• Geomechanics and Engineering
• /
• v.12 no.1
• /
• pp.85-109
• /
• 2017

The paper presents the laboratory study of clayey soil stabilized with Pond ash (PA), Rice husk ash (RHA), cement and their combination used as stabilizers to develop and evaluate the performance of clayey soil. The effect of stabilizer types and dosage on fresh and mechanical properties is evaluated through compaction tests, unconfined compressive strength tests (UCS) and Split tensile strength tests (STS) performed on raw and stabilized soil. In addition SEM (scanning electron microscopy) and XRD (X-ray diffraction) tests were carried out on certain samples in order to study the surface morphological characteristics and hydraulic compounds, which were formed. Specimens were cured for 7, 14 and 28 days after which they were tested for unconfined compression tests and split tensile strength tests. The moisture and density curves indicate that addition of RHA and pond ash results in an increase in optimum moisture content (OMC) and decrease in maximum dry density (MDD). The replacement of clay with 40% PA, 10% RHA and 4% cement increased the strength (UCS and STS) of overall mix in comparison to the mixes where PA and RHA were used individually with cement. The improvement of 336% and 303% in UCS and STS respectively has been achieved with reference to clay only. Developed stabilized soil mixtures have shown satisfactory strength and can be used for low-cost construction to build road infrastructures.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.117-123
• /
• 2013

Since the nonlinear factors such as friction in a mechanical servo system can't be easily measured nor estimated accurately. Therefore, it is difficult to compensate friction correctly. Friction makes a significant error in a 2-axis stabilized gimbal system and finally fails to reach the ultimate control performance goals. To solve these problems, lots of studies on the control methods applying observer have been performed. However, these methods can be used in specific conditions and are limited to apply them to the accurate 2-axis stabilized gimbal system in military sector. This paper deals with the PI-LEAD algorithm which is modified with a general and robust PID algorithm, proves the effect of the algorithm through modeling and simulation, and verifies the performance by applying the algorithm to the real 2-axis stabilized system. It is verified through the performance test that the PI-LEAD algorithm minimizes the error caused by friction and meets requirements of the accurate servo system.

• Journal of the Korean Data and Information Science Society
• /
• v.21 no.1
• /
• pp.33-42
• /
• 2010

The purpose of this study was to identify cervical stabilized exercise and joint mobilization, the difference between them, and the maximum muscle strength and static muscle endurance of each group after the enforcement to general people. Cervical joint mobilization group refers to interarticular exercise (traction, pressure, glide) using with Kaltenborn technique. 3 classes were divided into 20 people each, cervical joint mobilization and stabilized exercise, and the comparison groups were randomized for the study. Both cervical stabilized exercise and joint mobilization increased maximum muscle strength and static muscle endurance. Patients should be able improve muscle stabilization and deep cervical muscle by using joint mobilization when the patient is unable to exercise on their own.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.473-480
• /
• 1999

This paper presents the results of a parametric study on the behavior of mechanically stabilized earth retaining wall. It has been recognized that the currently available design guidelines, which is base on the limit equilibrium approach, cannot properly account the interaction effect between the components, construction sequence, and foundation settlement which may impose a significant influence on the wall behavior. A parametric study using finite element analysis was performed to investigate the behavior of MSE wall under different construction conditions and the applicability of the current design approach. In the parametric analysis, the effects of the construction sequence, the surcharge, and the foundation stiffness were studied and a detailed finite element modeling for various components of the system were employed. The results, such as wall displacement and earth pressure distributions, reinforcement forces, vertical stress distribution were then thoroughly analyzed to investigate the effect of construction details on the wall behavior.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.63-70
• /
• 1990

In a premixed flame stabilized by a streamlined step, the flame structure and combustion characteristics were investigated to identify the effect of the pressure pulsation in a combustion air. A flame stabilizing limits, visualization, mean temperature, ion current and gas concentration (O$_{2}$, CO$_{2}$, CO, UHC) were measured. With the combustion air of higher pressure pulsation, the development of the mixing layer was fast and wide, the temperature and combustion intensity were higher at arbitrary section. But, the effect was notably decreased with X=150 mm downstream. And a first eddy formation from step edge was earlier. Thus, with the combustion air of higher pressure pulsation, high rate of heat generation was expected.

