• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.578-584
• /
• 2017

$SiO_2$ buffer layer (100 nm) has been deposited on PET substrate by electron beam evaporation. And then, IZTO (In-Zn-Sn-O) thin film has been deposited on $SiO_2$/PET substrate with different RF power of 30 to 60 W, working pressure, 1 to 7 mTorr, by RF magnetron sputtering. Structural, electrical and optical properties of IZTO thin film have been analyzed with various RF powers and working pressures. IZTO thin film deposited on the process condition of 50 W and 3 mTorr exhibited the best characteristics, where figure of merit was $4.53{\times}10^{-3}{\Omega}^{-1}$, resistivity, $4.42{\times}10^{-4}{\Omega}-cm$, sheet resistance, $27.63{\Omega}/sq.$, average transmittance (400-800 nm), 81.24%. As a result of AFM, all the IZTO thin film has no defects such as pinhole and crack, and RMS surface roughness was 1.147 nm. Due to these characteristics, IZTO thin film deposited on $SiO_2$/PET structure was found to be a very compatible material that can be applied to the next generation flexible display device.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.402.2-402.2
• /
• 2016

In photoelectrochemical (PEC) water splitting, Cu2ZnSnS4 (CZTS) compound has attracted intense attention as a photocathode due to not only large optical absorption coefficient, but also earth-abundance of constituent elements and suitable band alignment. With rapid development of nanotechnology, one-dimensional nanostructures of CZTS have been investigated as a potential form to achieve high efficiency because the nanostructures are expected to be capable of capturing more light and enhancing charge separation and transport. Here, we report a well-controlled fabrication route for vertically-aligned CZTS nanorod arrays on anodic aluminium oxide (AAO) template via simple sol-gel process followed by deposition of ZnS or CdS buffer layers on the CZTS nanorod to enhance charge separation. The structure, morphology, composition, optical absorption, and PEC properties of the resulting CZTS nanorod samples were characterized using X-ray diffraction, Raman spectroscopy, transmission electron microscopy, energy dispersive X-ray spectrometry, scanning electron microscopy, and UV-vis spectroscopy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.151.1-151.1
• /
• 2015

본 연구에서는 $O_2$ 플라즈마 처리에 따른 용액 공정 기반 ITZO 박막 트랜지스터를 제작하여, 산소에 따른 문턱전압 변화를 비교, 분석하였다. 처리시간은 0초에서 50초까지 가변하였다. 전달 곡선으로 트랜지스터의 특성을 평가하고, XPS(X-ray Photoelectron Spectroscopy)를 통해 Zn, In, Sn-O 결합과 산소 결합 결함을 확인하였다. 처리 시간이 증가 할수록 문턱전압이 -6.8V에서 -2.1V로 이동하였다. 처리시간이 길어질수록 OM/OL 비율이 0.4533에서 0.4381로 감소하였고, 또한 산소 결합 결함이 감소하였다. 실험결과를 통해 산소 결합 결함을 조절함으로써 문턱전압이 양의 방향으로 이동함을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.108-108
• /
• 2009

ITO에 사용되는 주된 재료인 인듐의 bixbyite 구조는 TCOs의 전기적 특성에서 매우 중요한 것으로 알려져 있다. 때문에 인듐의 Bixbyite구조를 유지하면서 인듐의 사용량을 줄이기 위해 최적의 Solubility limit에 관해 연구하였다. 이를 위해 In2O3-ZnO-SnO2의 삼성분계 기본 조성에 두가지 물질을 추가로 첨가하여 첨가량에 따른 Solubility limit을 연구하였다. Solubility limit의 측정을 위해 X-ray Diffractometer(XRD)를 사용하였으며, 첨가 원소의 양이 증가할수록 TCOs target의 Latice parameter값은 작아졌다, SEM을 통한 미세구조의 관찰로 원소첨가에 따른 샘플의 소결에너지 변화를 분석할 수 있었다. 제작된 시편의 정성분석 및 Chemical binding Energy를 측정하기 위해 X-ray Photo Spectroscopy (XPS)를 이용하였으며, 전기적인 특성 측정을위해 4-Point prove mesurement 방법을 사용하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.198-203
• /
• 2000

