• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.32 no.1
• /
• pp.59-74
• /
• 2012

Buffer solubility and protein fractionation were evaluated from the hays (timothy, alfalfa and klein) and straws (tall fescue and rice), and $In$ $vitro$ trial was conducted to examine the effect of buffer extraction on fermentation characteristics, degradability and gas ($CO_2$ and $CH_4$) production. Buffer soluble protein (SP) content and A fraction in total protein were highest in alfalfa hay as 61% and 41.77%, respectively while lowest in rice straw (42.8% and 19.78%, respectively). No difference was observed in B1 fraction among forages but B2 fraction was slightly increased in klein hay (12.34%) and tall fescue straw (10.05%) compared with other forages (6.34~8.85%). B3 fraction of tall fescue was highest as 38.49% without difference among other forages while C fraction was highest in rice straw. pH in incubation solution was higher in all forages after extraction than before extraction at 3h (P<0.01) and 6h (P<0.05), and pH from hays of timothy and alfalfa was higher than the other forages at 6h (P<0.05) and 12h (P<0.001). Regardless of extraction, ammonia-N concentration from alfalfa hay was increased at all incubation times and extraction effect was appeared only at 3h incubation time (P<0.01). Total VFA concentration from alfalfa hay was highest up to 24h incubation while those from tall fescue straw and rice straw were lowest. Buffer extraction decreased (P<0.01~P<0.001) the total VFA concentration. Acetic acid proportion was increased (P<0.001) before extraction of forages but no difference was found between forages. Propionic acid($C_3$) proportion was also increased(P<0.001) before extraction in all forages than in straws at 3h, 24h and 48h incubations, and $C_3$ from hays were mostly higher (P<0.05) than from straws. Butyric acid proportion, however, was not affected by extraction at most incubation times. Parameter 'a' regarding to the dry matter (DM) degradation was increase (P<0.001) in all forages before extraction, and was decreased (P<0.05) in tall fescue straw and rice straw compared with hays. Parameter 'b' was also increased (P<0.001) before extraction but no difference was found between forages. Effective degradability of DM (EDDM) was higher (P<0.001) before extraction in most forages except for rice straw. Buffer extraction decreased (P<0.05) all parameters (a, b, and c) regrading to the crude protein (CP) degradation but no difference was found between forages. Effective degradation of CP (EDCP) was lower (P<0.05) in straws than in hays. Parameters 'a' and 'b' regarding to the NDF degradation (P<0.01) and effective degradability of NDF (EDNDF, P<0.001) were also higher in forages before extraction than after extraction but no difference was found between forages. Buffer extraction reduced (P<0.05~P<0.001) $CO_2$ production from all the forages uo to 24h incubation and its production was greater (P<0.05~P<0.01) from hays than straws. Methane ($CH_4$) production was also greater (P<0.01~P<0.001) in all forages at all incubation times, and its production was greater (P<0.05) from hays than from straws at most incubation times. Based on the results of the current study, it can be concluded that buffer solubility and CP fractionation might be closely related with $In$ $vitro$ VFA concentration, degradability and gas ($CO_2$ and $CH_4$) production. Thus, measurement of buffer solubility and protein fractionation of forages might be useful to improve TMR availability in the ruminants.

• Korean Journal of Food Science and Technology
• /
• v.23 no.2
• /
• pp.235-240
• /
• 1991

Starch phosphates were prepared from the corn starch mixed with 2% sodium tripolyphosphate by twin-screw extruder with a feed rate of 20 kg/hr and an extrusion temperature of $130^{\circ}C$, and the effects of extrusion variables on the physicochemical properties (target parameters) of starch phosphates were investigated. Interrelations of system parameters (specific mechanical energy and extrudate moisture) and rheological properities of starch was analyzed by using the response surface analysis. Degree of substitution (DS) was increased with increasing the feed moisture, and showed the maximum value at the screw of near 250 rpm, Degree of gelatinization was proportionally increased with increasing the screw speed and decreasing the feed moisture. Apparent viscosity of the paste was increased with increasing the feed moisture, but it was not significantly affected by the screw speed. It was found by scanning electron microscopy that the starch microgranules were much more degradaded, and as consequent result, the intrinsic viscosity was decreased, whereas, water solubility index was increased. The rate of retrogradation of the gels was retarded with increasing DS and decreasing viscosity.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.3
• /
• pp.161-170
• /
• 2012

