• 제목/요약/키워드: Standard Wall

검색결과 663건 처리시간 0.025초

철근콘크리트 내진벽의 구조성능 평가 및 개선 (Evaluation and Improvement of Structural Performance of Reinforced Shear Walls Under Load Reversals)

  • 신종학;하기주;안준석;주정준
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
    • /
    • pp.683-688
    • /
    • 1999
  • The purpose of this study is to develop and evaluate the structural performance of various shear walls, such as the hysteretic behavior, the maximum horizontal strength, crack propagation, and ductility etc. under load reversals. For the diagonal reinforced slit and infilled shear wall specimens, it was found that the failure mode shows very effective crack control and crashing due to slippage prevention of boundary region and reduction of diagonal tension rather than the brittle shear and diagonal tension failure. The ductility of specimens designed by the diagonal reinforcement for the slit and infilled shear wall was increased 1.72~1.81 times in comparison with the fully rigid shear wall frame. Maximum horizontal load-carrying capacity of specimens designed by the diagonal reinforcement ratio the slit and infilled shear wall was increased respectively by 1.14 times and 1.49 times in comparison with the standard fully rigid shear wall frame.

  • PDF

정적 수평하중에 의한 경량벽체의 최대변형량 허용기준에 관한 연구 (Permissible Criteria of the Stiffness of Lightweight Wall by the Horizontal Static Load)

  • 송정현;김기준;최수경
    • 한국건축시공학회:학술대회논문집
    • /
    • 한국건축시공학회 2014년도 춘계 학술논문 발표대회
    • /
    • pp.204-205
    • /
    • 2014
  • Among common test methods of assessing structure safety for existing lightweight walls, the criteria of the quality assessment of the horizontal static load resistance has been considered ambiguous. In the current study, therefore, an experiment was conducted to figure out the standardized assessment criteria of the lightweight wall's horizontal static load resistance. Based on the findings of the experiment with gypsum board and ALC block walls, an acceptable amount of each standard and the variables of the stud wall arising from the appropriate load (1000N) on the wall in a daily life were accounted for, arbitrarily setting the maximum deformation amount below 15mm.

  • PDF

알루미늄 커튼월의 ASD/LRFD설계방법에 따른 경제성 평가 방법 (Economic Evaluation Method by Design Method ASD and LRFD of Aluminum Curtain wall)

  • 문상덕;옥종호
    • 한국건축시공학회:학술대회논문집
    • /
    • 한국건축시공학회 2014년도 춘계 학술논문 발표대회
    • /
    • pp.16-17
    • /
    • 2014
  • The curtain wall construction applied on high-rise building facades in Korea became generalized, but specialty of the CMr(Construction Manager) who needs to perform economical project management with specialty in the curtain wall construction is still lacking. Therefore, this study analyzed the structure design standard of the curtain wall, researched economical design alternatives. Based on the research results, if the ratio of dead load against wind load is less than 0.1256, LRFD will be more economical.

  • PDF

저레이놀즈수 2차 모멘트 난류 열유속모형 개발에 관한 연구 (A Low-Reynolds Number Second Moment Closure for Turbulent Heat Fluxes)

  • 신종근;최영돈;이건휘
    • 대한기계학회논문집
    • /
    • 제17권12호
    • /
    • pp.3196-3207
    • /
    • 1993
  • A second moment turbulent closure for the turbulent heat flux near a wall is developed by modification of model constants in pressure interaction term as the variables of the turbulent Reynolds number using the universal properties of turbulent heat flux near the wall. The present model shows that model constant for the wall reflection term in pressure interaction is most important in modelling of the near wall heat flux. Fully developed pipe flows with constant wall heat flux are tested to validate the proposed model. In most of calculation region, the predicted turbulent properties agree better with the experimetal data than the results from standard algebraic heat flux model which use the uniform model constants.

Curtain-wall공사에 있어서 Mock-up Test 건축공사표준시방서의 개선 방안에 관한 연구 (A study on the improvement of The standard specifications for Mock-up Test in the Curtain-wall construction)

  • 이진만;강재왕;손용근;김창덕
    • 한국건설관리학회:학술대회논문집
    • /
    • 한국건설관리학회 2003년도 학술대회지
    • /
    • pp.491-494
    • /
    • 2003
  • 외벽을 형성하는 Curtain-wall은 비, 바람 등 자연의 기후 조건 및 주번 여건에 충분히 견딜 수 있도록 설계, 제작, 시공되어야 한다. 그러므로 전반적인 성능을 확인하기 위한 Mock-up Test는 최근에 들어서 고층 건물 및 중요도가 높은 경우 거의 일반화가 된 상황이다. 그러나 현재 Mock-uP Test의 시방서는 외국에 비해 미약하여 시방서 상으로 인한 분쟁사례가 많이 발생하고 있다. 또한 시방서 상의 표현에 있어서 불명료함으로 인하여 적용함에 있어 문제가 발생하고 있다. 따라서 현 Mock-up Test 시방서에 대한 조사를 통해 그 문제점들을 살펴보고 외국의 사례와 비교 검토하여 그 개선방안에 대한 검토를 해보고자 한다.

