• Journal of the Korean institute of surface engineering
• /
• v.24 no.2
• /
• pp.103-113
• /
• 1991

Electroless Ni-Cu-P alloy plating of Al base hard disk was performed to investigate some properties according to the change of composition. It was found that the composition of Ni and Cu in deposits changed linearly with increasing the mole ratio of NiSO4.6H2O/CuSO4.5H2O. The increase in hardness by heat - treatment was confirmed to be associated with small size grained crystallization of the amorphous deposits. Acid resistance of all deposits layer. which had been heated up to 30$0^{\circ}C$, was found to be exellent when immersed in 1N-H2SO4 solution, and it showed more superior acid resistance with decreasing Cu content and with increasing P. The resistivity of the deposits heat treated became smaller at temperature more than 50$0^{\circ}C$, and it became largerly with increasing P content. Cu 44.1wt% alloy(C bath) showed the most superior non-magnetically stable characteristics after heat treatment. It was superiorly with higher temperature and with decreasing P content.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.281-284
• /
• 2003

The microstructural changes of Al-Zn-Mg-Cu alloy containing Sc during hot extrusion and post heat treatment is investigated. Two kinds of Al-Sc alloys with different alloying elements (B1, B2) are hot extruded to make I-shape bars at 380$^{\circ}C$, then the bars are solution treated at 480$^{\circ}C$ for 2hrs followed by artificial aging at 120$^{\circ}C$ for 24hrs. The interior microstructure of as extruded bar consists of elongated grains, however, fine equiaxed grains are mainly observed around surface. The microstructural gradient suggests that different restoration process can proceed during the hot extrusion. For B1 and B2, different grain growth behaviors are found around the surface during the post heat treatment. Rapid grain growth behavior around the surface is discussed related with the crystallographic orientation of the grain.

• Textile Coloration and Finishing
• /
• v.14 no.6
• /
• pp.328-334
• /
• 2002

Nylon 6 staple ultramicrofiber(UMF, 0.074) and regular staple fiber (Regular, 2.0d) were annealed at In, 130, 160 and $180^\circ{C}$ under tension free for 10 min and U min. The treated fibers were dyed with Acid Red 18 and Blue n3. They were adjusted at PH 5.0 of dye bath in buffer solution of $CH_3COOH/CH_3/COONa(0.1mo1/1)$. Liquor ratio was kept at 1000:1. Dyeing rate of UMF annealed at $100^\circ{C}$ was decreased, but was increased for regular nylon. Also dye equilibrium of UMF at $100^\circ{C}$ was increased for Acid Red 18, but was decreased for Acid Blue 83. The intensities of X-ray diffraction peaks of UMF increased with increasing annealing temperature. Also the crystallinity of heat-sotted fibers by DSC thermogram was well agreed with the tendency of density Amino end group, moisture regain and water absorbency were decreased with increasing annealing temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.217-227
• /
• 2004

The bowl in a ship purifier suffers from high stress and high temperature in a detrimental heavy fuel oil environment. Duplex stainless steel(DSS) is a primary material to withstand this harsh condition. Newly-manufactured STS 329 grade DSS has been evaluated by various mechanical and electrochemical test methods. Eight heat treatment(HT) conditions with different temperature and time were applied to the DSS samples to improve corrosion resistance. Microstructure and polarization test results concluded the optimum HT condition was $1.090^{\circ}C$-60 minutes. Confirmation experiments for applying to a real bowl including stress corrosion cracking test exhibited the reproducibility of the optimum HT condition.

• Journal of Biomedical Engineering Research
• /
• v.11 no.2
• /
• pp.295-304
• /
• 1990

In order to use for artificial dental tooth (dental crowens) , new glass-ceramics material has been studied. Its basic composition and the condition of heat treatment for crystalization, mechanical and chemical properties were investigated. Adding of the LAS system composition in the basic glass, time and temperature for crystalization were shortened. Fracture toughness (kic)of samples heat treated at 90$0^{\circ}C$ for 2 hours is 2.5-2.6MN/m3/2, the optimum condition of heat treatment for artificial tooth is A and B samples heating to 75$0^{\circ}C$ for 2 hours, raising to 90$0^{\circ}C$ and maintaining at 90$0^{\circ}C$ for 2 hours and C sample heating to 75$0^{\circ}C$ maintaining at 75$0^{\circ}C$ for 2 hours. In acid and'alkali solution, chemical durability is excellent.

