• Advances in concrete construction
• /
• 제8권4호
• /
• pp.277-283
• /
• 2019

In evaluating explosion-protection capacity, safety distance is broadly accepted as the distance at which detonation of a given explosive causes acceptable structural damage. Safety distance can be calculated based on structural response under blast loading and damage criteria. For the applicability of the safety distance, the minimum required stand-off distance should be given when the explosive size is assumed. However, because of the nature of structures, structural details and material characteristics differ, which requires sensitivity analysis of the safety distance. This study examines the safety-distance sensitivity from structural and material property variations. For the safety-distance calculation, a blast analysis module based on the Kingery and Bulmash formula, a structural response module based on a Single Degree of Freedom model, and damage criteria based on a support rotation angle were prepared. Sensitivity analysis was conducted for the Reinforced Concrete one-way slab with different thicknesses, reinforcement ratios, reinforcement yield strengths, and concrete compressive strengths. It was shown that slab thickness has the most significant influence on both inertial force and flexure resistance, but the compressive strength of the concrete is not relevant.

• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.28-34
• /
• 2004

The old technique of sandblasting which has been used for decoration of glass surface has recently been developed into a powder blasting technique for brittle materials such as glass, silicon and ceramics, capable of producing micro structures larger than 100${\mu}{\textrm}{m}$. In this study, we introduced oblique powder blasting, and investigated the effect of the impacting angle of particles, the scanning times and the stand-off distance on the surface roughness and the weight-loss rate of samples with no mask, and the wall profile and overetching of samples with different mask pattern in powder blasting of soda-lime glass. The varying parameters were the different impact angles between 50$^{\circ}$ and 90$^{\circ}$, scanning times of nozzle up to 40 and the stand-off distances 70mm and 100mm. The widths of mask pattern were 0.2mm, 0.5mm and 1mm. The powder was alumina sharp particles, WA #600. The mass flow rate of powder during the erosion test was fixed constant at 175g/min and the blasting pressure of powder at 0.2Mpa.

• 한국군사과학기술학회지
• /
• 제25권3호
• /
• pp.275-284
• /
• 2022

Linear Shaped Charge(LSC) is widely used as a separation system in the field of weapon system. However, there are some disadvantages that are charging lots of explosives due to lack of uniformity and having difficulties of the design of liner and explosives because of manufacturing process. In order to solve these problems, Precision Linear Shaped Charge(PLSC) that can design a liner independently and charge explosives uniformly has been developed. In this study, PLSC was designed to have a proper liner shape and amount of explosives, and the penetration test of PLSC with different stand-off distance from liner to target was conducted. On the basis of the penetration test results of PLSC, the numerical analysis method using AUTODYN was established and verified. The penetrative mechanism and characteristics of PLSC with targets of different materials was analyzed from experimental and numerical results.

• 화약ㆍ발파
• /
• 제20권3호
• /
• pp.15-23
• /
• 2002

철골구조물은 일반 철근 콘크리트 구조와는 달리 단순히 천공을 하고 폭약을 장약하여 기폭시키는 방법으로는 해체 또는 절단이 어렵다. 국내의 경우 최근 철골 구조로 건축되는 강교와 건축물 등이 증가하는 추세이며, 내구연한이 다하거나 구조적 결함으로 인하여 해체 대상으로 지목되는 철골구조물에 대해서는 특수한 형태의 해체 기술을 필요로 한다. 1997년 이후 국내에 철골구조물의 발파해체를 위하여 성형폭약에 의한 폭발절단기술에 관한 연구가 소개된 이후로 폭발절단력에 미치는 성형폭약의 라이너(Liner), 폭약의 종류, 형상 및 이격거리(Stand-off distance) 등에 대한 연구가 활발히 이루어졌으며, 또한 국산화를 위한 기초적인 설계변수에 관한 연구 등이 보고 된 바 있다. 현재 성형폭약의 사용범위가 철골구조물의 절단해체 뿐만 아니라 긴급구조를 필요로 하는 특수한 용도나 군사폭약의 해체, 항공산업 등 그 적용범위가 확대되고 있는 실정이다. 그러나, 성형폭약의 성능 향상 및 품질 보증을 위한 체계적인 설계 변수의 검토 설정에 관한 연구와 산업f'의 적용을 위한 구체적인 결과는 보고 된 바 없는 실정이다. 그래서, 보다 체계적인 현장 적용 시험 등에 대한 연구가 효율적으로 진행될 경우 국내 고유 기술에 의한 철구조물의 절단 및 해체공법에 획기적인 변화를 가져올 수 있을 것으로 기대된다. 따라서, 본 연구에서는 국산화되어 현장에 적용되고 있는 성형폭약 HAKO 제품을 기준으로 이미 국내에 알려진 성형폭약과 비교 분석하였다. 또한 보다 효율적인 산업계의 적용을 위한 각종 시험 결과 및 국산화 현황과 향후 활용 방안 등에 대하여 소개하고자 한다.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.641-646
• /
• 2016

