• Journal of IKEEE
• /
• v.25 no.3
• /
• pp.467-472
• /
• 2021

Stable operation of semiconductor devices is needed even at high temperatures. Among the structures of semiconductor devices, the area that can cause unstable electrical responses at high temperatures is the contact layer between the metal and the semiconductor. In this study, the effect of annealing conditions included in the process of forming a contact layer of nickel silicide(NiSix) on a p-type SiC layer on the specific contact resistance of the contact layer and the total resistance between the metal and the semiconductor was investigated. To this end, a series of electrodes for TLM (transfer length method) measurements were patterned on the 4 inch p-type SiC layer under conditions of changing annealing temperature of 1700 and 1800 ℃ and annealing time of 30 and 60 minutes. As a result, it was confirmed that the annealing conditions affect the resistance of the contact layer and the electrical stability of the device.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.292-292
• /
• 2014

Wide band gap semiconductors, such as III-nitrides (GaN, AlN, InN, and their alloys), SiC, and diamond are expected to play an important role in the next-generation electronic devices. Specifically, GaN-based high electron mobility transistors (HEMTs) have been targeted for high power, high frequency, and high temperature operation electronic devices for mobile communication systems, radars, and power electronics because of their high critical breakdown fields, high saturation velocities, and high thermal conductivities. For the stable operation, high power, high frequency and high breakdown voltage and high current density, the fabrication methods have to be optimized with considerable attention. In this study, low ohmic contact resistance and smooth surface morphology to AlGaN/GaN on 2 inch c-plane sapphire substrate has been obtained with stepwise annealing at three different temperatures. The metallization was performed under deposition of a composite metal layer of Ti/Al/Ni/Au with thickness. After multi-layer metal stacking, rapid thermal annealing (RTA) process was applied with stepwise annealing temperature program profile. As results, we obtained a minimum specific contact resistance of $1.6{\times}10^{-7}{\Omega}cm2$.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.29-33
• /
• 2003

Material and electrical properties of copper-based ohmic contacts on n-type 4H-SiC were investigated for the effects of the post-annealing and the metal covering conditions. The ohmic contacts were prepared by sequential sputtering of Cu and Si layers on SiC substrate. The post-annealing treatment was performed using RTP (rapid thermal process) in vacuum and reduction ambient. The specific contact resistivity ($p_{c}$), sheet resistance ($R_{s}$), contact resistance ($R_{c}$), transfer length ($L_{T}$), were calculated from resistance (RT) versus contact spacing (d) measurements obtained from TLM (transmission line method) structure. The best result of the specific contact resistivity was obtained for the sample annealed in the reduction ambient as $p_{c}= 1.0 \times 10^{-6}\Omega \textrm{cm}^2$. The material properties of the copper contacts were also examined by using XRD. The results showed that copper silicide was formed on SiC as a result of intermixing Cu and Si layer.

• Journal of the Korean Vacuum Society
• /
• v.11 no.1
• /
• pp.35-42
• /
• 2002

We fabricate thermally stable and low resistance Ru ohmic contacts to $n-ZnO:Al(3\times10^{18}\textrm{cm}^{-3})$, grown by specially designed dual target sputtering system. It is shown that the as-deposited Ru contact produces a specific contact resistance of $2.1{\times}10^{-3}{\Omega}\textrm{cm}^2$. Annealing of the Ru contacts leads to the improvement of current-voltage characteristics. For example, annealing of the contact at $700^{\circ}C$ for 1 min produces a contact resistance of $3.2{\times}10^{-5}}{\Omega}\textrm{cm}^2$. furthermore, the metallisation scheme is found to be thermally stable: the surface of the contact is fairly smooth with a rms roughness of 1.4 nm upon annealing at $700^{\circ}C$. These results strongly indicate that the Ru contact represents a suitable metallisation scheme for fabrication of high-performance ZnO-based optical devices and high-temperature devices. In addition, possible mechanisms are suggested to describe the annealing temperature dependence of the specific contact resistance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.25-26
• /
• 2008

Electrical properties of Pt/Ti/Au/Pt contacts to n-GaAs were characterized as the V/III ratio of GaAs grown by metalorganic chemical vapor deposition were 25, 50, and 100, respectively. The samples have been annealed during 30sec at 350 and $450^{\circ}C$ in rapid thermal annealing, and those specific contact resistance investigated by using transmission line method. According to experimental results, the specific contact resistance between p-metal and GaAs was decreased as the V/III ratio was lower. These results indicate that Si doping concentration of GaAs increased as the vacancy of V-series of GaAs was high.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.834-837
• /
• 2003