This paper investigated the effects of doping elements on the Bi-Sr-Ca-Cu-O ceramics. The doping elements can be classified into four groups depending on their superconducting characteristics in the Bi-Sr-Ca-Cu-O structure. The first group of doping elements(Co, Fe, Ni and Zn) substitute into the copper site and can reduce the critical temperatures of the 2223 and 2212 phases. The second group of doping elements(Y and La) substitute into the Ca site and cause the disappearance of the 2223 phase and increase the critical temperatures in the 2212 phase. The third group of doping elements(P and K) have a tendency to decompose the superconducting phase and reduce the optimal sintering temperature. The fourth group of doping elements(B, Si, Sn and Ba) almost unaffected the superconductivity of the 2223 and 2212 phase.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.120-120
• /
• 2003

The metallic oxide nanomaterials including ZnO, Ga$_2$O$_3$, TiO$_2$, and SnO$_2$ have been synthesized by a number of methods including laser ablation, arc discharge, thermal annealing procedure, catalytic growth processes, and vapor transport. We have been interested in preparing the nanomaterials of Ga$_2$O$_3$, which is a wide band gap semiconductor (E$_{g}$ =4.9 eV) and used as insulating oxide layer for all gallium-based semiconductor. Ga$_2$O$_3$ is stable at high temperature and a transparent oxide, which has potential application in optoelectronic devices. The Ga$_2$O$_3$ nanoparticles and nanobelts were produced using GaN single crystals, which were grown by flux method inside SUS$^{TM}$ cell using a Na flux and exhibit plate-like morphologies with 4 ~ 5 mm in size. In these experiments, the conventional electric furnace was used. GaN single crystals were pulverized in form of powder for the growth of Ga$_2$O$_3$ nanomaterials. The structure, morphology and composition of the products were studied mainly by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM).).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.279-282
• /
• 2003

For the millimeter-wave dielectrics, Forsterite-based ceramics were produced. Pure forsterite ceramics($Mg_2SiO_4$) shows porous micro-structure and very low Q*f values, which is not suitable for the dielectrics for the millimeter-wave band. Several sintering aids including $Al_2O_3$, $Li_2CO_3$, $Li_2SiO_4$, were added to the forsterite ceramics in order to produce dense low-loss dielectrics. Among these additives, $Li_2CO_3$ is the most effective sintering aids. Several sub-components including NiO, ZnO, $SnO_2$, $TiO_2$, were added to enhance the microwave dielectric properties. $TiO_2$ is the most effective additive to enhance the dielectric properties at microwave bands. The simultaneous addition of $TiO_2$ and $Li_2CO_3$ increases Q*f value over 170,000, which can be used as dielectrics in millimeter-wave bands.

• Archives of design research
• /
• v.17 no.4
• /
• pp.241-250
• /
• 2004

In this research, the copper alloy plates C2200, C5210, C7701, C8113 were selected to make datum and to identify further usage of metal craft experimentation. For its experimentation, the general welding and TIG welding methods were researched; for 2nd experimentation, the Reticulation and Electroforming skill's differences in color and temperature were researched. With these methods 3 different kinds of works are introduced for sample studies. For this research, Dr. Lee, Dong-Woo who works in Poongsan Metal Co, supported 4 kinds of copper alloy metals. Which are Commercial bronze (Cu-Zn), Deoxidiged Copper(Cu-Sn-P), Nickel Silver (Cu-Ni-Zn), and White Bronze (Cu-Ni); they were applied partly and wholly by the method of Laminatin, Reticulation, Fusing, and Electroforming skills. In case of C2200, the brass, the A. C. TIG welding method is better under 2mm slight plate; the D.C. TIG welding is better upper 2mm plate; and 250~300$^{\circ}C$ is recommended for remain heat treatment. In case of C5210, not having Hydrogen in high temperature return period, doesn't need Oxygen in high temperature and hardening in comparative high temperature neither, it is good for welding. It contains Sn 2-9% ad P 0.03-0.4% generally; and in accordance with the growth rate of Sn contain amount, the harden temperature boundary become broad. In case of cold moment after welding, they are recommended that higher speed TIG welding, smaller melting site and less than 200$^{\circ}C$ for pre-heating temperature. In case of C7701, the 10-20% Ni, 15-30% Zn are widely used.. If it is upper 30% Zn, it become (${\alpha}+{\beta}$) system and adhesive power rate become lower, and the productivity become lower in low temperature but the productivity become higher in high temperature. Nickel Silver's resistance of electricity is well; and the heatproof and incorrodibility is good, too. Lastly, in case of C8113, good at persistence in salty and grind; high in strength of high temperature. In case of white brass, contain 10-30% Nickel and hardened in high temperature and become single phrase. For these reason, the crystallization particles easily become large, if the resistance become higher small amount of Pb, P, S separation rate become higher.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.341-341
• /
• 2011

