• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.267-271
• /
• 2019

A shingled PV module is manufactured by dividing and bonding. In this method, the solar cell is divided by lasers and bonded using electrically conductive adhesives (ECAs). Consequently, the manufacturing cost increases because a process step is added. Therefore, we aim to reduce the production cost by reducing the amount of Ag paste used in the solar cell front. Various electrode structures were designed and simulated. The number of fingers was optimized by designing thinner fingers, and the number of fingers with the maximum power conversion efficiency was confirmed. The simulation confirmed the maximum efficiency in the 4-divided electrode pattern. The amount of Ag paste used for each electrode pattern was calculated and analyzed. The number of fingers was optimized by decreasing the width of the finger; this will not only reduce the amount of Ag paste required but also the increase the efficiency.

• Journal of the Korean Physical Society
• /
• v.73 no.11
• /
• pp.1794-1798
• /
• 2018

We have grown famatinite $Cu_3SbS_4$ films by using sulfurization of Cu/Sb stack film. Sulfurization at $500^{\circ}C$ produced famatinite $Cu_3SbS_4$ phase, while $400^{\circ}C$ and $450^{\circ}C$ sulfurization exhibited unreacted and mixed phases. The fabricated $Cu_3SbS_4$ film showed S-deficiency, and secondary phase of $Cu_{12}Sb_4S_{13}$. The secondary phase was confirmed by X-ray diffraction, Raman spectroscopy, photoluminescence and external quantum efficiency measurements. We have also fabricated solar cell in substrate type structure, ITO/ZnO/(Zn,Sn)O/$Cu_3SbS_4$/Mo/glass, where $Cu_3SbS_4$ was used as a absorber layer and (Zn,Sn)O was employed as a Cd-free buffer. Our best cell showed power conversion efficiency of 0.198%. Characterization results of $Cu_3SbS_4$ absorber indicates deep defect (due to S-deficiency) and low shunt resistance (due to $Cu_{12}Sb_4S_{13}$ phase). Thus in order to improve the cell efficiency, it is required to grow high quality $Cu_3SbS_4$ film with no S-deficiency and no secondary phase.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.13-20
• /
• 2021

GaN has shown good potential owing to its better chemical stability than other materials and tunable bandgap with materials such as InN and AlN. Tunable bandgap allows GaN to make the maximum utilization of the solar spectrum, thus improves the solar-to-hydrogen (STH) efficiency. In addition, GaN band gap contains the oxidation and reduction level of water, so it can split water without external voltage. However, STH efficiency using GaN itself is low and has been actively studied recently to improve it. In this thesis, we have summarized the studies related to the use of GaN as a photoelectrode for photoelectrochemical water splitting.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.153-155
• /
• 2009

In this study, we fabricated the $Cu(In,Ga)Se_2$ (CIGS) thin-film solar cells by using a polyimide substrate. The CIGS thin-film was deposited on Mo coated polyimide substrate by a 3-stage co-evaporation technique. Because the polyimide shows thermal transformation at about $400^{\circ}C$, the substrate temperature of co-evaporation process was set to below $400^{\circ}C$. Corresponding solar cell showed a conversion efficiency of 7.08 % with $V_{OC}$ of 0.58 V, $J_{SC}$ of 24.99 $mA/cm^2$ and FF of 0.49.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.289-290
• /
• 2006

We report a study of Zn(S)Se/GaAs heterojunction solar cells grown by molecular beam epitaxy (MBE). Zn(S)Se/GaAs heterostructures prepared under different conditions were characterized in-situ by reflection high-energy electron diffraction (RHEED). Structural and electrical properties were investigated with double crystal X-ray diffraction and current-voltage characteristics, respectively. The fabricated $n-ZnS_{0.07}Se_{0.93}/p-GaAs$ solar cell (SC #2) exhibited open circuit voltage($V_{oc}$) of 0.37 V, short circuit current($I_{sc}$) of $1.7{\times}10^{-2}$ mA, fill factor of 0.62 and conversion efficiency of 7.8 % under 38.5 $mW/cm^2$ illumination.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4382-4386
• /
• 2011

$TiO_2$ hollow spheres were fabricated by using $SiO_2$ as an inorganic template. Spherical $SiO_2$ particles were coated by $TiO_2$ through the nucleation process, and then the core $SiO_2$ part was eliminated by using HF solution. Finally, $TiO_2$ hollow spheres were obtained. The size of the $TiO_2$ hollow spheres was about 300-400 nm and the thickness of the hollow wall was about 20-30 nm. The hollow has several holes whose diameters were within 100-200 nm. Dye-sensitized solar cells fabricated by using the $TiO_2$ hollow spheres were characterized. The solar conversion efficiency of the cell was 8.45% when $TiO_2$ hollow spheres were used as a scattering material, while it was 4.59% when $TiO_2$ hollow spheres were used as a normal electrode material.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.125-132
• /
• 2010

Three organic sensitizers, JK-128, JK-129, and JK-130 containing quinoline unit are designed and synthesized. Under standard global AM 1.5 solar condition, the JK-130 sensitized solar cell gave a short circuit photocurrent density of 11.52 mA $cm^{-2}$, an open circuit voltage of 0.70 V, and a fill factor of 0.75, corresponding to an overall conversion efficiency of 6.07%. We found that the $\eta$ of JK-130 was higher than those of other two cells due to the higher photocurrent. The higher $J_{sc}$ value is attributed to the broad and intense absorption spectrum of JK-130.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1571-1572
• /
• 2009

Polymer solar cells were fabricated with gravure printing process and the effect of thermal annealing of gravure printed organic layer was investigated. The layer structure of polymer solar cells is glass / ITO / hole transfer layer / active layer / Al structure was fabricated. For the active layer, 1:1 ratio of poly-3-hexylthiophene (P3HT) and [6,6]-phenyl C61-butyric acid methyl ester (PCBM) mixture was applied. The P3HT/PCBM blend was gravure printed onto the substrates. The effect of thermal annealing was investigated by changing annealing time and the number of printing. Maximum 3.6% of power conversion efficiency was achieved with gravure printing of organic layer and thermal annealing in this work.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.66-71
• /
• 1992

We fabricated highly stable a-Si:H solar cell using low band gap intrinsic layer fabricated by RP-CVD. We obtained a-Si:H with optical band gap of less than 1.65 eV with deposition rate of 0.18 $\AA$/sec, and used this material as bottom i-layer of a-Si:H double stacked solar cells. We have succeeded in the fabrication of very stable a-Si:H double stacked solar cell of which the conversion efficiency is about 9% and the degradation is less than 4% after light illumination for 100h under 350mW/cm$^{2}$.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.8
• /
• pp.2321-2324
• /
• 2013

An improved hybrid solar cell was obtained by focusing on the effects of ligand for CdSe nanoparticles, in the active layers. The performance was compared by mixing nanoparticles capped with pyridine or oleic acid for the acceptor material into poly(3-hexylthiophene):[6,6]-phenyl C61 butyric acid methyl ester based active layer. The solar cells with pyridine capped CdSe nanoparticles showed a power conversion efficiency of 2.96% while oleic acid capped CdSe nanoparticles showed 2.85%, under AM 1.5G illumination. Formation of percolation pathways for carrier transport and a reduction in the hopping event resulted in better performance of pyridine capped nanoparticles.