• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.3
• /
• pp.301-310
• /
• 2004

In this paper, a compact dual-mode filter structure without coupling gaps is proposed. The novel design is achieved by embedding a pair of equal crossed slots and spur-lines. Without coupling gaps between feed lines and patch resonator, the new filter can provide low insertion loss. It is found that this design has wide coupling range for dual-mode operation. It means that these characteristics of the proposed filter can reduce uncertainty in fabrication. By using two PIN diodes mounted inside a pair of spur-lines, the proposed structure works as a switchable filter. Also, it has a size reduction of about 34.7 %, compared with conventional dual-mode filters.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1178-1183
• /
• 2004

In this paper, a novel microstrip patch antenna with switchable polarization is proposed. The proposed antenna has a simple structure, consisting of a square radiating patch, a pair of L-type spur-lines, and a microstrip line feed. It can produce either linear polarization or circular polarization by setting the diode on or off From the measured results, low cross polarization levels when operated in the linear polarization, and good axial ratios in the circular state have been observed.

• KCID journal
• /
• v.21 no.1
• /
• pp.118-126
• /
• 2014

In this study, the use of the spur of riverbank technique is being investigated. The spur of the riverbank typically reduces the velocity of flow and protects the embankments by increasing friction along the water and the banks. This also has an effect in the rise of water level upstream. It is also used for the rectification of riverside line and restoration of the waterway through sedimentation near the spur of the riverbank. In this study, physical-scaled experiments are conducted to investigate the process of creating a mild meandering channel using the spur of the riverbank with varying water flows and sedimentation functions. The hydraulics observations are taken with respect to the varying heights and length of the riverbank's spurs and the distance between each spur for the formation of the mild meandering channel. It is observed that for 1.06 times of the meander length, it requires 2 times of the interval with each spur of river width. Similarly, 1.25L times of the meander length, it requires 0.5 times of the interval with each spur of river width. The sand accumulation is induced by the spur of riverbank when the spur of riverbank's heights are more than 40% of water depth and the length of the spur of riverbank needs under than 20% of river width for avoid exaggerated sand accumulation in the center of channel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.702-708
• /
• 2002

In this paper, we design the dual frequency antenna that could easily determine two operation frequencies by its inverted-F antenna structure and spur line length. The spur line is applied to the inverted-F antenna, in order to dual operation characteristics in PCS and cellular frequencies. It has designed by using the IE3D commercial software based on the moment method. As the designed antenna is fabricated and measured, you can see the results such as the return loss, the input impedance, the radiation patterns, and the gain. The size of this antenna is 40 mm$\times$14 mm$\times$9.4 mm, it is compact enough to use as an intenna. Also, This antenna can be used with cellular and PCS phone of domestic market.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.357-364
• /
• 2000

In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear not only in the root, but the tip of tooth and tooth edge.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1090-1099
• /
• 2004

In this paper a novel design of equilateral-triangular microstrip antenna using PIN diode fur switching the resonant frequency is presented and experimentally studied. The proposed antenna has changed the resonant frequency by length of spur-lines on the patch, and PIN diodes are utilized to switch the spur-line on and off. The shape of the spur-line is changed according to the on and off states of PIN diode and the equilateral triangular microstrip antenna has different resonant frequencies in accordance with them. The resonant frequency is 1.22 GHz with off states since the surface currents flow the periphery of T shape spur-lines, while the resonant frequency is 1.82 GHz with on states since the surface currents are little effect with the conventional equilateral triangular microstrip antenna. The radiation pattern of the proposed antenna has a good linear polarization with the cross polarization of -20 dB both with on and off states.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.25-34
• /
• 1999

In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear in the root and the tip of tooth and tooth edge.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.251-257
• /
• 2000

A numerical simulation of the temperature rise for sliding surface in dry contact is based on Jaeger's formula combined with a calculated heat input. A gear tooth temperature analysis was performed. The pressure distribution has the Hertzian pressure distribution on the heat source. The heat partition factor is calculated along line of action. A Temperature distribution of tooth surface is calculated about before and after profile modification. A Temperature of addendum and deddendum in modified gear have reduced.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.223-230
• /
• 2003

Stress patterns are created in the plastic spur gear tooth body by introducing a hole or a steel pin to improve stress distribution. Static analysis using finite element method is carried out to show the effect. The result shows that maximum stress as well as tooth tip displacement is dependent on the size and location of a hole or a steel pin. When a hole located on the tooth center line, the maximum static stress level and the tooth tip deflection is always higher than that of a solid gear. But, a considerable reduction in the maximum stress and tooth tip displacement is achieved by insertion of steel pin.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.928-935
• /
• 2018

In this paper, a compact fully printable bandpass filter is suggested for a low-frequency channel 3.2 GHz ~ 3.7 GHz in the Ultra-Wideband (UWB) communication system. It is featured with a small geometry of $0.5{\lambda}_g/15$ and a low insertion loss despite using FR4 as a cheap substrate of a high dielectric loss. This is made possible by generating zeroth-order-resonance (ZOR) from one cell comprising two series resonances obviously separated from one shunt resonance as a third-order bandpass filter. Especially, the series resonance elements are combined with spur-lines bent by 90 degrees, which makes the port-impedance matched well and eliminates spurious hikes in the stopband, while the overall size remains almost unchanged. The design is carried out by setting up the equivalent circuit and the circuit simulation is checked by the full-wave EM analysis. The structure is manufactured and measured to show that the circuit modeling and EM simulation results agree with the measured data.