• Textile Coloration and Finishing
• /
• v.9 no.1
• /
• pp.15-22
• /
• 1997

The alkali treated and black dyed PET fabrics were sputter etched under Ar gas atmosphere. The color depth of PET fabrics were increased with sputter etching time only under some limits of discharge power. And above that limits of discharge power the color depth of PET fabrics was decreased by increasing discharge power and treatment time. Minute cracks were made by sputter etching in the whole surface of fabrics to the direction of perpendicular to the longitudinal side of yarns. The fineness and density of minute crack were increased with lowering discharge power. And the size of crack was far smaller than that of microcrater which was obtained by alkali treatment. It is considered that the increase of color depth is related to the minute crack. The water permeation time of sputter etched fabrics was increased with increasing discharge power and treating time. The increase of color depth attained by sputter etching was fully kept through repeated laundering.

• Fashion & Textile Research Journal
• /
• v.3 no.4
• /
• pp.344-350
• /
• 2001

Wool fabrics were treated with dichloro isocyanuric acid (DCCA) and dyed with acid dyes (C.I. Acid Red 18), and then, they were treated by sputter etching. Wool fabrics had been sputtered with aluminium under various conditions such as sputter etching time and discharge power in the presence of argon gas. We compared mechanical properties, colour difference and fastness properties of these samples one another: Mechanical properties and colour difference of sputtered wool fabrics changed by sputter etching time, discharge power and DCCA concentration. Light fastness showed a rising tendency but rubbing fastness showed a downward tendency when sputter etching time was 7 minutes.

• Textile Coloration and Finishing
• /
• v.6 no.3
• /
• pp.44-51
• /
• 1994

Wool and silk fabrics dyed with C.l. Acid Black 155 were subjected to sputter etching and exposed to a low temperature argon plasma. Color depth of shade of the fabrics increased considerably, but sputter etching was more effectively than argon low temperature plasma treatment. And measured for any significant chemical modification by ESCA (XPS). Sputter etching and argon low temperature plasma treatments incorporated oxygen atoms into the surface.

• Journal of the Korean Ceramic Society
• /
• v.34 no.12
• /
• pp.1227-1234
• /
• 1997

ZnO thin films were prepared by rf-magnetron sputter at various conditions. Crystallinity, microstructure, chemical composition, and optical composition, and optical properties of the films were investigated as functions of substrate temperature (R. T.-50$0^{\circ}C$) an sputter gas (O2/Ar=0-50%). ZnO thin films grown at 50$0^{\circ}C$ with sputter gas of pure argon as well as at R. T. with sputter gas of a mixture of argon & oxygen(O2/Ar=2%) exhibit a strong tendency of (002) preferred orientation, compared with a considerable random orientation at the other conditions. The thin films with (002) preferred orientation has a chemical stoichiometry of Zn/O-1.01, a band gap of 3.3eV, and a packing density of 98% respectively.

• Textile Coloration and Finishing
• /
• v.8 no.2
• /
• pp.56-63
• /
• 1996

Low-temperature plasma treatment or sputter etching is of interest as one of the techniques to modify polymer surface. In this study, poly(ethylene terephthalate)(PET), nylon 6 and cotton fabrics dyed three black dyes were subjected to low-temperature argon plasma and also sputter etching. In relation to bathochromic effect, the surface characteristics of the treated fabrics and films were investigated by means of critical surface tension, SEM and ESCA measurement. The depth of shade of fabrics more increased by the sputter etching technique than argon plasma treatment. Many microcraters on the fiber surface formed by the sputter etching resulted in increase of surface area of the fiber and wettability, but the hydrophobic group was increased by the results of ESCA analysis. In particular the change in reflective index of the fibers was much more effective than the chemical composition of the fiber surface on increasing of the depth of shade.

