• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.3
• /
• pp.58-69
• /
• 2000

An experimental study was conducted to investigate the influence of the spinning control cylinders which was set on the surface of a fixed circular cylinder in uniform flow, $Re=1.24\times10^4$. The measurements of velocity vectors and pressure distributions are carried out in various spin parameters and angles of spinning control cylinder. The results show that velocity profiles and pressure distributions are different with angles of control cylinder and spin parameters. When the control cylinder angle is $100^{\circ}$, there is more effect in increasing the velocity and the pressure distribution than other cases. In this case, the vortex shedding frequency was increased as increasing spin parameter.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.4
• /
• pp.857-868
• /
• 2001

The aerodynamic forces and wake structures of the non-rotating downstream cylinder which is located behind the spinning upstream cylinder in tandem and staggered arrangement have been investigated by experimental method at Re= $1.32{\times}10^4$. The measurements of wake flow and pressure distributions of downstream cylinder are carried out in various spin parameters by combination of both longitudinal spacing rations L/d=1.5, 3.0, 4.5 and transverse spacing ratios T/d =0.0, -0.5, 0.5. For the present experiment, it has been found that the spin parameter of spinning upstream cylinder affect more easily the downstream cylinder in tandem arrangement than that in staggered arrangement.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.3
• /
• pp.346-359
• /
• 1998

The aerodynamic forces and wake structure of the non-rotating downstream circular cylinder, of which the uniform freestream flow is interfered with another spinning upstream cylinder having the same diameter that is located upstream in a line have been investigated experimentally. When the spin rate of the downstream cylinder defined as the ratio of tangential surface velocity of the spinning cylinder to the freestream velocity increases gradually from zero to 1.4, the change of surface pressure distribution, aerodynamic forces of the non-rotating downstream cylinder were measured in case of several distance ratios of 1.5, 3.0, and 4.5 defined as the ratio of distance between the centers of two cylinders to the diameter. The wake flow patterns behind the cylinder were also investigated in each case. From the present experiments, it has been found that the spin rate significantly influences the aerodynamic forces and near-wake flow phenomena of the downstream cylinder in such a way that the drag increases as the spin rate and distance ratio increase and the wake width increases as the distance ratio increases.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.8 no.4
• /
• pp.55-62
• /
• 1994

This paper studied the streaming electrification with the spinning cylinder system, and compared and analyzed it with the conventional forced flowing system which used a pump or gas for oil flowing As results, in spinning cylinder system, characteristics of the streaming electrification to its rotational speed and oil temperature are same tendency as those of the forced flowing system and it showed the spinning cylinder system is useful to study the streaming electrification. The spinning cylinder system has a simple mechanical structure and needs smaller amount of insulation oil than the conventional forced flowing system and the ef fects of various materials on the streaming electrification could be investigated more conveniently than other methods.

• Fibers and Polymers
• /
• v.7 no.2
• /
• pp.146-157
• /
• 2006

Traditional spinning systems have reached profitability limits in developed countries due to high production costs and low system productivity. Pneumatic spinning is seen as a developing system, because productivity is much higher than conventional systems. This study evaluates one of the main problems to increase productivity in pneumatic spinning, where air mass-flow is dragged by the drafting cylinders. This flow interacts with the incoming fibres deviating them from their expected path. Via laser anemometry, airflow velocity distribution around drafting cylinders has been measured and it has been found that vorticity is created at the cylinder's inlet. Extensive CFD simulation on the air flow dragged by the cylinders has given a clear insight into the vortex created, producing valuable information on how cylinder design affects the vorticity created. Several drafting cylinder designs have been tested without giving any improvement in productivity. However, the use of a drafting cylinder with holes in it produced good results to the problem of air currents, strongly reducing them and therefore allowing a sharp increase in yarn quality, as well as an increase in productivity. An extensive study on vortex kinematics has been undertaken, bringing with it a better understanding of vortex creation, development and breakdown.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1993.10a
• /
• pp.83-88
• /
• 1993

This paper persents the measurement method using a spinning cylinder system for stream-ing electrification of transformer oil. The spinning cylinder system has a simple mechan-ical construction, and requires less oil com-pared to the other methods. Alse, the effects of various admixtures on the static electri-fication and properties of tranformer oil can be easily investigated. Experiments showed that addition of the BTA reduced the streaming electrification and the polarity of static electrification wasconver-ted to negative at 50 ∼ 70[ppm] of BTA

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1615-1618
• /
• 1994

This paper studied the streaming electrification of the U.H.V. transformer with the spinning cylinder system, and compared and analyzed it with the conventional forced flowing system which uses a pump or gas for oil flowing. Also, accumulated surface voltage in its electrified material was measured with the electrostatic voltmeter, and the effect of insulation oil aging was measured. As results, in spinning cylinder system, characteristics of the streaming electrification to its rotational speed and oil temperature are same tendency as those of tile forced flowing system and it showed the spinning cylinder system is useful to study the streaming electrification. And, aging of insulation oil increases the electricity of streaming electrification at initial stage of aging.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.4
• /
• pp.39-49
• /
• 1992

The coherent wake structures behind a spinning cylinder placed in a uniform flow were experimentally investigated by means of phase averaging technique. With a fixed cylinder Reynolds number (Re=6,600), the conditionally sampled velocity vectors were obtained at a section of 3.0 and 10 diameters behind the cylinder for the range of spin parameter S(the ratio of the peripheral velocity to that of the uniform flow) 0 to 2. Spectral analysis and vorticity contours of the velocity data show that up to S=1.2, a Karman vortex street exists within the wake, however, the coherent structures become obscure and their vorticity strength decreases as S increase. Beyond S=1.2, a distinct vortex shedding frequency no longer exists, furthermore coherent structures disappear when S is over 1.6.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.6
• /
• pp.58-65
• /
• 1999

The spinning machine has been developed for a bus and truck wheel disc which is manufactured by spinning process method. This machine has the mechanical structure with bed, 2-column, cross head, 2-vertical slide, 2-horizontal slide with forming roller, clamp slide and main spindle similar to large size vertical lathe. Main spindle attached the mandrel is rotated about 500rpm drived by 280kW power DC motor, and a rotating black material pressed on the mandrel with the clamp slide is spinformed by 2-forming rollers which are attached inner end of the 2-horizontal slides. The 2-vertical and 2-horizontal slides are actuated by the hydraulic cylinder which is controlled by the servo valve individially, and these servo valves are controlled by control signal of the CNC controller which is computed with position signal feedbacked from the encoder sensor. The developed machine can manufacture wheel disc of various section profile without mandrel change because section profile is easily modified using program editing in the CNC controller processor. The wheel disc manufactured by spinning process method has many advantages that the endurance is increased by 2 times and the weight is decreased by 30% compared with a conventional disc.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.6
• /
• pp.88-95
• /
• 2014

Spinning process to inner wall has been applied for reducing the weight of regenerative cooling chamber of liquid propellent rocket engine. The fractures of the blanks of cylinder part and nozzle throat part have been observed during spinning processes. In order to overcome the problem, the mandrel and the blank shape have been modified, and the inner wall was successfully manufactured through the modifications. The manufactured spinning prototype of nozzle throat part was successfully bulged without cracking and necking, and it was confirmed to secure sufficient formability necessary for fabricating thrust chamber.