• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.466-469
• /
• 2001

In this paper, closed loop V/f control of induction motor has been implemented by the estimated speed. Closed loop V/f control improve the performance of induction motor drive system at low speed compared to open loop V/f control. However, closed loop V/f control need speed sensor. By using the estimated speed, closed loop V/f control is possible without speed sensor. Rotor speed is calculated from the difference between synchronous frequency and slip angular frequency. 3-phase voltage reference is obtained from synchronous frequency. And the PWM technique using space vector PWM is applied in this scheme. In the space vector PWM, effective time of 3-phase voltage reference is used to simplify the calculation of effective voltage time. This scheme is simple to implement and one chip microprocessor was used in experimental system.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1114-1116
• /
• 2000

A direct model reference adaptive control (DMRAC) is applied to the speed control of brushless do(BLDC) motor. The main objective is to achieve precise speed control in the face of varying motor parameters and load. The control is described as an outer loop speed control and an inner current loop control which has raster dynamics than the speed loop. The adaptive control is applied to the outer speed control loop. DMRAC is compared to an indirect adaptive controller(IMRAC) and a PI controller. Simulation results show that the two adaptive controllers give similar respose and are superior to the PI controller. However, the DMRAC algorithm is simpler to implement.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.226-230
• /
• 2000

In this paper, we implemented the QPSK demodulator with a CPLD chip, and examined the results. DD(Decision Directed)-Gardner algorithm is used for STR loop and Decision-Directed algorithm is used for CPR loop. The speed of the QPSK demodulator implemented in FLEX10K chip can be guaranteed approximately 2[Mbpsl] transmission speed. In practical designed by ASIC, the speed is faster than that of CPLD by 5-6 times.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.466-466
• /
• 2000

This paper presents the sinusoidal current ministep technique to drive stepping motor. The stepping motor is coupling to the increment encoder to detect the position and speed of the stepping motor. The data from the encoder is decoded to sine and cosine signal and fed to the driver system. The driver system has two loops control, the inner loop and the outer loop. The inner loop is used to control the rotating of the stepping motor and the outer is used to control the speed of the motor. The rotating of the stepping motor is controlled with the sinusoidal signal. The test results of the inner loop control can control the revolution of the stepping motor is smooth and continuously with similar to the DC motor. The outer loop uses to control the speed of the stepping motor with control the DC voltages apply to the driver. The DC voltages that apply to the driver is controlled by the AC-DC converter The test results of the outer loop control, it can control the speed of motor which is provide the any load in the design.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1059-1068
• /
• 2016

The current operation method for the AVC (Automatic Vehicle Classification) equipment does not generate vehicle speed, traffic volume and vehicle type information when part of the sensors has failed. Inefficiency of current methods would not use the collected data from the normal sensor. In this study was conducted research on the calculating method at the traffic volume and vehicle speed in the sensor failure AVC equipment. The failure situation of the sensor was classified into 4 types. Calculating the traffic volume and vehicle speed information for each type, and accuracy of these informations were analyzed. Analysis results, traffic volume was possible to calculate a highly accurate value (accuracy: 100%, 98%, 97%). In the case of speed, the accuracy of the calculated speed value reaches a level that can be accepted sufficiently (RMSE value is less than 16.8). So, using the methodology proposed in this study are expected to be able to increase the operational efficiency of the AVC equipment.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.4
• /
• pp.533-538
• /
• 2016

In a power grid that has a high penetration of wind power, the highly-fluctuating output power of wind turbine generators (WTGs) adversely impacts the power quality in terms of the system frequency. This paper proposes a power smoothing scheme of a variable-speed WTG that can smooth its fluctuating output power caused by varying wind speeds, thereby improving system frequency regulation. To achieve this, an additional loop relying on the frequency deviation that operates in association with the maximum power point tracking control loop, is proposed; its control gain is modified with the rotor speed. For a low rotor speed, to ensure the stable operation of a WTG, the gain is set to be proportional to the square of the rotor speed. For a high rotor speed, to improve the power smoothing capability, the control gain is set to be proportional to the cube of the rotor speed. The performance of the proposed scheme is investigated under varying wind speeds for the IEEE 14-bus system using an EMTP-RV simulator. The simulation results indicate that the proposed scheme can mitigate the output power fluctuation of WTGs caused by varying wind speeds by adjusting the control gain depending on the rotor speed, thereby supporting system frequency regulation.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1663-1674
• /
• 2017

This paper deals with the robust speed regulation of a surface-mounted permanent magnet synchronous motor (SPMSM) that is subject to parametric uncertainties and external disturbances. The proposed approach retains a conventional cascade control configuration composed of an outer-loop speed control module and inner-loop current control modules. Baseline proportional-integral (PI) controllers are designed for nominal modular systems without accounting for the uncertainties to set a desired control performance of the closed-loop system. After studied in both frequency and time domains, a reduced-order proportional-integral observer (PIO), as a modular disturbance observer, is incorporated with each control module to maintain the ideal performance of the modules. Theoretical analysis confirms the desired performance recovery of the augmented system with modular PIOs to the nominal system. Comparative computer simulations and experimental results validate the proposed cascade control method for SPMSM speed regulation.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.2
• /
• pp.273-280
• /
• 2012

Most variable speed wind turbines have pitch control mechanisms and one of their objectives is to protect turbines when the wind speed is too high. By adjusting pitch angles of wind turbine, the inlet power and the torque developed by the turbine are regulated. In this paper, the difference between the real wind speed and its rated value is regarded as a disturbance, and a component called disturbance observer (DOB) is added to the pre-designed control loop. The additional DOB based controller estimates the disturbance and generates a compensating signal to suppress the effect of disturbance on the system. As a result, the stability and the performance of the closed loop system guaranteed by an outer-loop controller (designed for a nominal system without taking into account of disturbances) are approximately recovered in the steady state. Simulation results are presented to verify the performance of the proposed control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2016-2021
• /
• 2003

This paper deals with a control technique of eliminating the transient vibration with respect to a waist axis of an articulated robot. This control technique is based on a model-based control in order to establish the damping effect on the driven mechanical part. The control model is composed of reduced-order electrical and mechanical parts related to the velocity control loop. The parameters of the control model can be obtained from design data or experimental data. This model estimates a load speed converted to the motor shaft. The difference between the estimated load speed and the motor speed is calculated dynamically, and it is added to the velocity command to suppress the transient vibration. This control method is applied to an articulated robot regarded as a time-invariant system. The effectiveness of the model-based control integrated into the position control loop is verified by simulations. Simulations show satisfactory control results to reduce the transient vibration at the end-effector.

• Journal of Satellite, Information and Communications
• /
• v.11 no.1
• /
• pp.46-50
• /
• 2016

The adaptive power control of Code Division Multiple Access (CDMA) systems for communications between User Equipments (UEs) with a link-budget based Signal-to-Interference Ratio (SIR) estimate which has distance information is applied to three inner loop power control algorithms. The speed estimation performances of these algorithms with their consecutive Transmit-Power-Control (TPC) ratios are compared to each other, and it is concluded that the speed can be estimated using the TPC ratio information of Consecutive TPC Ratio Step-size Closed Loop Power Control (CS-CLPC) and Fixed Step-size Power Control (FSPC).