• Tribology and Lubricants
• /
• v.18 no.3
• /
• pp.194-203
• /
• 2002

This paper is the first step fur thermo-mechanical stress analyses of part with coated layer under contact load. A lot of coated material is applied in many structures to endure severe situation, like thermal stresses, high temperature gradients, irradiation, impacts by microscopic meteorites, and so on. In this part we are going to apply the FEM to analyze space parts with a coated layer subjected to a contact load thermo-mechanically. Coating layer is very thin in comparision with the structure, therefore it should take more times and behaviors to analyze whole model. In these reason we develop the FEM method of analyzing part with coated layer under contact load using partial model. Steady state temperature distribution of the part is obtained first, and then we apply quasi-static external load on the part. To obtain the final stage of solution, we compute the total solution, and by subtracting the thermal strain from the total ones we get the mechanical strains to compute stresses of the parts. In using the FEM, one has to discretize the model into many sub-domain, finite elements. The method is consisited of two steps. First step is to analyze the whole model with rather coarse meshes. Second step we cut a small region near the loading point, and analyze with very fine meshes. This method is allowable by the Saint-Venant's principle. And then, we finally shall check the therma1 load on the stresses of the space part with coating layer with or without substrate cracks. Then, we predict the actual behaviors of the part used in space.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.2
• /
• pp.93-100
• /
• 2013

Two-step thermochemical cycle using ferrite-oxide($Fe_2O_4$) device was investigated. The $H_2O$(g) was converted into $H_2$ in the first experiment which was performed using a dish type solar thermal system. However the experiment was lasted only for 2 cycles because the metal oxide device was sintered and broken down. Another problem was that the reaction was taken place mainly on a side of the metal oxide device. The m-$ZrO_2$, which was widely known as a material preventing sintering, was applied on the metal oxide device. The ferrite loading rate and the thickness of the metal oxide device were increased from 10.67wt% to 20wt% and from 10mm to 15mm, respectively. The chemical reactor having two inlets was designed in order to supply the reactants uniformly to the metal oxide device. The second-experiment was lasted for 5 cycles, which was for 6 hours. The total amount of the $H_2$ production was 861.30ml. And cerium oxide($CeO_2$) device was used for increasing $H_2$ production rate. $CeO_2$ device had low thermal resistance, however, more $H_2$ production rate than $Fe_2O_4$ device.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.983-989
• /
• 2011

A numerical algorithm for predicting fretting wear was developed using the boundary element method (BEM). A contact analysis was performed numerically using the relation between the elastic displacement and uniformly distributed loading of a rectangular patch on a semi-infinite solid. Geometrical updating based on nodal wear depths was performed. The wear depths were computed using the Archard's equation for sliding wear. In order to investigate the efficiency of BEM for predicting fretting wear, a problem involving a two-dimensional cylinder on a flat contact was analyzed, comparing it with the simulation model proposed by McColl et al. that was based on the finite element method. The developed method was then applied to the analysis of a spherical contact and it was shown that the developed simulation technique could efficiently predict fretting wear. Moreover, the effect of a step cycle on the solution obtained by the developed method was investigated.

• Preventive Nutrition and Food Science
• /
• v.1 no.1
• /
• pp.87-92
• /
• 1996

This study describes a stable and simple method for the measurement of cholesteryl ester transfer protein(CETP) activities using reconstituted HDL and LDL as substrates. Apolipoproteins (apo) A-I and -B were purified from hog plasma by a new strategy without ultracentrifugation and delipidation. a simple two-step column chromatography was administered. In the first step of phenyl-sepharose CL-4B column chro-matography, hydrophobic plasma proteins were isolated. The most hydrophobic proteins bound to the column appeared to be A-I and apo-B. Contaminat proteins were efficiently eliminated from the sample by washing the column with 0.3M NaCI containing buffer after loading the plasma on the column. Two pure proteins showing each single band on SDS-PSGE of apo A-I and apo-B were individually obtained by a subsequent gel filtration column chromatography(Sephadex G-200). This two-step purification was simple and inexpensive compared to the ultracentrifugation and/or delipidation method that are most commonly used. Reconstituted hight-density lipoproteins(HDL) and low-density lipoproteins(LDL) were prepared using the purified apo A-I and-B, respectively. When these artificially prepared HDL and LDL were used in the assays for CETP as the cholesteryl ester(CE) donor and acceptor respectively, the specific transfer of CE increased up to two fold compared to that used the native HSL and LDL.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.2
• /
• pp.123-132
• /
• 2012

