• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.335-335
• /
• 2014

Over the past several years, transparent conducting oxides have been extensively studied in order to replace indium tin oxide (ITO). Here we report on fluorine doped zinc tin oxide (FZTO) films deposited on glass substrates by radio-frequency (RF) magnetron sputtering using a 30 wt% ZnO with 70 wt% SnO2 ceramic targets. The F-doping was carried out by introducing a mixed gas of pure Ar, CF4, and O2 forming gas into the sputtering chamber while sputtering ZTO target. Annealing temperature affects the structural, electrical and optical properties of FZTO thin films. All the as-deposited FZTO films grown at room temperature are found to be amorphous because of the immiscibility of SnO2 and ZnO. Even after the as-deposited FZTO films were annealed from $300{\sim}500^{\circ}C$, there were no significant changes. However, when the sample is annealed temperature up to $600^{\circ}C$, two distinct diffraction peaks appear in XRD spectra at $2{\Theta}=34.0^{\circ}$ and $52.02^{\circ}$, respectively, which correspond to the (101) and (211) planes of rutile phase SnO2. FZTO thin film annealed at $600^{\circ}C$ resulted in decrease of resistivity $5.47{\times}10^{-3}{\Omega}cm$, carrier concentration ~1019 cm-3, mobility~20 cm2 V-1s-1 and increase of optical band gap from 3.41 to 3.60 eV with increasing the annealing temperatures and well explained by Burstein-Moss effect. Change of work function with the annealing temperature was obtained by ultraviolet photoemission spectroscopy. The increase of annealing temperature leads to increase of work function from ${\phi}=3.80eV$ (as-deposited FZTO) to ${\phi}=4.10eV$ ($600^{\circ}C$ annealed FZTO) which are quite smaller than 4.62 eV for Al-ZnO and 4.74 eV for SnO2. Through X-ray photoelectron spectroscopy, incorporation of F atoms was found at around the binding energy of 684.28 eV in the as-deposited and annealed FZTO up to 400oC, but can't be observed in the annealed FZTO at 500oC. This result indicates that F atoms in FZTO films are loosely bound or probably located in the interstitial sites instead of substitutional sites and thus easily diffused into the vacuum from the films by thermal annealing. The optical transmittance of FZTO films was higher than 80% in all specimens and 2-3% higher than ZTO films. FZTO is a possible potential transparent conducting oxide (TCO) alternative for application in optoelectronics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.420-420
• /
• 2014

최근, 과학 기술이 발달함에 따라 현장에서의 실시간 검사 및 자가 지단 등 질병 치유에 대한 사람들의 관심이 증가하고 있으며, 이에 따라 의료, 환경, 산업과 같은 많은 분야에서 바이오 센서에 대한 연구가 활발하게 이루어지고 있다. 그 중, EGFET는 전해질 속의 각종 이온 농도를 전기적으로 측정하는 바이오 센서로, 외부 환경으로부터 안전하고, 제작이 쉬우며, 재활용이 가능하여 비용을 절감 할 수 있다는 장점을 가지고 있다 [1]. EGFET는 감지부와 FET부로 분리된 구조를 가지고 있으며, 감지부의 감지막으로는 Al2O3, HfO2, $TiO_2$, SnO2 와 같은 다양한 물질들이 사용되고 있다. 그 중, SnO2는 우수한 감도와 안정성을 가지고 있는 물질로 추가적인 열처리 공정 없이도 우수한 감지 특성을 나타내기 때문에 본 연구에서 감지막으로 사용하였다. 한편, EGFETs 의 FET부로는 기존의 비정질 실리콘 TFTs 에 비해 10배 이상의 높은 이동도와 온/오프 전류비를 갖는 InGaZnO 를 채널층으로 사용한 TFTs 를 사용하였다. a-IGZO 는 넓은 밴드 갭으로 인해 가시광 영역에서 투명하며, 향후 투명 바이오센서 제작 시, 물질들 사이의 반응을 전기적 신호뿐만 아니라 광학적인 분석 방법으로도 검출이 가능하기에 고 신뢰성을 갖는 센서의 제작이 가능할 것으로 기대된다. 한편, a-IGZO TFTs 의 경우 우수한 전기적 특성을 나타냄에도 불구하고 소자 동작 시 문턱 전압이 불안정하다는 단점이 있으며 [2], 이러한 문제의 개선과 향후 투명 기판 위에서의 소자 제작을 위해서는 저온 열처리 공정이 필수적이다. 따라서, 본 연구에서는 저온 열처리 공정인 u-wave 열처리를 통하여 a-IGZO TFTs 의 전기적 특성 및 안정성을 향상시켰으며, 9.51 [$cm2/V{\cdot}s$]의 이동도와 135 [mV/dec] 의 SS값, 0.99 [V]의 문턱 전압, 1.18E+08의 온/오프 전류 비를 갖는 고성능 스위칭 TFTs 를 제작하였다. 최종적으로, 제작된 a-IGZO TFTs 를 SnO2 감지막을 갖는 EGFETs 에 적용함으로써 우수한 감지 특성과 안정성을 갖는 바이오 센서를 제작하였다.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.6
• /
• pp.353-362
• /
• 2022