최근 AMOLED 구동이 가능한 소자에 대한 연구가 활발히 진행중이다. AMOLED구동 가능소자는 LTPS TFT, a-Si TFT, OTFT, Oxide TFT가 있으며 그 중에서 현재 대부분 LTPS TFT를 사용하고 있다. LTPS TFT는 높은 전자 이동도와 안정성을 가지고 있기 때문에 현재 각광 받는 AMOLED에 잘 맞는다. 하지만 LTPS TFT는 고비용, 250$^{\circ}C$ 이상의 공정온도, Substrate가 Glass, Metal로 제한 된다는 문제점이 있으며, 균일성이 낮고 현재 대면적 기술이 부족한 상태이다. 해결방안으로 AMOLED를 타겟으로 하는 Oxide TFT 기술이 떠오르고 있다. Oxide TFT는 이동도가 높고 저온공정이 가능하며 Substrate로 Plastic 기판을 사용할 수가 있어 차후에 Flexible 소자로서의 적용이 가능하다. 또한 기존의 진공장비 사용대신 용액공정이 가능하여 장비사용시간 및 절차를 단축시킬 수 있어 비용적인 유리함을 가지고 있다. Oxide TFT는 단결정 산화물과 다결정 복합 산화물 두 가지 범주를 가지고 있다. Oxide TFT의 재료물질은 ZnO, ZTO, IZO, SnO2, Ga2O3, IGO, In2O3, ITO, InGaO3(ZnO)5, a-IGZO이 있다. 본 연구에서는 산화물질 중 하나인 ZTO를 이용하여 TFT 소자를 제작하였다. 산화물 특성상 열처리 온도에 따라 형성되는 결정의 정도가 다르기 때문에 온도 및 시간 변수에 따른 ZTO의 특성변화에 초점을 맞추어 연구함으로서 최적화된 조건을 찾고자 실험을 진행하였다. 실험을 위한 기판으로 n-type wafer을 사용하였다. PE-CVD 장비를 이용하여 SiNx를 120 nm 증착하고, ZTO 용액을 spin-coating을 이용하여 channel layer을 형성하였다. 균일하게 형성된 ZTO의 결정을 위하여 200$^{\circ}C$, 300$^{\circ}C$, 400$^{\circ}C$, 500$^{\circ}C$에서 1시간, 3시간, 6시간, 10시간의 온도 및 시간 변수를 두어 공기 중에서 열처리 하였다. ZTO는 약 30 nm 두께로 형성되었다. Thermal evaporator를 이용하여 Source, Drain의 알루미늄 전극을 형성하고, wafer 뒷면에는 Silver paste를 이용하여 Gate전극을 만들었다. 제작된 소자를 dark room temperature에서 측정하였다.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.384-390
• /
• 2005

[ ${\alpha}-Al_2O_3$ ] precursor was synthesised by sol-gel method using aluminum sulfate, sodium sulfate and sodium carbonate as law materials. The flaky ${\alpha}-Al_2O_3$ crystals were prepared by heating using precursor about $1,050^{\circ}C$. In this study, the effect of some transition-metal sulfate ($FeSO_4,\;SnSO_4,\;ZnSO_4$) addition have been investigated. When iron sulfate was added, it could see that act on impurities in crystal growth process. In case of tin sulfate, distribution of Platelets was very broad. When flaky ${\alpha}-Al_2O_3$ crystals were prepared zinc sulfate addition, thickness, size, and distribution of platelets was suited to industrial application. The average diameter of flaky ${\alpha}-Al_2O_3$ crystals was about 20 $\mu$m, and its thickness was about 0.3 $\mu$m. Increasing addition of zinc sulfate, thickness of ${\alpha}-Al_2O_3$ platelet was decreased.