Pre-pulping extracts were found to contain a dilute amount of xylo-oligosaccharides and acetic acid as the major components, and many minor components including other organic acids, lignin-derived phenolics, and sugar degradation products. Once separated from the pulp, a secondary hydrolysis step was required to hydrolyze oligomeric hemicellulose sugars into monomeric sugars before fermentation. The following study detailed the extent of hemicellulose recovery by pre-pulping using hot water extraction and characterized the hydrolysis of the extract with respect to comparing acid and enzymatic hydrolysis. The secondaryhydrolysis of hot water extracts made at an H-Factor of 800 was tested for a variety of acid and enzyme loading levels using the sulfuric acid and xylanases. The maximum fermentable sugar yield from acid and enzyme hydrolysis of the extract was 18.7 g/${\ell}$ and 17.7 g/${\ell}$ representing 84.6% and 80.1% of the maximum possible yield, respectively.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.712-718
• /
• 2005

In this study, a translator for transferring structural analysis data among commercial structural analysis programs was developed. The translator adopted the neutral format type based on ISO standard STEP AP 209 not only for the international standardization and robustness but also for the efficient management of structural analysis data Additional load entity is developed and added to AP 209 for the prevention of loss of information in retrieving exact loading condition. A modulization which is needed for efficient management and extension of the translator was made for the encapsulation of file format of each commercial code. Pilot tests peformed with 3-D frame analysis data of Sung-su bridge show that the developed translator guarantees the integrated management of analysis information as well as the exact transferring and retrieving of analysis data and related information.

• Journal of Industrial Technology
• /
• v.17
• /
• pp.119-124
• /
• 1997

This thesis is an experimental research of shear behavioral characteristics and shear behavioral coefficient of weathered residual soil which is mostly contained in soil of Korea. Using the weathered residual soil from mountain near Kangwon National University, this experimental research were contained the physical properties of sample in term of the basic test method such as specific gravity, plastic and liquid limit, grain-size distribution, density and water content. Experimental results obtained from direct shear test sand triaxial compression tests show that according to step loading, linear strain and linear stress increase continually and angle of internal friction decreases just little according to incresing of water content in case of ignoring the cohesion, and angle of internal friction appears the maximum angle near a optimum moisture content in case of considering the cohesion.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.113-118
• /
• 2001

The two-girder composite bridge has the girder space of more than 5m, for special case, over than 15m. Therefor, the design and construction of this bridge system require new approaches. To ensure the structural safety, the deck depth should be increased. Therefore, the economically designed deck system is necessary for th two-girder bridge. This study is the first step to develop the deck system for two-girder bridges. In this study, a literatute survey is performed to develop a new deck system for two-girder type of bridges. By considering the characteristics of two-girder bridge system, a cast-in-place PSC deck is proposed for the two-girder bridges. To examine structural behavior and safety of the proposed PSC deck, three real scale partition deck(3m$\times$5m) are tested under the static loading. In the test, the failure mode and behavior of each specimen, and ultimate load carrying capacity of the two-girder-bridge deck are identified.

• Journal of Sensor Science and Technology
• /
• v.21 no.4
• /
• pp.311-317
• /
• 2012

Disposable amperometric screen-printed biosensor strips have been fabricated by a sol-gel encapsulation for the analysis of glucose. The glucose oxidase(GOx) is entrapped in the gel matrix through sol-gel transition of tetraethoxysliane(TEOS). The biosensor is fabricated by GOx containing thin film of TEOS gel on the surface of screen-printed carbon electrode(SPCE). The GOx-containing thin film of TEOS gel offers a one-step modification process on the surface of SPCE. The optimum conditions for glucose determination have been characterized with respect to the applied potential, enzyme loading ratio, and pH. The linear range and detection limit of glucose detection were from 2.0 mM to 16.0 mM and 0.25 mM, respectively.

• Journal of KSNVE
• /
• v.11 no.3
• /
• pp.471-476
• /
• 2001

This paper focuses on the numerical prediction of airflow-induced sound in DVD drives. As a first step, computational fluid dynamics (CFD) is conducted to evaluate flow field characteristics due to the high-speed disk rotation, and to support the acoustic analysis. Acoustic analogy based on Ffowcs Wi1liams-Hawkings (FW-H) equation is adopted to predict aeroacoustic noise patterns. The integral solution for quadrupole volume source is included to identify the turbulence noise generated inside the DVD tray. The strength of sound pressure revel with respect to rotating speed is discussed to meet upfront demand on the high fidelity product development. The present study also focuses on the noise directivity and examines how much the sound noise is sensitive to change in rotating speed. Near-field noise is strongly affected by the flow field characteristic, which is caused by the complex shape of the tray. For a mid-field, the quadrupole noise play as a counterpart of thickness noise or loading noise, so it generates different sound noise Patterns compared with those in the near field.