To provide domestic values of input parameters in a safety assessment of radioactive waste disposal under domestic deep underground environments, various kinds of experiments have been carried out under KURT (KAERI Underground Research Tunnel) conditions. The input parameters were classified, and some of them were selected for this study by the criteria of importance. The domestic experimental data under KURT environments were given top priority in the data review process. Foreign data under similar conditions to KURT were also gathered. The collected data were arranged and the statistical calculations were processed. The properties and distribution of the data were explained and compared to foreign values in view of their validity. The following parameters were analysed: failure time and early time failure rate of a container, solubility of nuclides, porosity and density of the buffer, and distribution coefficients of nuclides in the geomedia, hydraulic conductivity, diffusion depth of nuclides, groundwater flow rate, fracture aperture, length of internal fracture, and width of faulted rock mass in the host rock.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.9
• /
• pp.1462-1466
• /
• 2014

In this study, an attempt was made to produce oat protein concentrates from defatted oat groat by alkali extraction. Independent variables formulated by D-optimal design were NaOH concentration (X1, 0.005~0.06 N) for extraction and precipitation pH (X2, pH 4.0~6.0), and the dependent variable was extraction yield (Y1, %). Experimental results were analyzed by response surface methodology to determine optimized extraction conditions. Extraction yield increased both with an increase in NaOH concentration of the extraction solution and when approaching a precipitation pH of 4.9, and NaOH concentrations were a major influencing parameter. Solubility of oat protein concentrates showed a minimum value (i.e., 0.1%) at pH 5 and increased substantially at pH values in the range of ${\leq}$ pH 3 or ${\geq}$ pH 7, reaching a maximum value at pH 11 (i.e., 76%). Regression equation coincided well with the results of the experiment. Optimized extraction conditions to maximize extraction yield were 0.06 N NaOH (X1) for extraction and pH 4.7 (X2) for precipitation.

• Archives of Pharmacal Research
• /
• v.28 no.1
• /
• pp.120-126
• /
• 2005

The objective of this study was to investigate the effects of sodium lauryl sulfate upon the saturation solubility of carbamazepine, its dissolution kinetics, and $T_{50\%}$ defined as the time required for dissolving $50\%$ of carbamazepine. Water, 0.1N-HCI, and phosphate buffers at pH 4.0 and 6.8 containing 0.1, 0.5, 1, and $2\%$ sodium lauryl sulfate were used as dissolution media. The dissolution study was conducted by using the USP dissolution apparatus II with an agitation rate of 75 rpm. Samples of the dissolution media were taken in 7, 15, 30, 45, 60, 75, and 90 min, and the amounts of carbamazepine were determined spectrophotometrically at 285 nm. All dissolution data were fitted well into a four-parameter exponential equation: $Q\;=\;a(1\;-\;e^{-bxt})\;+\;c(1\;-\;e^{-dxt})$. In this equation Q represented $\%$ carbamazepine dissolved at a time t, and a, b, c, and d were constants. This equation led to the calculation of dissolution rates at various time points and $T_{50\%}$. It was found that the dissolution rate of carbamazepine was directly proportional to the aqueous concentration of sodium lauryl sulfate. In addition, under our experimental conditions $T_{50%}$ values ranged from 37.8 to 4.9 min. It was interesting to note that $T_{50\%}$ declined rapidly as the surfactant concentration increased from 0.1 to $0.5\%$, whereas it declined more slowly at concentrations greater than $1\%$. These results clearly demonstrated that the dissolution rate of carbamazepine and duration of its dissolution test could be tailored by optimizing the amount of sodium lauryl sulfate in a dissolution medium.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.252-261
• /
• 1997

