• Journal of the Korean Ceramic Society
• /
• v.35 no.7
• /
• pp.721-725
• /
• 1998

In this study solid-phase sintered silicon caribide samples composed of SiC powder having boron and car-bon black as additives were prepared by pressureless sintering at $1950^{\circ}C$. The bending strength the frac-ture toughness and the specific werar rate of the samples were examined and the micro structures of the broken and the worn surface were observed by SEM to understand the relationship between the tri-bological charcteristics and the micro structure. Additionally the relationship between the micro struc-tures and the tribological characteristics of the samples for the frictional opponents SiC and $Al_{2}O_{3}$ pins were investigated Conclusions are as follows ; 1. The specific were rate of the samples for the SiC pin was larger than that for the $Al_{2}O_{3}$ pin. HOwever the specific wear rate for the $Al_{2}O_{3}$ pin was increased about 6,45 times as that for the SiC pin under the load increasing. 2. The specific wear rate of the SiC pin was larger than that of the $Al_{2}O_{3}$ pin. owever the specific wear rate of the $Al_{2}O_{3}$ pin was increased about 4 times as that of the SiC pin under the load increasing 3. The micro stucture of the worn surface showed a flat face without cracks in the case that the frictional opponents has the low friction coefficient but in the case of without cracks in the case that the frictional opponents has the low friction coefficient but in the case of the high friction coefficient the micro structure of the worn surface showed an uneven face having spread-ed cracks. 4. The tribological characteristics of thesolid-phase sintered SiC samples was similar to that of li-quid-phase sintered ones when the pin having the high friction coefficient was used.

• Fire Science and Engineering
• /
• v.34 no.1
• /
• pp.47-54
• /
• 2020

This paper proposes a solution to the problems of constructing and installing sway braces for existing standpipes in narrow spaces and pits. The study develops a floor-fixed sway brace for a narrow space that can support the ground area under horizontal seismic loads (X-axis, Y-axis) as well as vertical seismic loads (Z-axis). The results of structural analysis using SolidWorks simulation showed that the eccentric load was generated in the first design according to the anchored position along the vertical direction, and the problem of exceeding the allowable stress of the material along the horizontal and vertical directions. In the second design model, deformation caused by the eccentric load along the vertical direction, similar to the first design model, did not occur. The maximum strain rate was 0.17%, which is approximately 12.84% less than the first design model (Maximum strain rate of 13.01%). It was confirmed that the structural stability and durability improved. Compressive and tensile load testing of the prototypes showed that all of them meet the performance criteria of the standard.

• Journal of Energy Engineering
• /
• v.23 no.4
• /
• pp.207-214
• /
• 2014

With the depletion of high grade coal, it is indispensable to be used co-combustion of low rank coal with bituminous coal in pulverized coal-fired power plants. This study describes the detailed measurements of combustion characteristics of bituminous and subbituminous coal in a 0.7MWth pilot-scale test facility. This experimental works include the measurement of gas temperature, gas concentrations along with the reactor axial and radial distance at the condition of excess air ratio of 1.2. The solid sampling was carried out and analyzed with the combustion of bituminous coal. The main reaction zone of coal flame in a reactor was formed about 1 m from the swirl burner, and at downstream, the fully developed temperature and species distribution was observed. The sampled particles of bituminous coal in a reactor revealed the complete carbon burn-out was achieved just after an main combustion zone.

• Proceedings of the Korea Contents Association Conference
• /
• 2004.05a
• /
• pp.553-561
• /
• 2004

It works as intermediation of communication of publics these days. Since 20 century, We, Koreans, have established new chaotic multi culture with traditional Korean culture and other different culture from everywhere. Meanwhile, we occupied the most powerful semi-conduct and IT indusry. Within those circumstance, people feel very confused in political, cultural and social aspect. The society armed with economy and popularization promotes material satisfaction with this potential possibility of anonymous masses. However, it results to cause loneliness, isolation, alienation, anonymity, non individuality and commodity of culture. In my work, such phenomenon reveals through human character in a city. People are exposed culture of consumption and surrounded and tempted by all those artificial and superficial atmosphere. Human are possessed and exposed to attractive products and visual images. Finally they make themselves stuck in their case of this world. People lose their own identify and shape of bodies. That is our portrait, who are living this moment. Also, this is a symbol that destroys this modern society. As a result, 1 consider such aspects through those elements above to think how to keep and rethink our identity and what to do for this world.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.4
• /
• pp.55-66
• /
• 1993