• Food Science and Biotechnology
• /
• v.15 no.3
• /
• pp.441-446
• /
• 2006

The biological effects of heating and chemical treatment on castor meal were investigated in order to develop a procedure to inactivate its antigenic activity in a way that is suitable for industrial applications. A 1% solution of purified castor bean allergen (CB-1A) was heat-treated with or without exposure to NaOH and NaOCI (250 ppm each). CB-1A exhibited extreme stability when heat-treated alone. In the presence of NaOH and NaOCl, CB-1A showed a drastic decrease in antigenic activity as the temperature surpassed the critical level of $70^{\circ}C$. The gradual disappearance of disc gel electrophoresis bands presumably responsible for the allergenicity of CB-1A, along with the significant losses of the amino acids phenylalanine, methionine, arginine, histidine, and cysteine correlated with the loss of CB-1A activity. CB-1A showed a single symmetrical band in SDS acrylamide gel electrophoresis with an estimated molecular weight of 6,000 daltons. The chemical and heat treatments reduced the disulfide bond content of CB-1A by 9.1% with a coincident increase in sulfhydryl bonds.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.7
• /
• pp.717-722
• /
• 2011

The purpose of this study is to predict the residual stress in Al6061 during T6 heat treatment. In this study, the variable residual stress in case of the solid solution($530^{\circ}C$, 2h) and artificial ageing($175^{\circ}C$, 9h) of Al6061 subjected to T6 heat treatment is determined at different ageing times. A heat treatment experiment is conducted to determine the heat transfer coefficient, on the basis of which the residual stress during the T6 heat treatment is predicted. In order to take into account the relaxation of residual stress during artificial ageing, a Zener-Wert-Avrami function is used and elasto-plastic nonlinear analysis is conducted through FE-simulation. Further, the residual stress is measured by using the X-ray diffraction(XRD) method, and the result is compared with the result from the FE-simulation. It is found that the residual stress predicted form the FE-simulation is in good agreement with the residual stress measured by using the XRD method.

• Membrane and Water Treatment
• /
• v.8 no.6
• /
• pp.529-541
• /
• 2017

A multi-effect air gap membrane distillation (ME-AGMD) module for pesticide wastewater treatment is studied with internal heat recovery, sensible heat of brine recovery, number of stages and the use of fresh feed as cooling water in a single module is implemented in this study. A flat sheet polytetrafluroethylene (PTFE) membrane was used in the 4-stage ME-AGMD module. The maximum value of permeate flux could reach $38.62L/m^2h$ at feed -coolant water temperature difference about $52^{\circ}C$. The performance parameter of the module like, specific energy consumption and gain output ratio (GOR) was investigated for the module with and without heat recovery. Also, the module performance was characterized with respect to the separation efficiency of several important water quality parameters. The removal efficiency of the module was found to be >98.8% irrespective water quality parameters. During the experiment the membrane fouling was caused due to the deposition of the salt/crystal on the membrane surface. The membrane fouling was controlled by membrane module washing cycle 9 h and also by acidification of the feed water (pH=4) using 0.1M HCl solution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.125-126
• /
• 2006

The characteristics of the tool system give many effects into the costs and qualities for the finished components. Therefore, a tool life is one of the important issues on cold forging industry. However, since variables related with tool life are many complicated, the studies for solution should be investigated by the systematic research approach. In this study, heat-treatment of tool material is investigated to improve the tool life. Deep cryogenic treatment of tool steel is very efficient to improve the wear resistance due to the fine carbide. And, it is investigated that the shape and dimension of tool give effect into both tool life and quality of forged product.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.4
• /
• pp.196-199
• /
• 2000

Electroless plating is the desirable surface treatment method which is being widely used to all kinds of material such as requiring corrosion resistance, wear resistance and conductivity, especially plating of nonconductive material. Electroless nickel deposit has particular characteristics including non-magnetic property, amorphous structure, wear resistance, corrosion protection and thermal stability. In this study, electroless nickel plating was studied with an change in hardness and corrosion resistance of electroless nickel-phosphorus deposit depending on heat treatment. The highest hardness value was obtained by heat treatment at $500^{\circ}C$ Corrosion resistance of deposit, which had been heated at $300^{\circ}C$, was excellent when it was immersed in 1M $H_2SO_4$ solution for 60 hrs.