• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.10a
• /
• pp.158-162
• /
• 1996

A split shaft device is commonly used to measure the radial force of lip seals. The radial force measured with this device includes some inevitable error. This error is caused by the fact that the split shafts cannot maintain a perfect circle when the interference becomes larger or smaller than some initial interference. In this study, a theoretical model for the calculation of the radial contact force has been carried out, and an explicit equation for the measurement error as a function of the initial interference and the interference to be measured has been obtained. The error when the interference is small is not dependent upon the material properties and the shape of the lip seal, but rather upon the amplitude of the initial interference and the interference to be measured. When the interference is larger or smaller than the initial interference, the measured contact force is always underestimated or overestimated.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1945-1954
• /
• 2017

In recent years, several LCL filter design methods for different converter topologies have been published, many of which use analytical expressions to calculate the ideal converter AC voltage harmonic spectrum. This paper presents the LCL filter design methodology but the focus is on presentation and validation of the non-iterative filter design method for a grid-connected three-phase two-level PWM-VSC. The developed method can be adapted for different converter topologies and PWM algorithms. Furthermore, as a starting point for the design procedure, only the range of PWM carrier frequencies is required instead of an exact value. System nonlinearities, usually omitted from analysis have a significant influence on VSC AC voltage harmonic spectrum. In order to achieve better accuracy of the proposed procedure, the system nonlinear model is incorporated into the method. Optimal filter parameters are determined using the novel cost function based on higher frequency losses of the filter. An example of LCL filter design for a 40 kVA grid-connected PWM-VSC has been presented. Obtained results have been used to construct the corresponding laboratory setup and measurements have been performed to verify the proposed method.

• Journal of the Korean Mathematical Society
• /
• v.38 no.6
• /
• pp.1235-1243
• /
• 2001

We obtain bounds relating to Eulers formula for the case of a function with higher-order convexity properties. These are used to derive estimates of the error involved in the use of the trapezoidal formula for integrating such a function.

• Journal of radiological science and technology
• /
• v.39 no.2
• /
• pp.199-208
• /
• 2016

$^{99}mTc-MAG_3$ Renal scan is a method that acquires dynamic renal scan image by using $^{99}mTc-MAG_3$ and dynamically visualizes process of radioactive agent being absorbed to kidney and excreted continuously. Once the test starts, ratio in both kidneys in 1~2.5 minutes was measured to obtain split renal function and split renal function can be expressed in ratio based on overall renal function. This study is based on compares split renal function obtained from data acquired from posterior detector, which is a conventional renal function test method, with split renal function acquired from the geometric mean of values obtained from anterior and posterior detectors, and studies utility of attenuation compensation depending on difference in geometric mean kidney depth. From July, 2015 to February 2016, 33 patients who undertook $^{99}mTc-MAG_3$ Renal scan(13 male, 20 female, average age of 44.66 with range of 5~70, average height of 160.40cm, average weight of 55.40kg) were selected as subjects. Depth of kidney was shown to be 65.82 mm at average for left and 71.62 mm at average for right. In supine position, 30 out of 33 patients showed higher ratio of deep-situated kidney and lower ratio of shallow-situated kidney. Such result is deemed to be due to correction by attenuation between deep-situated kidney and detector and in case where there is difference between the depth of both kidneys such as, lesions in or around kidney, spine malformation, and ectopic kidney, ratio of deep-situated kidney must be compensated for more accurate calculation of split renal function, when compared to the conventional test method (posterior detector counting).

• Communications of the Korean Mathematical Society
• /
• v.35 no.4
• /
• pp.1171-1184
• /
• 2020

This paper presents several fractional generalizations and extensions of known integral inequalities. To obtain these, an extended generalized Mittag-Leffler function and its fractional integral operator are used.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.168-173
• /
• 2004

This article describes the design of a hydraulic system for a power split type continuously variable transmission (CVT). The CVT considered here, is composed of planetary gears, clutches, and a torque converter which is mainly used for the realization of CVT function. Similar to automatic transmissions, the hydraulic system of CVT is designed for supplying hydraulic flows and pressures to each component of CVT, in order to activate the clutch engagements and torque converter operation, and to cool the drivetrain. By using the mathematical models of drivetrain, a simulation program was developed to investigate the power performance of CVT equipped vehicle and the operating conditions of each component of CVT. And the design parameters of the hydraulic system and clutches were calculated using the operating conditions and power requirements which obtained from the simulation results. Finally the hydraulic circuit design of prototyped valve body is presented based on the numerical results of this analysis.

• 한국ITS학회:학술대회논문집
• /
• 2004.11a
• /
• pp.306-310
• /
• 2004

• The Korean Journal of Applied Statistics
• /
• v.8 no.2
• /
• pp.55-64
• /
• 1995

Three-level Skip-lot sampling plan split by two stages (Split2-SkSP0 is proposed by modifying multi-level skip-lot sampling plan proposed by Choi(1993), which has normal and terrace inspections on the first and the second stages, respectively. The plan is designed to work more higher level inspections when the quality of the submitted products are good, otherwise, return to the normal or the terrace inspection as fast as possible. Also, the formula of the operating characteristic function for the split skip-lot sampling plan is derived using the Markov chain approach. Also, operating characteristic properties of the proposed plans are studied and graphically compared with those of the multi-level skip-lot sampling plans.

• Journal of the Optical Society of Korea
• /
• v.17 no.5
• /
• pp.384-391
• /
• 2013

We propose a split-encryption scheme on converting original images to multiple ciphertexts. This conversion introduces one random phase-only function (POF) to influence phase distribution of the preliminary ciphertexts. In the encryption process, the original image is mathematically split into two POFs. Then, they are modulated on a spatial light modulator one after another. And subsequently two final ciphertexts are generated by utilizing two-step phase-shifting interferometry. In the decryption process, a high-quality reconstructed image with relative error $RE=7.6061{\times}10^{-31}$ can be achieved only when the summation of the two ciphertexts is Fresnel-transformed to the reconstructed plane. During the verification process, any silhouette information was invisible in the two reconstructed images from different single ciphertexts. Both of the two single REs are more than 0.6, which is better than in previous research. Moreover, this proposed scheme works well with gray images.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.6
• /
• pp.1526-1537
• /
• 1998

The split-screen function on the multipoint control unit(MCU) which is usually using processing method based on pixel domain has many problems for manipulating the video signal in real-time. Although the researches and the developements to cope ith such problems are processing, these have too complex architecture to implement and are limited to method for H.261 video signal. In this paper, we propose a new mechanism for split-screen that can actually apply to ISO/IEC MPEG video standard. The new method that is proposed in this paper do the processes in complete compression domain, thus it is suitable for the application of real-time multipoint multimedia communication service. By simple interpreting and manipulating the MPEG video element stream, the split-screen functional module can be implemented easily and the result of the procedures does not accompany image degradation at all. Finally, the complexity of implementation, the aspect for processing delay and the loss of image quality as compared to that resulting in the case of applying the previous split-screen method has been investigated. And it is confirmed that the proposed mechanism has a significant advantage as a split-screen method.