• 한국분말재료학회지
• /
• 제23권1호
• /
• pp.1-7
• /
• 2016

Cu-Mn compacts are fabricated by the pulsed current activated sintering method (PCAS) for sputtering target application. For fabricating the compacts, optimized sintering conditions such as the temperature, pulse ratio, pressure, and heating rate are controlled during the sintering process. The final sintering temperature and heating rate required to fabricate the target materials having high density are $700^{\circ}C$ and $80^{\circ}C/min$, respectively. The heating directly progresses up to $700^{\circ}C$ with a 3 min holding time. The sputtering target materials having high relative density of 100% are fabricated by employing a uniaxial pressure of 60 MPa and a sintering temperature of $700^{\circ}C$ without any significant change in the grain size. Also, the shrinkage displacement of the Cu-Mn target materials considerably increases with an increase in the pressure at sintering temperatures up to $700^{\circ}C$.

• 반도체디스플레이기술학회지
• /
• 제15권2호
• /
• pp.11-15
• /
• 2016

This paper, Ga-doped ZnO (GZO) thin films which were deposited on Corning glass substrate using an magnetron sputtering deposition technology and then the post deposition annealing process was conducted for 30 minutes at different temperature of 100, 200, 300, and $400^{\circ}C$, respectively. So as to investigate the properties for the relevant the Concentration and Oxygen Vacancy with Annealing temperature of Ga-doped ZnO thin films by RF Sputtering method. The Carrier concentration is enhanced as annealing temperature decreases, and also the oxygen vacancy concentration is enhanced as annealing temperature decreased. Oxygen vacancy will decrease along with Carrier concentration. This change in Carrier concentration is related to changes in oxygen vacancy concentration. The figure of merit obtained in this study means that Ga-doped ZnO films which annealed at $400^{\circ}C$ have the lowest Carrier concentration and Oxygen vacancy, which have the highest optoelectrical performance that it could be used as a transparent electrode.

• 한국결정성장학회지
• /
• 제6권4호
• /
• pp.493-500
• /
• 1996

Al이 2 wt% 포함되어 있는 Zn 금속타겟을 사용하여 반응성 직류 magnetron sputtering법으로 AZO(Aluminum doped zinc oxide) 투명전도막을 제조한 후 열처리함에 따라 변하는 박막의 전기적 광학적 특성을 조사하였다. 전이영역에서 증착된 막들은 비저항이 50 % 정도 감소하여 $1{\times}10^{-3}~3.5{\times}10^{-4}\;{\Omega}cm$로 전기적 특성이 향상되었으며, 높은 산소분압에서 산화물로 증착된 막의 비저항이 증착직후에는 $10^{3}\;{\Omega}cm$였으나 열처리 후에는 $2{\times}10^{-3}\;{\Omega}cm$로 감소하였다. 또 전이영역에서 증착된 막은 증착직후 59.4 %이던 평균투과율이 $400^{\circ}C$, 30분 열처리 후에는 77.4 %까지 향상되었다.

• 센서학회지
• /
• 제14권2호
• /
• pp.63-68
• /
• 2005

The nano-grained Pd or Pt-doped $SnO_{2}$ thin films were deposited on the alumina substrate at ambient temperature or $300^{\circ}C$ by using an R.F. magnetron sputtering system and then annealed at $650^{\cir}C$ for 1 hour or 4 hours in air. The crystallinity and microstructure of the annealed films were analyzed. A grain size of the thin films was 30 nm to 50 nm. As a result of gas sensitivity measurements to an alcohol vapor of $36^{\circ}C$, the 2 wt.% Pt-doped $SnO_{2}$ thin-film sensor deposited at $300^{\circ}C$ and annealed at $650^{\circ}C$ for 4 hours showed the highest sensitivity.

• 한국표면공학회지
• /
• 제29권2호
• /
• pp.93-99
• /
• 1996

In this work BN thin films were deposited on Si substrate by R. F. sputtering method at $200^{\circ}C$ and in Ar + $N_2$ mixed gas atmosphere. In order to investigate the effect of ion bombardment on substrate for c-BN bonding, substrate bias voltage was applied. The optimum substrate bias voltage for c-BN bonding was determined by FTIR analysis on specimens which were deposited with various bias voltages. Then BN thin film was deposited with this optimum condition and its phase, morphology, chemical composition, and refractive index were compared with those of BN film which was deposited without bias voltage. FTIR results showed that BN films deposited with substrate bias voltage were composed of mixed phases of c-BN and h-BN, while those deposited without bias voltage were h-BN only. When pure Ar gas was used for sputtering gas, BN films were delaminated easily from substrate in air, while when 10% $N_2$ gas was added to the sputtering gas, although c-BN specific infrared peak was reduced, delamination did not occur. GXRD and TEM results showed that BN films were amorphous phases regardless of substrate bias voltage, and AES results showed that the chemical compositions of B/N were about 1.7~1.8. The refractive index of BN film deposited with bias voltage was higher than that without bias voltage. The reason is believed to be the existence of c-BN bonding in BN film and the higher density of film that deposited with the substrate bias voltage.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.60-61
• /
• 2007