The effect of solvent on the dispersion stability of $CaCO_3$ pigment in various solvents and resin solutions has been studied using Dynometer. Dispersion stability can be estimated in a relatively short time by means of Dynometer and the solubility parameter, ${\delta}$, of $CaCO_3$ determined from dispersion stability was 11.62(${\delta}_d=8.04$, ${\delta}_p=5.05$, ${\delta}_h=6.70$). The solvent showing weaker interaction with pigment increased the adsorption of resin on to the pigment, resulting in higher dispersion stability in resin solution. It was found that the rheological properties and dispersion stability of pigmented resin solution were depending strongly on the solvent added in small amount in the formulation.

• Clean Technology
• /
• v.13 no.3
• /
• pp.208-214
• /
• 2007

Environmentally-friendly acrylic resin particles having the diameter between $0.1\;and\;1\;{\mu}m$ were prepared using non-aqueous dispersion (NAD) polymerization technique. The first step is to prepare the stabilizer and the next step is the NAD polymerization by dropping an acrylic monomer to stabilizer dispersed in organic media. To obtain a NAD resin with proper level of viscosity, it fumed out that stabilizers having sufficient viscosity such as 1000 cP need to be used, for which the stepwise feeding of monomer and initiator was necessary. It was necessary to put proper amount of stabilizer, but no more increase in viscosity was observed when more than that amount of stabilizer was added. Choice of proper monomers considering solubility parameter was essential to avoid the bimodal particle size distribution in the NAD resin product.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.239-244
• /
• 2009

In order to alleviate the cyto-toxicity and improve the poor water solubility of 7-hydroxy-3-methoxycadalene, it was substituted with glucose, a strong hydrophilic and non cyto-toxiccompound, in the C-7 position. The yield of final product was ca. 55.4%. The $IC_{50}$ values of 7-O-${\beta}$-D-glucopyranosyl-3-methoxycadalene against normal lung cell (WI-38 cell line) and human lung cancer cell (A-549 cell line), which is a parameter for determination of cell viability, were measured to $298.2{\mu}m$ and $88.6{\mu}m$, respectively. This result indicates that the pharmaceutical efficiency of the cadalene-glucose derivative targeted to lung cancer cell could be improved more than three times compared to the non derivatized cadalene. In addition, glycosylation of 7-hydroxy-3-methoxycadalene turned its hydrophobic property to more soluble in water.

• International Journal of Oral Biology
• /
• v.42 no.2
• /
• pp.63-70
• /
• 2017

Selecting an appropriate antigen with optimal immunogenicity and physicochemical properties is a pivotal factor to develop a protein based subunit vaccine. Despite rapid progress in modern molecular cloning and recombinant protein technology, there remains a huge challenge for purifying and using protein antigens rich in hydrophobic domains, such as membrane associated proteins. To overcome current limitations using hydrophobic proteins as vaccine antigens, we adopted in silico analyses which included bioinformatic prediction and sequence-based protein 3D structure modeling, to develop a novel periodontitis subunit vaccine against the outer membrane protein FomA of Fusobacterium nucleatum. To generate an optimal antigen candidate, we predicted hydrophilicity and B cell epitope parameter by querying to web-based databases, and designed a truncated FomA (tFomA) candidate with better solubility and preserved B cell epitopes. The truncated recombinant protein was engineered to expose epitopes on the surface through simulating amino acid sequence-based 3D folding in aqueous environment. The recombinant tFomA was further expressed and purified, and its immunological properties were evaluated. In the mice intranasal vaccination study, tFomA significantly induced antigen-specific IgG and sIgA responses in both systemic and oral-mucosal compartments, respectively. Our results testify that intelligent in silico designing of antigens provide amenable vaccine epitopes from hard-to-manufacture hydrophobic domain rich microbial antigens.