• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.959-961
• /
• 2004

A multi pole SRM(switched reluctance motor) is applied by the regulated current in regular sequence. So, it can be started by itself. But a single phase SRM can not be started by itself because the positive torque is only generated in the limited zone which the inductance is increased. Therefore, it is required auxiliary device for self starting which place the rotor in start position. The prototype was designed and fabricated in the previous research. It has the permanent magnet, which is installed in the bottom of the rotor, for self starting. But the permanent magnet affect the prototype during operation and cause the decrease of the torque and speed. The influence of the permanent magnet on the average torque and speed was already confirmed. On this paper, the instant torque of the prototype was calculated from the experiment results which is the inductance and current according to installed permanent magnet or not.

• Proceedings of the KIEE Conference
• /
• 2007.04c
• /
• pp.198-200
• /
• 2007

A linear generator driven by hydrogen (or other kind of fuel) combustion engine requires special consideration for starting because of its none-conventional way of operation. This study investigates the possibility of replacing mechanical (hydraulic) start-up with electrical motoring. Simulation study based on 1 kW prototype system shows that the mover position of a linear generator can be controlled with a proper current control of power converter.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.10
• /
• pp.492-496
• /
• 2005

An electronic ballast with automatic identification between HPS and MH lamps is proposed in this paper. The behavior of the lamp impedance is studied at both cold-starting and warm-starting. Lamp identification is carried out by taking into account the rate of impedance changing at constant current driving mode just after ignition. The ballast consists of 8-bit microcontroller and LCC resonant inverter.

• Proceedings of the KIEE Conference
• /
• 2006.07e
• /
• pp.33-34
• /
• 2006

When high-voltage motors are started, inrush current is rising as a serious power quality problem in terms of electric power line. So, this study is measured electrical data from induction motor's various starting method and is proposed the most appropriate starting method for induction motor at WTPs.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.523-529
• /
• 2013

A sensorless speed control of a permanent magnet synchronous motor(PMSM) which utilizes MRAS based scheme to estimate rotor speed and position is presented. Considering an error between real and estimated rotor position values, a state equation of PMSM in the synchronous d-q reference frame is represented. A state equation of model system which uses estimated speed and nominal parameter values is expressed. To minimize the errors between the derivatives of d-q axis currents of real and model system, MRAS based adaptation mechanisms for the estimation of rotor speed and position are derived. On the other hand, for the acceleration stage of motor just before the sensorless operation, an acceleration scheme using only d-axis current control is proposed. To show the validity of the proposed scheme, experimental works are carried out and evaluated. During acceleration stage, the acceleration scheme using only d-axis current command shows good acceleration performance and controlled current level. For the sensorless operation, at low speed (5% of rated speed), a good performance is observed.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.4
• /
• pp.62-70
• /
• 1995

Brushless DC Motor (BDCM) is widely used in the industry such as a variable speed motor in a compressor for room air conditioners, because the motor can be easily controlled and operated over a wide speed range. The system to drive BDCM needs encoder that senses rotor position. Gut in a certain application, the position sensor has to be avoided. In the paper, various position sensorless drive systems for BDCM are investigated and critically evaluated, so that the effective method of sensorless control can be selected. Out of these methods, the freewheeling diode current sensing has many advantages. For example, the simple starting procedure makes it possible to perform sensorless control even in low speed. So the hardware design for this method has been carried out and the system has been implemented using DSP. The experimental results verified that the freewheeling diode current sensing approach has advantages in starting procedure and low speed sensing.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.87-92
• /
• 2013

In high-speed train, the EMI is generated by pantograph detachment and switching device of motor-block. Especially, the conductive noise flows through rail as return feeder influences unintended results to sub-station, transformer, etc. These phenomena were investigated by PSIM circuit analysis tool and each part of railway system is modeled by circuit elements and switching devices. Consequently, the distorted wave in return feeder current occurs by the high speed switching frequency, and the overvoltage is applied by the pantograph detachment. Also the distortion of return current is high in starting point and it decreases from the proximity of a starting point ro the end of terminal.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.369-374
• /
• 2011

An induction motor operated with high voltage source generally generates high current in starting mode and has a long transient time after being started. This large and sustaining starting current causes the end windings of the stator to have excessive electromagnetic force. This force is the source of vibration and has a negative and serious influence on the insulation of end windings. Therefore, designing the end winding part with an appropriate support system is needed. To design the support ring enclosing the end windings, we analyze the distribution of electromagnetic force on the end windings by applying the Biot-Savart's law and the 3D finite element method (FEM), and comparing two simulation methods. Finally, we verify the safety of the support structure of the end winding part using stress analysis, which is analyzed with the electromagnetic forces from the 3D FEM simulation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.12
• /
• pp.592-600
• /
• 2001

This Paper presents the transient analysis of the single-phase line-start permanent magnet synchronous motor. To analyse the starting characteristics, the dynamic equation which is combined electric dynamic equations with mechanical dynamic equation is used. The electric dynamics are derived from the d-q axis voltages of stator and rotor respectively. Especially, symmetrical components transformation is used to consider unbalanced magnetic field which is produced by single-phase input. Non-linear d-q axis inductances according to current amplitude and current phase angle are calculated by Finite Element Method and applied to lumped parameter circuit. The analysis methods are validated by comparing simulated and experimental results.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.2
• /
• pp.220-220
• /
• 1999

This paper describes the high efficiency inverter ballast circuit using very cheap microprocessor, which has been developed by the author. A variety of soft-switching techniques have been proposed to reduce the switching losses and EMI problems that occur with higher switching frequencies in switched inverter ballast. The inverter ballast circuit, which employs a temperature sensing circuits has been also proposed to improve starting performance of the fluorescent lamps. That is, the inverter ballast circuit, which employs a soft-starting circuit and soft-switching techniques to implement the power factor correction and to mitigate of power-loss and increase a life time of the fluorescent lamps, has become an attractive performance for ballasting the fluorescent lamps. In this paper, the operation and the control of the inverter ballast are described in detail and experimental results are presented. As the experimental results, when environment temperature is at -40℃, the inverter ballast circuit has low THD(4.8%) of the input current and large power factor(98%) of the lamp current. The proposed improved ballast circuit appears to be a good performance for ballasting fluorescent lamps.