Recently, transmittance of photomasks for ultra-violet (UV) region is getting more important, as the light source wavelength of an exposure process is shortened due to the demand for technologies about high integration and miniaturization of devices. Meanwhile, such problems can occur as damages or the reduction of yield of photomask as electrostatic damage (ESD) occurs in the weak parts due to the accumulation of static electricity and the electric charge on chromium metal layers which are light shielding layers, caused by the repeated contacts and the peeling off between the photomask and the substrate during the exposure process. Accordingly, there have been studies to improve transmittance and antistatic performance through various functional coatings on the photomask surface. In the present study, we manufactured antireflection films of Nb₂O₅, | SiO₂ structure and antistatic films of ITO designed on 100 × 100 × 3 mmt sodalime glass by DC magnetron sputtering system so that photomask can maintain high transmittance at I-line (365 nm). ITO thin film deposited using In/Sn (10 wt.%) on sodalime glass was optimized to be 10 nm-thick, 3.0 × 103 𝛺/☐ sheet resistance, and about 80% transmittance, which was relatively low transmittance because of the absorption properties of ITO thin film. High average transmittance of 91.45% was obtained from a double side antireflection and antistatic thin films structure of Nb₂O₅ 64 nm | SiO₂ 41 nm | sodalime glass | ITO 10 nm | Nb₂O₅ 64 nm | SiO₂ 41 nm.

• Journal of the Korean Ceramic Society
• /
• v.27 no.1
• /
• pp.35-42
• /
• 1990

In the present investigation, ceramic PZT and Polymer were prepared. The former is Pb[(Sn1/2Sb1/2)0.1 Ti0.27Zr0.63]O3 including Pb(Sn1/2Sb1/2)O3 with good pyroelectric effect, and the latter PVA(Poly Vinyl Alcohol) with good plasticity. Then, they were fabricated to be flat by using 0-3 connectivity which is rather easily fabricated and capable of making thin film, extending surface area among the connectivities. Such were applied to the sample as variation of intensity of poling field, poling temperature, volume fraction between ceramic and polymer. Then dielectric constant, pyroelectric current, pyroelectric coefficient and the figure of merit were measured. And then their effects on pyroelectric characteristics were observed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.251-251
• /
• 2011

본 연구에서는 Zr이 도핑 된 ZnSnO (ZZTO) 기반의 물질을 액상공정을 이용하여 합성하고, 박막트랜지스터를 제작하였다. 출발 물질로써 지르코늄 클로라이드 (ZrCl4), 아연 아세테이트 디하이드레이트 ($Zn(CH_3COO)_2{\cdot}2H_3O$), 틴 클로라이드 ($SnCl_2$)를 아연과 주석 프리커서의 비율을 4:7로 고정하고, 지르코늄 프리커서의 몰비를 변형시켜 제작하였다. 제작된 솔루션은 0.25몰의 몰 농도로 고정하였다. 솔벤트로는 2-메톡시에탄올 (2-methoxyethanol)을 사용하였으며, 준비된 솔루션은 $0.2{\mu}m$ 필터를 이용하여 필터링을 실시하였다. Heavily doped p+ Si 기판에 열적 산화법을 이용하여 120 nm 두께의 $SiO_2$를 성장시킨 것을 게이트 및 게이트 절연막으로 이용하였으며, 스핀코팅을 이용하여 ZZTO 박막을 코팅하였다. 코팅 된 기판은 $300^{\circ}C$에서 $500^{\circ}C$ 사이로 2시간 열처리를 실시하였으며, 마지막으로 소오스/드레인을 스퍼터링법으로 Al을 증착하였다. Zr 함량비, 열처리 온도, 제작된 솔루션의 온도에 따른 박막단계를 파악하기 위해 X-ray photoelectron spectroscopy (XPS), thermogravimetry differential thermal analyzer (TG-DTA), X-ray diffractometer (XRD), high-resolution transmission electron microscopy (HR-TEM), Hall-effect measurement, UV-Vis spectroscopy 분석을 실시하였으며, 제작된 소자는 semiconductor analyzer (HP4156C)를 이용하여 측정하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.5
• /
• pp.515-523
• /
• 2015