Upon freezing a soil swells due to phase change and its compression stress increase a lot. As the soil undergo thawing, however, it becomes a soft soil layer because the 'soil changes from a solid state to a plastic state. These changes are largely dependent on freezing temperature and repeated freezing-thawing cycle as well as the density of the soil and applied loading condition. This study was initiated to describe the effect of the freezing temperature and repeated freezing-thawing cycle on the unconfined compressive strength. Soil samples were collected at about 20 sites where soil structures were installed in Kangwon provincial area and necessary laboratory tests were conducted. The results could be used to help manage effectively the field structures and can be used as a basic data for designing and constructing new projects in the future. The results were as follows ; 1. Unconfined compressive strength decreased as the number of freezing and thawing cycle went up. But the strength increased as compression speed, water content and temperature decreased. The largest effect on the strength was observed at the first freezing and thawing cycle. 2. Compression strain went up with the increase of deformation speed, and was largely influenced by the number of the freezing-thawing cycle. 3. Secant modulus was responded sensitivefy to the material of the loading plates, increased with decrease of temperature down to - -10$^{\circ}$C, but was nearly constant below the temperature. Thixotropic ratio characteristic became large as compression strain got smaller and was significantly larger in the controlled soil than in the soil treated with freezing and thawing processes 4. Vertical compression strength of ice crystal(development direction) was 3 to 4 times larger than that of perpendicular to the crystal. The vertical compression strength was agreed well with Clausius-Clapeyrons equation when temperature were between 0 to 5C$^{\circ}$, but the strength below - 5$^{\circ}$C were different from the equation and showed a strong dependency on temperature and deformation speed. When the skew was less then 20 degrees, the vertical compression strength was gradually decreased but when the skew was higher than that, the strength became nearly constant. Almost all samples showed ductile failure. As considered above, strength reduction of the soil due to cyclic freezing-thawing prosses must be considered when trenching and cutting the soil to construct soil structures if the soil is likely subject to the processes. Especially, if a soil no freezing-thawing history, cares for the strength reduction must be given before any design or construction works begin. It is suggested that special design and construction techniques for the strength reduction be developed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.109-115
• /
• 2019

In arc-welding applying to the present automobile part manufacturing process, a wrist-hollow type arc welding robot can shorten the welding cycle time, because feedability of a welding wire is not affected by a robot posture and thus facilitates high-quality arc welding, based on stable feeding with no entanglement. In this paper, we will propose the optimization of wrist design for a wrist-hollow type 6-Axis articulated robot. Specifically, we will perform the investigation on the optimized design of inner diameter of hollow arms (Axis 4 and Axis 6) and width of the upper arm by using the simulation of robot motion characteristics, using a Genetic Algorithm (i.e., GA). Our simulations are based on $SolidWorks^{(R)}$ for robot modeling, $MATLAB^{(R)}$ for GA optimization, and $RecurDyn^{(R)}$ for analyzing dynamic characteristics of a robot. Especially $RecurDyn^{(R)}$ is incorporated in the GA module of $MATLAB^{(R)}$ for the optimization process. The results of the simulations will be verified by using $RecurDyn^{(R)}$ to show that the driving torque of each axis of the writs-hollow 6-axis robot with the optimized wrist design should be smaller than the rated output torque of each joint servomotor. Our paper will be a guide for improving the wrist-hollow design by optimizing the wrist shape at a detail design stage when the driving torque of each joint for the wrist-hollow 6-axis robot (to being developed) is not matched with the servomotor specifications.

• (The)Study of the Eastern Classic
• /
• no.59
• /
• pp.57-92
• /
• 2015

This study looked into the process by which Haseo(河西) Kim In-hoo(金麟厚:1510~1560), a neo-confucian scholar of mid Joseon Dynasty, was recognized and adored as an inheritor of traditional academic genealogy of neo-confucianism of Joseon Dynasty. I intended to examine the process of personal embodiment affected or excluded in certain manners by various materials covering the lifetime of bygone persons based on the process of such embodiment. The part related to childhood of Haseo was arranged newly to highlight solid relationship between Kim In-hoo and King Injong(仁宗). That was because Kim In-hoo raised the issue of loyalty and fidelity, one of the most important and most contentious issues at that time, in connection with reinstatement of GimyoSarim(己卯士林, progressive political faction with young officials), and King Injong was the king who reinstated Gimyo Sarim. That played a decisive role in establishing the image of Haseo, a classical scholar with unwavering integrity and loyalty. During the Late Joseon Dynasty, canonization of Haseo was made under the leadership of King Jeongjo(正祖) and Seoin(西人) in royal court. In the 17th century, Seoin scholars revised the materials related to lifetime of Kim In-hoo in various way and proofread and published the collection of literary works by Kim In-hoo. That aimed to establish scholastic system associated with Seoin and legitimacy of study as pursued by Seoin. This made progress with adoration towards scholars affiliated with Seoin, including Yulgok(栗谷) Lee Yi(李珥). Finally, King Jeongjo showed strong intention to take the lead as sovereign in the process while Haseo was canonized into national academy in the 18th century. That came from the desire to solidify his status as a teacher who took pride in taking responsibility for the dynasty's authentic study, as well as the king heading the dynasty politically.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.279-292
• /
• 2018

