• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.417-420
• /
• 2000

In order to the torque control the indirect flux control was performed by controlling the ratio of e/f and the q-axis flux was estimated by the slip command and q-axis flux was estimated by the slip command and q-axis current in the rotor circuits. Also the frequency was controlled to keep on the q-axis flux to be zero and the constant torque characteristics could be obtained by generation the preset torque. In the induction motor driven by the boltage source inverter with the constant voltage and frequency the speed variation is expressed as a slip So the speed control can be achieved by slip compensation The slip was calculated with a q-flux current filtered by first-order filter and as the result the error problem which may occur in current detection was eliminated

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.298-303
• /
• 1998

In the speed sensorless control of the induction motor, the machine parameters (especially the secondary resistance R2) have a strong influence to the speed estimation. It is known that the simultaneous estimation of the speed and R2 is impossible in the slip frequency type vector control, because the secondary flux is constant. But the secondary flux is not always constant in the speed transient state. In this paper the R2 estimation in the transient state without adding any additional signal to the stator current is proposed. This algorithm uses the least mean square algorithm and the adaptive algorithm, and it is possible to estimate the R2 exactly. This algorithm is verified by the digital simulations and the experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.970-972
• /
• 2003

This paper presents a new speed sensorless control method of a permanent magnet synchronous motor based on instantaneous reactive power. The proposed algorithm is constructed by instantaneous reactive power in a synchronously rotating reference frame and is not affected by mechanical motor parameters, because mechanical equation is not used. The effectiveness of the proposed system is confirmed by the experimental results.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.974-986
• /
• 2015

A novel inverter fault-tolerant control scheme is proposed to drive brushless DC motor. A fault-tolerant inverter and its three fault-tolerant schemes (i.e., phase A fault-tolerant, phase B fault-tolerant, and phase C fault-tolerant) are analyzed. Eight voltage vectors are summarized and a voltage vector selection table is used in the control scheme to improve the midpoint current of the split capacitors. A stator flux observer is proposed. The observer can improve flux estimation, which does not require any speed adaptation mechanism and is immune to speed estimation error. Global stability of the flux observer is guaranteed by the Lyapunov stability analysis. A novel stator resistance estimator is incorporated into the sensorless drive to compensate for the effects of stator resistance variation. DC offset effects are mitigated by introducing an integral component in the observer gains. Finally, a control system based on the control scheme is established. Simulation and experiment results show that the method is correct and feasible.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권11호
• /
• pp.664-670
• /
• 2004

This paper presents a new velocity estimation strategy of a non-salient permanent magnet synchronous motor (PMSM) drive without high frequency signal injection or special PWM pattern. This approach is based on the d-axis current regulator output voltage of the drive system that has the information of rotor position error. The rotor velocity can be estimated through a rotor position tracking PI controller that controls the position error to zero. For zero and low speed operation, PI controller gains of rotor position tracking controller have a variable structure according to the estimated rotor velocity. In order to boost the bandwidth of PI controller around zero speed, a loop recovery technique is applied to the control system. The proposed method only requires the flux linkage of permanent magnet and is insensitive to the parameter estimation error and variation. The designers can easily determine the possible operating range with a desired bandwidth and perform the vector control even at low speeds. The experimental results show the satisfactory operation of the proposed sensorless algorithm under rated load conditions.

• 한국산학기술학회논문지
• /
• 제19권3호
• /
• pp.104-111
• /
• 2018

본 논문은 무급유식 공기 압축기가 널리 확산됨에 따라 영구자석형 동기 모터를 이용한 고효율 공기 압축기의 센서리스 제어에 관한 논문이다. 공기 압축기는 특성상 위치 센서를 설치하기 어려운 문제를 가지고 있다. 영구자석형 동기모터를 가변속 제어하기 위해서는 회전자의 위치를 파악하기 위한 위치센서가 필수적이다. 따라서 영구자석형 동기모터를 압축기에 활용하기 위해서는 센서리스제어가 필수적이다. 센서리스제어 방식으로 널리 사용되고 있는 역기전력을 통한 위치추정방식은 정지좌표계의 사용으로 인한 위상지연으로 인한 위치오차가 발생하게 되거나, 동기좌표계의 사용으로 인한 과도상태에서 추정역기전력이 오차를 포함하여 발산의 문제 등이 발생되는 문제가 있다. 따라서 본 논문에서는 회전각 추적 관측기를 사용하여 위치와 속도를 추정하고 외란 관측기를 통하여 속도의 리플을 저감시키는 방안을 제시하였다. 프리스케일사의 MPU를 이용하여 실험장치를 구성하고 구현실험을 통하여 제안한 알고리즘의 타당성을 검토하였다. 일정 시점에서 위치오차를 강제로 주더라도 위치보정 값이 위치오차 값을 찾아가며 추정위치가 실제 벡터 위치로 수렴해감을 검증하였다.

• 전력전자학회논문지
• /
• 제5권2호
• /
• pp.149-153
• /
• 2000

최근, 벡터 제어에 있어 무시되어 온 철손의 영향이 여러 논문에서 분석 및 보상되어 왔다. 본 논문은 유도 전동기의 고장자자속 기준제어를 이용한 벡터 제어의 운전성능 향상에 관한 연구로서, 모델링시 철손을 고려하고 이를 제어기에 보상함으로써 동특성을 향상하는데 그 목적이 있다. 이를 위하여 무부하시험을 통한 철손 측정과 새로운 비간섭 제어기가 제안된다. 시뮬레이션 및 실험을 통해 제안된 기법의 타당성을 입증한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1105-1107
• /
• 2000

This paper proposes the new reduced-order extended Luenberger observer and presents the application to sensorless vector control of induction motor. The main features of the proposed observer are discussed and compared with the other observers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 학술대회 논문집 전문대학교육위원
• /
• pp.47-52
• /
• 2001

This paper presents a high-performance control system for Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consist of stator flux observer, rotor position/speed estimator, torque estimator, two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source inverter, and F240/C31DSP controller by using fully integrated control software. The stator flux observer is based on the combined voltage and current model with stator flux feedback adaptive control that inputs are current and voltage sensing of motor terminal with estimated rotor angle for wide speed range. The rotor position is estimated by the observed stator flux-linkage space vector. The estimated rotor speed can be determinated by differentiation of the rotor position used only in the current model part of the flux observer for a low speed operating area. To prove the suggested control algorithm, we have a simulation and testing at actual experimental system. The developed digitally high-performance position sensorless control system are shown a good motion control response characteristic results and high performance features using 1.0Kw RSM.

• 대한기계학회논문집A
• /
• 제28권3호
• /
• pp.238-244
• /
• 2004

To monitor the torque of an induction motor using current, the accurate identification of the motor parameters is very important. In this study, the motor parameters such as rotor resistance, stator and rotor leakage inductance, mutual inductance are estimated for torque monitoring and indirect vector control. Estimated parameters are used to monitor the torque of vector controlled induction motor without any speed measuring sensor. Stator current is measured to estimate the magnetizing current which is used to calculate flux linkage, rotor velocity and motor torque. From the experiments, the proposed method shows a good estimation of the motor parameters and torque under the normal rotational speed.