• Textile Coloration and Finishing
• /
• v.9 no.2
• /
• pp.50-56
• /
• 1997

Poly(ethylene terephthalate) (PET) has been etched by sputtering in the presence of argon gas and the resulting surface modifications investigated via weight loss, time of water permeation, half value period, scanning electron microscope(SEM) and color difference measurements. According to increasing sputter etching time, weight loss increased, the time of water permeation and half value period of the sputter etched PET fabrics decreased. Color depth of fabrics increased by increasing sputter etching time. We investigated the fabric surface modification by SEM. Many microcraters on the fabric surface formed by the sputter etching resulted in increase of surface area of the fabric and wettability.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.59-67
• /
• 1998

In this paper, a rigorous three-dimensional Monte Carlo approach to simulate the sputter yield as a function of the incident ion energy and the incident angle as well as the atomic ejection distribution of the target is presented. The sputter yield of the target atom (Cu, Al) has been calculated for the different species of the incident atoms with the incident energy range of 10 eV ~ 100 KeV, which coincides with the previously reported experimental results. According to the simulation results, the calculated sputter yield tends to increase with the amount of the energy of the incident atoms. Our simulation revealed that the maximum sputter yield can be obtained for the incident atom with 10 KeV for the heavy ion, while the maximum sputter yield for the light ion is for the incident atoms with an energy less than 1 KeV. The sputter yield increases with angle of incidence and seems to have the maximum value at 68$^{\circ}$. For angular distributions of the sputtered particle, the atoms in the direction normal to the surface increase with angle of incidence. Furthermore, we has conducted the parallel computation on CRAY T3E supercomputer and built a GUI(Graphic User Interface) system running the sputter simulator.

• Textile Coloration and Finishing
• /
• v.9 no.6
• /
• pp.10-17
• /
• 1997

In order to improve the anti-static property of several hydrophobic fibers by sputter etching, polyester, polypropylene and poly(p-phenylene sulfide) have been etched by sputtering in the presence of argon gas and the resulting anti-static property investigated by half time decay, the time of water permeation, weight loss rate and scanning electron microscope(SEM). The temporary change and durability of anti-static property of samples treated with sputter etching were evaluated. The results were as follows; 1) Half time decay of samples treated with sputter etching were decreased about 18~38%. According to increasing sputter etching time, half time decay is decreased. 2) The wettability and weight loss rate of treated samples were increased remarkably. According to the SEM photographs, many microcraters on the substrate surface by the sputter etching were observed. 3) Although the washing treatment and the time elapsed after treatment are allowed longer, the variation of half time decay hardly can find.

• The Korean Journal of Ceramics
• /
• v.7 no.2
• /
• pp.85-92
• /
• 2001

Thin films of ZnO and Al doped ZnO were prepared by rf magnetron sputter techniques. When the oxygen fraction in Ar-O$_2$ sputter gas was about 2.0%, the films exhibited the composition of Zn:O=1.05:1. The films prepared at 250 W contain larger grains than the films grown at 100 W. However, high deposition rate seems to deteriorates the crystallinity as well as Al-substitution, resulting in lower concentration of mobile electrons. The Al-doped ZnO films which were deposited at $500^{\circ}C$ show resistance of 1$\times$10$^-2$ Wcm; optical band gap of the films ranges from 3.25 to 3.40 eV. These electrical and optical features are related with microstructural as well as crystalline characteristics of the films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.277-283
• /
• 2009

In this paper, aluminum doped zinc oxide (ZnO:Al) thin films on plastic substrate such as poly carbonate (PC), polyethylene terephthalate (PET) were prepared by RF magnetron sputtering method for flexible solar cell applications. Effects of the sputter pressure on the structural, electrical and optical properties were investigated. The crystallinity and the degree of the (002) orientation were deteriorated with increasing the sputter pressure. When the sputter pressure was higher, the conductivity of ZnO:Al films was improved because of the high carrier concentration and the Hall mobility. High quality ZnO:Al films with resistivity as low as $1.9{\times}10^{-3}{\Omega}-cm$ and the optical transmittance over 80 % in the visible region have been obtained on PC substrate at 2 mTorr.