Unlike the global art market which experienced rapid recovery from the impacts of the Global Financial Crisis in 2008, the Korean art market has not yet fully recovered. The gallery-oriented distribution system, vulnerable primary art market functions, and the market structure centered on a small number of collectors make it difficult for young and medium artists to enter the market and, as a result, deepen the economic polarization of artists. In addition, the high price of art works limits market participation by restricting the general public. This study began with the idea that the interest of the public in the art market as well as their participation in the market are urgent. To this end, we noted that public awareness of art transactions can be a starting point for improving the constitution of the fragile art market, focusing on the 'Artist-centered Art Fair' rather than existing art fairs. To examine the contribution of such an art fair to the popularization of the art market, we analyzed the case of the 'Visual Artist Market (VAM)' project of the Korea Arts Management Service. Results found that the 'Artist-centered Art Fair' focuses on providing opportunities for market entry to young and medium artists rather than on the interests of distributors, and promotes the popularization of the art market by promoting low-priced works to the general public. Also, the 'Artist-centered Art Fair' seems to play a primary role in the public sector to foster solid groups of artists as well as to establish healty distribution networks of Korean Art market. However, in the long run, it is necessary to promote sustainable development of the 'Artist-centered Art Fair' through indirect support, such as the provision of a publicity platform or consumer finance support, rather than direct support.

• The korean journal of orthodontics
• /
• v.38 no.4
• /
• pp.240-251
• /
• 2008

Objective: The purpose of this study was to evaluate the effect of head position changes on the root parallelism between adjacent teeth on panoramic radiographs. Methods: A model with normal occlusion was constructed in the SolidWorks program, then RP (rapid protyping) model was fabricated. The model was repeatedly imaged and repositioned five times at each of the following nine positions: ideal head position, $5^{\circ}$ up, $10^{\circ}$ up, $5^{\circ}$ down, $10^{\circ}$ down, $5^{\circ}$, right, $10^{\circ}$, up, and $5^{\circ}$ right rotation, $10^{\circ}$ right rotation. Panoramic radiographs were taken by Planmeca ProMax and the angle between the long axes of adjacent teeth was directly measured in the monitor. Results: Axes of adjacent teeth tended to converge toward the occlusal plane when the head tilted up and converged in the opposite direction to the occlusal plane when the head tilted down. Anterior teeth showed the most notable differences. When one side of the head tilted up $5^{\circ}$ and $10^{\circ}$ along the anteroposterior axis (Y axis), tooth axes of the same side tended to converge toward the occlusal plane and tooth axes of the opposite side tended to converge in the opposite direction to the occlusal plane. When the head rotated to one side along the vertical axis (Z axis), the canine and lateral incisor of the same side converged in the opposite direction to the occlusal plane and the canine and lateral incisor of the other side converged toward the occlusal plane. Conclusions: When assessing the root parallelism on panoramic radiographs, the occlusal plane cant (anteroposterior or lateral) or asymmetry of the dental arch should be considered because these can cause distortion of tooth axes on panoramic radiographs.

• Korean Journal of Community Nutrition
• /
• v.26 no.5
• /
• pp.327-336
• /
• 2021

Objectives: This study was conducted to create a 3D printable snack dish model for the elderly with low food or fluid intake along with barriers towards eating. Methods: The decision was made by the hybrid-brainstorming method for creating the 3D model. Experts were assigned based on their professional areas such as clinical nutrition, food hygiene and chemical safety for the creation process. After serial feedback processes, the grape shape was suggested as the final model. After various concept sketching and making clay models, 3D-printing technology was applied to produce a prototype. Results: 3D design modeling process was conducted by SolidWorks program. After considering Dietary reference intakes for Koreans (KDRIs) and other survey data, appropriate supplementary water serving volume was decided as 285 mL which meets 30% of Adequate intake. To consider printing output conditions, this model has six grapes in one bunch with a safety lid. The FDM printer and PLA filaments were used for food hygiene and safety. To stimulate cognitive functions and interests of eating, numbers one to six was engraved on the lid of the final 3D model. Conclusions: The newly-developed 3D model was designed to increase intakes of nutrients and water in the elderly with dementia during snack time. Since dementia patients often forget to eat, engraving numbers on the grapes was conducted to stimulate cognitive function related to the swallowing and chewing process. We suggest that investigations on the types of foods or fluids are needed in the developed 3D model snack dish for future studies.