identical. For equivalent N and ${\rho}$, frequency response examples are obtained and compared by using the discrete time Fourier transform. Based on observation that the SMA operator reacts more excessively than the EMA operator, we propose a novel exponential standard deviation (ESD) band centered at the EMA and derive an auto recursive formula for the proposed ESD band. Practical examples for the ESD band show that it has a smoother bound on the price action range than the Bollinger Band. Comparisons are also made for the gap corrected chart to show the advantageous feature of the ESD band even in the case of gap occurrence. Trading techniques developed for the Bollinger Band can be straight forwardly applied to those for the ESD band.

• International journal of advanced smart convergence
• /
• v.10 no.4
• /
• pp.241-255
• /
• 2021

The human auricle is the first part to receive sound from the outside. In this part, the frequency range of human recognizable form is divided and organized. In this study, we propose modeling by applying a single sound source to the surface of the human auricle. This means that when the sound pressure of a low frequency (low frequency) sound enters the pinna, the impedance felt at the tip of a part of the non-linear surface of the pinna is mainly due to the tensile force at the end of the part of the non-linear surface of the pinna. By expressing the situation of moving at a very small speed, the characteristic impedance of the pinna was confirmed to be negative infinity, and it was also confirmed that the speed at the tip of a part of the non-linear surface of the pinna was 0 in the anti-resonance state. It was found that the wave propagation phenomenon that determines the characteristics of the filter is determined by how large the wavelength, kL, is compared to the length of the tip of a part of the non-straight surface of the pinna. Humans first receive sounds from outside through their ears. The auricle is non-linear and has a curved shape, and it is known that it analyzes frequencies while receiving external sounds. The human ear has an audible frequency range of 20Hz - 20,000Hz. Through the study, we applied the characteristics of the notch filter to hypothesize that the human audible frequency range is separated from the auricle, and applied filter theory to analyze it, and as a result, meaningful results were obtained. The curved part and the inner part of the auricle function as a trumpet, collecting sounds, and at the same time amplifying the weak sound of a specific band. The point was found and the shape of the envelope detected in the auricle was found. Selectivity for selecting sounds coming from the outside is the formula of the pinna that implements the function of Q. The function of distinguishing human-recognizable sound from the pinna from low to high through frequency analysis is performed in the pinna, and the 2-3kHz area, where human hearing threshold is the most sensitive, is also the acoustic impedance of the most recessed area of the pinna. It can be seen that starting from.