In this study, Ohmic contacts make on 3C-SiC using TiN. Ohmic contact resistivity of TiN/3C-SiC was evaluated. Specific contact resistance was calculated by Circular-TLM(transmission line model) method and physics properties were measured using XRD, SEM, respectively. TiN contact is stable at high temperatures and a good diffusion barrier material. The TiN/3C-SiC contacts are thermally stable to annealing temperatures up to $1000^{\circ}C$. The TiN thin-film depostied on 3C-SiC substraes have good electrical properties. Therefore, the TiN/3C-SiC contact can be usefully applied for high-temperature MEMS applications over $500^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Tribology and Lubricants
• /
• v.36 no.5
• /
• pp.290-296
• /
• 2020

When two layers of carbon nanotube (CNT) arrays are loaded to mate, the free ends of individual CNTs come into contact at the interface of the two layers. This leads to a higher contact resistance due to a smaller contact region. However, when the free CNT ends of one array penetrate into the mating array, the contact region increases, effectively lowering the contact resistance. To explore the penetration of mating CNTs, we perform molecular dynamic simulations of a simple unit cell model, incorporating four CNTs in the lower array layer coupled with a single moving CNT on the upper layer. The interaction with neighboring CNTs is modelled by long-range carbon bond order potential (LCBOP I). The model structure is optimized by energy minimization through the conjugate gradient method. A NVT ensemble is used for maintain a room temperature during simulation. The time integration is performed through the velocity-Verlet algorithm. A significant vibrational motion of CNTs is captured when penetration is not available, resulting in a specific vibration mode with a high frequency. Due to this vibrational behavior, the random behaviors of CNT motion for predicting the penetration are confirmed under the specific gap distances between CNTs. Thus, the probability of penetration is examined according to the gap distance between CNTs in the lower array and the aspect ratio of CNTs. The penetration is significantly affected by the vibration mode due to the van der Waals forces between CNTs.

• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.456-461
• /
• 2010

We investigated the In-based ohmic contacts on Nitrogen-face (N-face) n-type GaN, as well as Ga-face n-type GaN, for InGaN-based vertical Light Emitting Diodes (LEDs). For this purpose, we fabricated Circular Transfer Length Method (CTLM) patterns on the N-face n-GaN that were prepared by using a laser-lift off method, as well as on the Ga-face n-GaN that were prepared by using a dry etching method. Then, In/transparent conducting oxide (TCO) and In/TiW schemes were deposited on the CTLM in order for low resistance ohmic contacts to form. The In/TCO scheme on the Ga-face n-GaN showed high specific contact resistance, while the minimum specific contact resistance was only 3${\times}$10$^{-2}$ $\Omega$-cm$^{2}$ after annealing at 300${^{\circ}C}$, which can be attributed to the high sheet resistance of the TCO layer. In contrast, the In/TiW scheme on the Ga-face n-GaN produced low specific contact resistance of 2.1${\times}$10$^{5}$ $\Omega$-cm$^{2}$ after annealing at 500${^{\circ}C}$ for 1 min. In addition, the In/TiW scheme on the N-face n-GaN also resulted in a low specific contact resistance of 2.2${\times}$10$^{-4}$ $\Omega$-cm$^{2}$ after annealing at 300${^{\circ}C}$. These results suggest that both the Ga-face n-GaN and N-face n-GaN.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.10
• /
• pp.87-93
• /
• 1994

Ohmic contacts between Au and p-HgHg_{0.7}Cd_{0.3}Te$ with low specific contact resistance have been obtained. The contact region of the wafer is first pre-heated for 5 seconds in a rapid thermal processing equipment. The temperature reaches a maximum value of about 200$^{\circ}C$ at the end of the 5 seconds. Next, a thin Au film is formed on the contact region by immersing the sample in AuCl$_{3}$ solution. the sample is then post-annealed in the same condition as the pre-heating after Pb/In pad metals are deposited on the electroless Au contacts. The specific contact resistance measured by transmission line model is 5${\times}10^{-3}{\Omega}cm^{2}$ at 80K. RBS and differential Hall measurement data suggest that the above low resistance ohmic contact is ascribed to surface traps and increased gold diffusion rate.