• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.182-188
• /
• 1994

This expermintal study is intended to investigate he development of flank wear in turning os SUS304 which is used in industrial applications and is acknowledged as a machining difficult material. In cutting process, change of velocity, change of feed, and change of depth of cut were investigated about the effect of flank wear, and slenderness ratio is also investigated. The variations of unit cutting force with the change of rake angle and the change of uncut chip area are observed. The friction angles are calculated for the change friction force and observed. The friction angles are calculated for the change friction force and normal forcd on the different rake angles. From this experimental study, the following results can be said. 1. Under the high cutting speed condition, the flaank wear is affected by the feed and depth of cut, but the influence of feed and depth of cut to the flank wear is reduced when the velocity is low. 2. The smaller slenderness ratio is, the shorter the tool life results in high cutting speed, and the lower cutting speed is, the lower the effect of slenderness ratio to the flank wear is. 3. Using the characteristics of force-RMS, the flank wear of a tool can be detected. There are almost no differences between the RMS characteristics of cutting force and feed force.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.1 s.34
• /
• pp.40-46
• /
• 2006

Efficiency of a centrifugal pump is known to drop rapidly with a decrease of specific speed $n_s$. However, below $n_s=60\;[min^{-1},\;m^3/min,\;m]$, the pump characteristics are not yet clear. Therefore, present study is aimed to investigate the influence of large change of specific speed on the performance of a very low specific speed centrifugal pump. Moreover, influence of impeller configuration on the performance of very low specific speed pump is investigated. The results show that very low specific speed can be accomplished by reducing volute throat sectional area using circular spacer. Influence of the spacer's location and configuration in the discharge passage on the pump performance is very small. Best efficiency of very low specific speed centrifugal pump decreases proportionally to the specific speed but the best efficiency decreases on a large scale in the range of $n_s<40$. Influence of impeller configuration on the pump performance and radial thrust of centrifugal pump are considerably small in the range of extremely low specific speed $(n_s=25)$.

• Journal of Korean Port Research
• /
• v.11 no.2
• /
• pp.305-320
• /
• 1997

The objective of this paper is to analysis & forecast on the change in spatial structures of southeast region by development of the Seoul-Pusan high-speed Rail. To measure the spatial structures, it was used the method of mean center and standard distance among of centrographic measures as analytical tools. The changes of spatial structures patten over time and space in the southeast region were surveyed using population and employment data of 57 zones. And also, to forecast the spatial structures of the southeast region after opening of the Seoul-Pusan high-speed rail, it was supposed three(3) scenarios which designed using influential area with centering around of the proposed high-speed rail stations. Therefore, the results of this research indicate as follows; 1) The spatial structures of population is showed a trend of continual concentration toward Ulsan city area, and also the spatial structures of employment is showed a trend of continual dispersion over time. 2) The forecast of three93) scenarios supposed after opening of the Seoul-Pusan high-speed rail in 2006 show a change of the spatial structures with both population concentration and employment dispersion. In the meantime, the rapid increase of population and wide dispersion of employment is reform with centering around HSR stations which builted in the southeast region after opening of high-speed rail. 3) It shall furnish valuable data to establish the development strategy of urban and local region, and also forecast the change of spatial structures about population and employment in influential area which passed on high-speed rail line & stations by method of mean center and standard distance among of centrographic measures as analytical tools.

• Textile Coloration and Finishing
• /
• v.6 no.4
• /
• pp.34-39
• /
• 1994

For the purpose of obtaining high modulus PET tire cord fiber by high spinning speed, the change of initial modulus and taut tie molecules (T.T.M) fraction with the PET tire cord fibers by different spinning speed is investigated. Initial modulus decreased with increasing spinning speed but increased above spinning speed of 1500m/min. Therefore, high modulus PET tire cord fiber may be obtained above spinning speed of 3500m/min. It was found that the initial modulus of fibers depends on fraction of T.T.M.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.47-50
• /
• 2006

High-speed machining is a very useful tool and one of the most effective rapid manufacturing processes. This study sought to produce various high-speed machining materials with excellent quality and dimensional accuracy. However, high-speed machining is not suitable for microscale thin-walled structures because the structure stiffness lacks the ability to resist the cutting force. This paper proposes a new method that is able to rapidly produce very thin-walled structures. This method consists of high-speed machining followed by filling. A strong work-holding force results from the solidification of the filling materials. Low-melting point metal alloys are used to minimize the thermal effects during phase changes and to hold the arbitrarily shaped thin-walled structures quickly during the high-speed machining. We demonstrate some applications, such as thin-walled cylinders and hemispherical shells, to verify the usefulness of this method and compare the analyzed dimensional accuracy of typical parts of the structures.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.5
• /
• pp.431-437
• /
• 2013

Measured acoustic signal from operating high speed train contains frequency change called doppler shift due to its motion. To avoid this doppler shift wind tunnel test is required. But scaledown of model can cause change of source characteristics. And measurements using some part of train cannot reproduce real flow condition. The best way to recognize real noise source characteristics is measurement from operating high speed train but doppler shift makes it hard. So, we developed simple dedopplerization technique for one microphone and applied to field test data of high speed train. Through this, we could capture real frequency of noise from operating high speed train.

• International Journal of Automotive Technology
• /
• v.7 no.6
• /
• pp.697-702
• /
• 2006

The change in the critical speed due to surface temperature of automotive disk brakes may be analyzed both theoretically as well as experimentally. Juddering of disk brakes is closely related to its critical speed. In analyzing the critical speed, if $\sigma$ is positive, Disk develops TEI(Thermo-Elastic Instability) resulting in juddering in disk brakes. And $\sigma$ is affected not only by the critical speed but also by the initial temperature of disk surface. As the initial temperature of the disk surface rises, the critical speed decreases and juddering is developed more easily. Also, when hot spots are developed by TEI, they show large temperature difference in small local range.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.171-176
• /
• 1997

In this paper, We have analyzed dynamic characteristics of cutting force. Test materials are used martensitic heat resisting steel, STS420J2. The obtained results are as follows: 1. Cutting force is smaller make small feed when feed speed make a change. 2. Principal cutting force is smaller make small cutting speed when feed speed make a change.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.7 no.2
• /
• pp.19-26
• /
• 1970

Three kinds of high speed boat have been tested in the Seoul National University tank. Under the range of speed length ratio 2.5, displacement hulls have shown less resistance value than planing hull, but over the range of 3.0, planing hulls are better. Change of resistance due to the change of displacement is more severe in planing hull.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.226-226
• /
• 2010

Boron Nitride (BN) doped GeSbTe films were grown by the ion beam sputtering deposition (IBSD). The in-situ sheet resistance data and the x-ray diffraction patterns showed the crystallization is suppressed due to the BN incorporation. The phase change speed in BN doped GeSbTe films were investigated using the static tester equipped with nanosecond pulsed laser. The phase change speed for BN doped GST films become faster than the corresponding values for an undoped GST film. The Johnson-Mehl-Avrami(JMA) plot and Avrami coefficient for laser crystallization showed that the change in growth mode during the laser crystallization is a most important factor for the phase change speed in the BN doped GST films. The JMA results and the atomic force microscopy (AFM) images indicate that the origin of the change in the crystalline growth mode is due to an increase in the number of initial nucleation sites which is produced by the incorporated BN. In addition, the retension properties for the laser writing/erasing are remarkably improved in BN doped GeSbTe films owing to the stability of the incorporated BN.