IAZO (indium aluminium zinc oxide) anode films were co-sputtered on glass substrate using a dual target DC magnetron sputtering system. For preparation of IATO films, at constant DC power of IZO (indium zinc oxide) target of 100 W, the DC power of AZO (Aluminum zinc oxide) target was varied from 0 to 100 W. To analyze electrical and optical properties of IAZO anode, Hall measurement examination and UV/V is spectrometer were performed, respectively. In addition, structure of IAZO anode film was examined by X-ray diffraction (XRD) method. Surface smoothness was investigated by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). From co-sputtered IAZO anode, good conductivity($2.32{\times}10^{-4}{\Omega}.cm$) and high transparency(approximately 80%) in the visible range were obtained even at low temperature deposition. Finally, J-V-L characteristics of phosphorescent OLED with IAZO anode were studied by Keithley 2400 and compared with phosphorescent OLED with conventional ITO anode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.144-145
• /
• 2006

ZnO is a promising material to make high efficiency violet or blue light emitting diodes (LEDs) for its large binding energy (60meV) and big bandgap. But the high quality p-type conduction of ZnO is a dilemma to achieve LEDs with it. In present study, we presented a reliable method to prepare ZnO thin films on (100)silicon substrates by RF magnetron sputtering in the mixture ambient of $N_2$ and $O_2$, accompanying with low pressure annealing in the sputtering chamber in $O_2$ at $600^{\circ}C$ and $800^{\circ}C$ respectively. X-ray diffraction and Hail effect with Van der Paul method were performed to test ZnO films. Seeback effect was also carried out to identify carrier types in ZnO films and showed the N-doped ZnO film annealed at $800^{\circ}C$ had achieved p-type conduction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.451-452
• /
• 2006

We studied the electro-optical characteristic of vertical alignment liquid crystal display(VA-LCD) on the $SiO_x$ thin film deposited $45^{\circ}$ oblique by rf magnetic sputtering system. LC alignment characteristic showed homeotropic alignment, and pretilt angle was about $90^{\circ}$. A uniform liquid crystal alignment effect on the $SiO_x$ thin film was achieved and the electro-optical characteristic of the $SiO_x$ thin film deposited $45^{\circ}$ oblique by rf magnetic sputtering system was excellent.

• 한국진공학회지
• /
• 제12권4호
• /
• pp.269-274
• /
• 2003

The electrical, optical and structural properties of ZnNiO thin _ films deposited on Si substrates using rf-magnetron sputtering method have been investigated before and after the thermal annealing processes. The crystallinity of the ZnNiO thin film become degraded with increasing the Ni contents. This is mainly because the lattice of the thin film was expanded due to the oxygen-deficient conditions. Concerning the electrical properties of the thin film, the carrier concentration increases ($6.81\times10^{14}\textrm{cm}^{-2}$) and Hall mobility decreases (36.3 $\textrm{cm}^2$/Vㆍs) with higher doping concentration of Ni. However, the carrier concentration and Hall mobility became low ($1.10\times10^{14}\textrm{cm}^2$ and high (209.6 $\textrm{cm}^2$/Vㆍs), respectively, after the thermal annealing process at $1000 ^{\circ}C$. We also observed a strong luminescene center peaking at 546 nm in photoluminescence spectra, which was caused by a deep level center in the ZnO band gap with oxygen deficient ZnNiO structure.

• 한국전기전자재료학회논문지
• /
• 제25권12호
• /
• pp.979-983
• /
• 2012

We proposed the ZnO thin film for a SAW filter by PLD and RF sputtering method. ZnO thin films was pre-deposited on a sapphire substrate as a seed layer by PLD method and then deposited on seed layer by RF sputtering. The surface characteristics of ZnO thin film were investigated by XRD, SEM and AFM. The minimum surface roughness was 1.92 nm and FWHM of rocking curve was $0.92^{\circ}$. We demonstrated the SAW filter with bandwidth of approximately 0.97 MHz and the center frequency of 18.72 MHz using the proposed ZnO thin film.