  • PDF

알루미늄칩과 타공판을 이용한 방음벽 충진재의 흡음특성 (Absorption Characteristics of Sound Proof Wall by Scrap Aluminum and Perforated Plate)

  • 이영중;김대건;박경화;김영도
    • 한국재료학회지
    • /
    • 제19권7호
    • /
    • pp.382-385
    • /
    • 2009
  • Efforts to reduce noise in industrial application fields, such as automobiles, aircrafts, and plants have been gaining considerable attention while a sound proof wall to protect people from the noise has been intensively investigated by many researchers. In this study, our research group suggested creating a new sound proof wall composed of scrap aluminum chips and perforated plates in a commercial polyester sound proof wall, which was then successfully fabricated. This wall's sound absorption characteristics were measured by an impedance tube method. The sound absorption property was evaluated by measuring the Noise Reduction Coefficient (NRC) to the standard, ASTM C 423-90a. The noise reduction coefficient of the sound proof wall composed of 3.5 vol.% and 7.5 vol.% of scrap aluminum chips relatively increased to 5% and 8% compared to the commercial polyester sound proof wall. The scrap aluminum perforated plate also relatively increased to 13% compared to the commercial polyester sound proof wall.

Insights from LDPM analysis on retaining wall failure

  • Gili Lifshitz Sherzer;Amichai Mitelman;Marina Grigorovitch
    • Computers and Concrete
    • /
    • 제33권5호
    • /
    • pp.545-557
    • /
    • 2024
  • A real-case incident occurred where a 9-meter-high segment of a pre-fabricated concrete separation wall unexpectedly collapsed. This collapse was triggered by improperly depositing excavated soil against the wall's back, a condition for which the wall segments were not designed to withstand lateral earth pressure, leading to a flexural failure. The event's analysis, integrating technical data and observational insights, revealed that internal forces at the time of failure significantly exceeded the wall's capacity per standard design. The Lattice Discrete Particle Model (LDPM) further replicates the collapse mechanism. Our approach involved defining various parameter sets to replicate the concrete's mechanical response, consistent with the tested compressive strength. Subsequent stages included calibrating these parameters across different scales and conducting full-scale simulations. These simulations carried out with various parameter sets, were thoroughly analyzed to identify the most representative failure mechanism. We developed an equation from this analysis that quickly correlates the parameters to the wall's load-carry capacity, aligned with the simulation. Additionally, our study examined the wall's post-peak behavior, extending up to the point of collapse. This aspect of the analysis was essential for preventing failure, providing crucial time for intervention, and potentially averting a disaster. However, the reinforced concrete residual state is far from being fully understood. While it's impractical for engineers to depend on the residual state of structural elements during the design phase, comprehending this state is essential for effective response and mitigation strategies after initial failure occurs.

난류 흐름의 RANS 수치모의를 위한 벽함수 성능 평가 (An evaluation of wall functions for RANS computation of turbulent flows)