• Journal of Powder Materials
• /
• v.5 no.2
• /
• pp.111-121
• /
• 1998

Thick and dense deposit of higher than 97% of theoretical density was formed by induction plasma spraying. To investigate the effects of powder morphology on the density of deposit, two different kinds of Yttria-Stabilized-Zirconia powder, METCO202NS (atomized & agglomerated) and AMDRY146 (fused & crushed), were used and compared. After plasma treatment, porous METCO202NS powder was all the more densely deposited and its density was increased. In addition to the effect of powder morphology, the process parameters such as, sheath gas composition, probe position, particle size and spraying distance, and so on, were evaluated. The result of experiment with AMDRY146 powder, particle size and spraying distance affected highly on the density of the deposit. The optimum process condition for the deposition of -75 ${\mu}m$ of 20%-Yttria-Stabilized-Zirconia powder was 120/201/min of Ar/$H_2$ gas rate, 80 kW of plasma plate power, 8 cm of probe position and 150 Torr of spraying chamber pressure, at which its density showed 97.91% of theoretical density and its deposition rate was 20 mm/min. All the results were assessed by statistical approach what is called ANOVA.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.7-11
• /
• 2010

Yttria stabilized zirconia (Y-CSZ) single crystals show plastic deformation at high temperatures by activating dislocations. The effect of strain rate on the plastic behavior of this crystal was studied. As increasing strain rate from $\varepsilon=1.04\times10^{-5} sec^{-1}$ to $2.08\times10^{-5} sec^{-1}$ the yield drop was suppressed and resulted in higher Young's modulus and yield stress. Dislocation structures of the strained crystals were analyzed using a transmission electron microscope to elucidate the plastic behavior of these crystals. In the early stage of plastic deformation, dislocation dipoles and prismatic dislocation loops were formed in both samples. However, dislocation density was increased by increasing strain rate. Strong sessile dislocations were observed in the sample with higher strain rate, which may cause the higher work hardening.

• Journal of Korean Vacuum Science & Technology
• /
• v.2 no.1
• /
• pp.43-48
• /
• 1998

The effect of mcirostructure on the electrical properties of yttria stabilized zirconia (YSZ) was analyzed by modeling layer arrangements and mixed phase structure. The YSZ thin films were deposited by RF magnetron sputtering using 30mol% YSZ and 8 mol% YSZ targets with yttrium pellets on porous alumina substrates. The structure, composition and electricla properties of the YSZ films were investigated as functions of sputtering conditons and layer arrangements by XRD, TEM, XPS and acimpedance spectroscopy. The results showed that the triple palyered YSZ films had highermicrohardness, lower compressive stress state and higher ionic conductivity by one order than single and double layered YSZ films. However, sputtered YSZ films have low conductivity compared to YSZ pellets or doctor bladed YSZ thin plates. These results were probably due to the influence of insulating alumina substrates, impractical for most stacking geometries and inductance induced by relatively long platinum, lead wire on YSZ conductivity.

• Journal of ILASS-Korea
• /
• v.27 no.1
• /
• pp.18-25
• /
• 2022

Hot-firing tests were performed to experimentally confirm the effect of the eigenmode in the fuel-air mixing section on combustion instability by changing mixing section length, inlet mean velocity, equivalence ratio, and swirler geometry. A premixed gas composed of air and ethylene was supplied to the combustion chamber through an mixing section and an axial swirler. As the mixing section length increased, the inlet velocity perturbation decreased, but the combustion instability increased more. It was found that the resonance frequency of the first longitudinal mode in the mixing section shifted to the third longitudinal mode as the length of the mixing section increased. The results implied that the transition of the resonace frquency by changing the length of the mixing section might cause combustion instability.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.6
• /
• pp.776-783
• /
• 2004

The purpose of this study was to identify the reasonable gathering conditions as consider of effect of gathering and variation of silhouette made by gathering conditions. The experimental design consists of four factorial design: (1) three kinds of different weight and different thickness fabrics (2) three kinds of different stitch densities (3) five kinds of different ratio of gathers (4) three kinds of different angles. Therefore one hundred thirty five (135) samples were made. Data analysis utilize SPSS WIN 10.0 Package. The results of this study were as follows: 1. In the aspect of fabrics, it is shown the visual propriety that it is as thin as the small stitch, and as thick as the big stitch. 2. As stitch densities, it shows the different stabilized nodes. 3. In the aspect of ratio of gathers, it is shown the visual propriety that a few was small stitches, which help formations of nodes, and a lot were big stitches, which help increased the effect of gather. 4. In the aspect of angle of bias, the drape appearance was excellent as a sample of cutting by 0 angle(0$^{\circ}$) of bias. The big stitches that help formations of stabilized nodes, and a case of cutting by 45 angle(45$^{\circ}$) of bias was small stitch.