The effects of water addition on $Y_2O_3$ coatings or thick films prepared by plasma suspension spray (SPS) have been investigated. Water addition in suspension media was found to be effective to control the color of a $Y_2O_3$ coating prepared by SPS. The color changed with water addition at the shortest stand-off distance of 50 mm even if samples had the same crystalline phase. Change was not correlated with fragmentation behavior of liquid suspension inside the plasma jet. Water content over 50 vol% was found to produce unmelted particles, indicating that water suppressed heat transfer to the particles. However, plasma jet temperature was not affected. Instead, the coating fabricated with water addition has higher oxygen and lower carbon content compared to these characteristics of the coating without water addition. This was attributed to the retarded complete evaporation of liquid media from the suspension droplet, resulting in inhibition of excessive heating and evaporation of the molten $Y_2O_3$ droplet. In this regard, crystalline phase development with respect to stand-off distance and water addition was discussed.

• 한국연소학회지
• /
• 제1권2호
• /
• pp.41-49
• /
• 1996

A numerical study is conducted to investigate the periodically unstable shock induced combustion around blunt bodies in stoichiometric hydrogen-air mixtures. Euler equations are spatially discretized by upwind-biased third order scheme and temporally integrated by Runge-Kutta method. Chemistry model used in this study involves 8 elementary kinetics steps and 7 species. At a constant Mach number, the effects of projectile size, inflow pressure and inflow temperature are examined with Lehr#s experimental condition as a reference. In addition to oscillation frequency, characteristic distances and time averaged values are found from the result to find an relation with dimensionless parameters. As a result, it is found that the effects of inflow pressure and body size are very similar and $Damk{\ddot{o}}hler$ number plays an important role in determining the instability characteristics.

• 한국항공우주학회지
• /
• 제47권6호
• /
• pp.397-404
• /
• 2019

항공우주시스템에서 절단/분리 시스템에 널리 사용되는 선상성형장약은 복합화약 충전량의 불균일로 인해 과량의 복합화약을 충전해야 하며 제작 공정의 특성상 라이너 및 복합화약 형상을 자유자재로 조절하기 어렵다는 단점을 가지고 있다. 이를 개선하기 위하여 라이너를 단독으로 제작하여 균일한 복합화약량을 충전할 수 있는 정밀선상성형장약에 대한 연구 개발이 진행되고 있다. 본 연구에서는 정밀선상성형장약이 적정 복합화약량을 갖도록 설계하고 설계된 정밀선상성형장약의 최적 침투 관통 성능을 확인하기 위하여 라이너로부터 표적까지의 거리에 단차를 두어 이격거리에 따른 침투 관통 성능시험을 수행하였다. 정밀선상성형장약의 침투 관통 성능시험 결과를 바탕으로 AUTODYN 기반의 수치 해석 환경을 구축하였다. 수치해석 및 시험 결과의 비교 분석을 통해 정밀선상성형장약의 침투 관통 메커니즘과 특성을 분석하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.520-523
• /
• 2002

The o]d technique of sandblasting which has been used for paint or scale removing, deburring, and glass decorating has recently been developed into a powder blasting technique for brittle materials, capable of producing micro structures larger than $100\mu\textrm{m}$. In this study, we investigated the effect of the size of abrasive and the stand-off distance on the machinability of SUS 304. The varying parameters were the impact angle $90^{\circ}$, scanning times of nozzle 10 and the different nozzle height between 70mm and 140mm. The diameter of dot pattern were 0.2mm. The powder were alumina sharp particles, WA #600, #800 and #2000. The blasting pressure of powder at 0.3 Mpa.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.379-382
• /
• 2004

Abrasive jet machining (AJM) has a large number of parameters such as powder flow rate, air pressure, diameter of abrasive, stand off distance, material hardness and fracture toughness, etc. It is not easy matter to control those parameter. To achieve high accurate machining, in this study, Taguchi method was used to select process parameters. The objective of the optimization was to get higher material removal rate (MRR). From the experiments and analysis, some process parameters were found to make efficient machining.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1108-1114
• /
• 1992

본 연구에서는 폭발용접 성능평가에 중요한 영향을 주고 있는 기폭방법을 비 교하고, 선형 충격파의 발생방법과 이에 의한 접합 결과를 실험적으로 나타내고자 한 다.