  • 유동근;백중철
    • 한국수자원학회논문집
    • /
    • 제53권1호
    • /
    • pp.1-13
    • /
    • 2020
  • 높은 레이놀즈수를 갖는 공학적인 흐름을 예측하는 가장 일반적인 방법은 여전히 벽함수를 이용하는 난류모형에 근거한 RANS 수치모의이다. 최근 벽근처의 점성영역 관계식과 벽에서 떨어진 대수영역 관계식을 혼합하여 개발된 일반화된 벽함수들은 두 영역사이의 난류량과 유속이 부드럽게 천이하도록 한다. 이 연구는 난류운동에너지(TKE), 에너지 소산율, 비소산율, 와점성에 대해서 적용 가능한 벽함수들을 조합하여 일련을 수치 모의를 수행하여 널리 이용되고 있는 난류모형들의 성능과 수렴 특성을 분석하였다. 이 연구 결과는 RNG k-𝜖 모형의 경우 첫번째 계산격자가 완충층에 놓이게 될 때는 반복 계산시 작은 허용오차를 이용하여 주의 깊게 적용을 하여야 안정된 해를 구할 수 있음을 보여준다. 표준 k-𝜖과 RNG k-𝜖 모형은 TKE와 와점성에 대해서 적용 가능한 벽함수들 중 어느 것을 선택하여 적용하더라도 수치모의 결과가 민감하게 반응하지 않는 것으로 나타났다. 한편, k-ω SST 모형의 경우 TKE에 대해서는 kL-벽함수 그리고 와점성에 대해서는 nutUB-벽함수를 이용하여야 정확하고 안정된 경계 조건 설정을 보장할 수 있다. 레이놀즈수 155,000조건에서 적용한 후방계산흐름 수치모의 결과 격자 해상도에 상관없이 약 13% 정도 재부착 거리를 과소평가하는 모형을 제외하고 나머지 적용한 난류모형들 모두 적절히 세밀한 해상도의 격자에서 양호하게 재부착거리를 잘 예측하는 것으로 나타났다.

농촌주택 및 목조주택 표준모델 구조체의 습·열 환경 성능 개선 방안 (Hygrothermal Performance Improvement Plan of Standard Model for Rural Housing and Wooden Housing)

  • 유동완;이태구
    • 한국농촌건축학회논문집
    • /
    • 제23권4호
    • /
    • pp.63-71
    • /
    • 2021
  • The purpose of this study was to investigate whether the standard models for rural housing and wooden housing model have performance for hygrothermal and to propose a way of improvement relevant to hygrothermal performance for those models. All of the models to be analyzed were found to have some parts that were absent of stability in terms of performance for hygrothermal. In the process of analyzing the causes and proposing improvement measures, the following conclusions were derived. Fist, The exterior surface of the structure should be composed of a structure with good moisture permeability, and for the interior surface, a variable vapor retarder paper should be applied in consideration of the reverse condensation phenomenon in summer. Second, in terms of performance for hygrothermal, applications of external insulation plaster finish to the exterior wall or of ventilation method using a rafter vent on the roof should be avoided. Third, a rain screen method with a ventilation layer should be applied to the exterior wall, and a method of constructing ventilation layer separated from the insulation layer with a vapor retarder paper should be applied to the roof. Fourth, the application of insulation materials having capillary action, such as wood fiber insulation board or cellulose insulation board, contributes to more stable performance for hygrothermal.

워터스촬영법과 파노라마촬영법을 이용한 상악동염에 관한 방사선학적 연구 (A RADIOLOGIC STUDY OF THE MAXILLARY SINUSITIS AS SEEN BY WATERS′ AND SPECIALIZED PANORAMIC PROJECTIONS)

  • 고광준
    • 치과방사선
    • /
    • 제17권1호
    • /
    • pp.259-269
    • /
    • 1987
  • The purpose of this study was to evaluate the specialized Orthopantomograms and standard films compared with Waters' views in the diagnosis of maxillary sinusitis. The author analysed the types of mucosal thickening, the types of bony wall change, the relation between the types of chief complaints and mucosal thickening on the Waters' views of 156 patients with 206 maxillary sinuses demonstrating radiographic changes. And the pathologic change of antral floor was observed on 187 standard films and total amount of agreement in the diagnosis of maxillary sinusitis was evaluated at 156 specialized Orthopantomograms and 187 standard films. The results were obtained as followings. 1. Among 206 mucosal thickenings classified by 6 types, generalized increased radiopacity was 69 cases (33.5%) and the entire thickening of mucosa except an ostium area was 66 cases (32.0%), 2. The bony wall change was seen in 128 cases (62.1%) and the incidence of indistinct antral wall was the highest as 55 cases (43.0%) among 5 types. 3. Among 148 chief complaints, pain was 71 cases (48.0%), swelling was 19 cases (12.8%) and discomfort was 18 cases (12.2%). 4. The most frequent change of antral floor was indistinct antral floor as 25 cases (13.4%) and elevation of antral floor was 23 cases (12.3%). And the first molar presented the most frequent involvement of antral floor as 47 cases (57.3%). 5. In 156 specialized Orthopantomograms, 101 cases (49.0%) presented apparent increased radiopacity and 72 cases (35.0%) showed suspicious increased radiopacity in comparison with Waters' view. In 187 standard films, 47 cases (25.1%) presented apparent increased radiopacity and 53 cases (28.4%) showed suspicious increased radiopacity in comparison with Waters' views.

  • PDF