In this paper, we fabricated and evaluated the gas sensor for the detection of CO gas and $NO_X$ gas among the vehicle exhaust emission gasses. The $SnO_2$ (tin dioxide) layer is used as the detection material, and the thin-film type and the nano-fiber type layers are deposited with various thicknesses using sputtering method and electro spinning method, respectively. The experiments are performed in the chamber where the gas concentration is controlled with mass flow controller. The fabricated devices are applied to the CO and $NO_X$ gas, where the device with the thinner $SnO_2$ layer shows better sensitivity. The nano-fiber has the larger surface area, and the shorter response time and recovery time are obtained. From the experimental results, both types of gas sensors successfully detect CO and $NO_X$ gases, which can be applied to measure those gases from the vehicle emissions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.805-810
• /
• 2012

Transparent conducting oxides (TCOs) have wide range of application areas in transparent electrode for display devices, Transparent coating for solar energy heat mirrors, and electromagnetic wave shield. $SnO_2$ is intrinsically an n-type semiconductor due to oxygen deficiencies and has a high energy-band gap more than 3.5 eV. It is known as a transparent conducting oxide because of its low resistivity of $10^{-3}{\Omega}{\cdot}cm$ and high transmittance over 90% in visible region. In this study, co-doping effects of Al and Y on the properties of $SnO_2$ were investigated. The addition of Y in $SnO_2$ was tried to create oxygen vacancies that increase the diffusivity of oxygen ions for the densification of $SnO_2$. The addition of Al was expected to increase the electron concentration. Once, we observed solubility limit of $SnO_2$ single-doped with Al and Y. $\{(x/2)Al_2O_3+(x/2)Y_2O_3\}-SnO_2$ was used for the source of Al and Y to prevent the evaporation of $Al_2O_3$ and for the charge compensation. And we observed the valence changes of aluminium oxide because generally reported of valence changes of aluminium oxide in Tin - Aluminium binary system. The electrical properties, solubility limit, densification and microstructure of $SnO_2$ co-doped with Al and Y will be discussed.

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.63-68
• /
• 2007

유리를 기판으로 하는 superstrate pin 비정질 실리콘 태양전진에서 전면 투명전도막(TCO)과 p-층의 계면은 태양전지 변환효율에 큰 영향을 미친다. 면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는 $SnO_2:F$보다 전기, 광학적으로 우수하고, 안개율 (Haze)높으며, 수소 플라즈마에서 안정성이 높은 특징을 갖고 있다. 그래서 박막 태양전지의 특성향상에 매우 유리하나, 태양전지로 제조했을 때, $SnO_2$보다 충진율(Fill Factor:F.F)과 $V_{oc}$가 감소한다는 단점을 가지고 있다. 본 실험실에서는 $SnO_2:F$dml F.F.가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과, $SnO_2:F$보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer에 $R=(H_2/SiH_4)=25$로 변화, p ${\mu}c$-Si:H/p a-SiC:H로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p ${\mu}c$-Si:H/p a-SiC:H 인 p-layer 이중 증착에서 $V_{oc}$는 0.95V F.F는 70%이상이 나왔다. 이들 각 p층의 $E_a$(Activiation Energy)를 구해본 결과, ${\mu}c$-Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.72-72
• /
• 2011

Recently, Zinc oxide (ZnO) nano-structures have been received attractive attention because of their outstanding optical and electrical properties. It might be a promising material considered for applications to photonic and electronic devices such as ultraviolet light emitting diode, thin film transistor, and gas sensors. ZnO nano-structures can be typically synthesized by the VLS growth mode and self-assembly. In the VLS growth mode using various growth techniques, the noble metal catalysts such as Au and Sn were used. However, the growth of ZnO nano-structures on nano-crystalline Au seeds using radio frequency (RF) magnetron sputtering might be explained by the profile coating, i.e. the ZnO nano-structures were a morphological replica of Au seeds. Ga doped ZnO (ZnO:Ga) nano-structures using this concept were synthesized and characterized by XRD, AFM, SEM, and TEM. We found that surface morphology is drastically changed from initial islands to later sun-flower typed nano-structures. We will present the structural evolution of ZnO:Ga nano-structures with increasing the film thickness.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.840-845
• /
• 2002

As an ozone gas sensor, the semiconductor gas sensor which is cheap, portable and simple in use and has a high sensitivity and an excellent selectivity, has been known as an alternative. In the present study, ITO ($In_2O_3 95%,\;SnO_2$ 5%) thin films were deposited on the alumina substrate by using R.F. magnetron sputtering method. The substrate temperature was 300$^{\circ}C$ and 500$^{\circ}C$, respectively and then some specimens were annealed at 500$^{\circ}C$ for 4h in air. ITO gas-sensing films formed crystallines before and after annealing. As results of gas sensitivity measurements to an ozone gas, the sensor deposited at 300$^{\circ}C$ and then annealed has the highest sensitivity (sensible below 1 ppm). As the operating temperature increased gradually, the sensitivity decreased but the response time and stability improved.