• The Journal of the Acoustical Society of Korea
• /
• v.23 no.7
• /
• pp.540-547
• /
• 2004

Since speech enhancement algorithms based on Kalman/Wiener filter require a priori knowledge of the noise and have focused on the minimization of the variance of the estimation error between clean and estimated speech signal, small estimation error on the noise statistics may lead to large estimation error. However, H/sub ∞/ filter does not require any assumptions and a priori knowledge of the noise statistics, but searches the best estimated signal among the entire estimated signal by applying least upper bound, consequently it is more robust to the variation of noise statistics than Kalman/Wiener filter. In this paper, we Propose a speech enhancement method using HMM and multi H/sub ∞/ filters. First, HMM parameters are estimated with the training data. Secondly, speech is filtered with multiple number of H/sub ∞/ filters. Finally, the estimation of clean speech is obtained from the sum of the weighted filtered outputs. Experimental results shows about 1dB∼2dB SNR improvement with a slight increment of computation compared with the Kalman filter method.

• Progress in Medical Physics
• /
• v.15 no.1
• /
• pp.54-58
• /
• 2004

The aim of this study was to develop special birdcage resonators for small objects including the human wrist, hand and small animals, using 3T MRI/MRS. Before substantial development, different types of parameters were arranged, based on theoretical analysis, through lumped element transmission line theory. The primary analysis was peformed with a network analyzer (HP 4195A) and the final experimental analysis was carried out with 3T MRI (Medinus, Korea). The manufactured birdcage resonator is typically composed of 12-element structures to which a low-pass filter is fundamentally applied. The diameter and length of each element of the birdcage resonator were as follows: (1) diameter 12 cm, length of element 22 cm, (2) diameter 15 cm, length of element 22 cm, and (2) diameter 17 cm, length of element 25 cm. Copper tape with a width of 1 cm was used for the coils. MRI acquisition parameters were TR=500 ms, TE=17 ms, and Ave=2 for T1-WT images, and TR=4,000 ms, TE=96 ms, and Ave=2 for T2-WT images. The ratio of the samples diameter to the birdcage resonators diameter was approximately 55%, 63% and 70%, respectively, for the three elements. This study determined that the best image quality and S/N ratio were obtained when the ratio of the object's diameter was approximately 50∼80%. A general theoretical analysis of the birdcage coil differs in many respects from the experimental results which were influenced by many factors that were not considering when the general theoretical analysis of the birdcage coil was peformed. The induced resistance may be considered as part of the resistive loss if the quantitative value can be determined using a radiation resistance approach.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2155-2161
• /
• 2015

This study suggests an optical method to measure cardinal of gait (step width, step length, and stride length) with position sensitive detector (PSD). The effect of reflector’s shape (flat and cylinder) on the PSD output voltage was examined for the application of the suggested system to real situations with a curved shape reflector (e.g. shoes). Various mathematical models were evaluated to find the optimal equation for the distance measurement. Considering the effect of shape on detected signal, the inverse polynomial model was developed. The suggested method is simple to operate, low in cost, small in size, and can evaluate gait parameters in real time. This method is expected to be useful in the field of rehabilitation and sport science

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.7A
• /
• pp.776-785
• /
• 2008

Compared with the existing cellular base station whose radio parameters are configured manually, the small base station named as self-configurable base station configures its radio parameters automatically by the central controller. When installing the self-configurable base station, it should be considered primarily that the seamless coverage for the target area is secured while the signal interference to the existing cellular service area must to be minimized. In order to achieve this, it is very important to select the correct radio parameters, e.g., transmission power and working frequency. In this work, we formulate and solve the optimization problem by using mixed integer programming to optimize the air parameter for the self-configurable base stations.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.195-205
• /
• 2013

The analysis of electroencephalographic signal associated with the attention is essential for the understanding of human cognition. In this paper, the characteristic differences between the attention and inattention status in the brain were inspected by nonlinear analysis. The recurrence quantification analysis was applied to the relatively small number of samples of evoked potential having time varying characteristics, where the recurrence plot (RP), the color recurrence plot (CRP), and mean and time-sequential trend parameters were extracted. The dimension and the time delay in phase transformation can be determined by the paired set of extracted parameters. It is observed from RP, CRP, and parameters that the brain dynamics in attention is more complex than that in the inattention, as well as the synchronized brain response is stable in the mean sense but locally time varying. It is feasible that the non-linear analysis method can be useful for the analysis of complex brain dynamics associated during visual attentional task.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.27 no.2
• /
• pp.111-127
• /
• 2023

Purpose: Gallium-68 (⁶⁸Ga) is increasingly used in nuclear medicine imaging for various conditions such as lymphoma and neuroendocrine tumors by labeling tracers like Prostate Specific Membrane Antigen (PSMA) and DOTA-TOC. However, compared to Fluorine-18 (¹⁸F) used in conventional nuclear medicine imaging, ⁶⁸Ga has lower spatial resolution and relatively higher Signal to Background Ratio (SBR). Therefore, this study aimed to investigate the optimized parameters and reconstruction methods for PET/CT imaging using the ⁶⁸Ga radiotracer through model-based image evaluation. Materials and Methods: Based on clinical images of ⁶⁸Ga-PSMA PET/CT, a NEMA/IEC 2008 PET phantom model was prepared with a Hot vs Background (H/B) ratio of 10:1. Images were acquired for 9 minutes in list mode using DMIDR (GE, Milwaukee WI, USA). Subsequently, reconstructions were performed for 1 to 8 minutes using OS-EM (Ordered Subset Expectation Maximization) + TOF (Time of Flight) + Sharp IR (VPFX-S), and BSREM (Block Sequential Regularized Expectation Maximization) + TOF + Sharp IR (QCFX-S-400), followed by comparative evaluation. Based on the previous experimental results, images were reconstructed for BSREM + TOF + Sharp IR / 2 minutes (QCFX-S-2min) with varying β-strength values from 100 to 700. The image quality was evaluated using AMIDE (freeware, Ver.1.0.1) and Advanced Workstation (GE, USA). Results: Images reconstructed with QCFX-S-400 showed relatively higher values for SNR (Signal to Noise Ratio), CNR (Contrast to Noise Ratio), count, RC (Recovery Coefficient), and SUV (Standardized Uptake Value) compared to VPFX-S. SNR, CNR, and SUV exhibited the highest values at 2 minutes/bed acquisition time. RC showed the highest values for a 10 mm sphere at 2 minutes/bed acquisition time. For small spheres of 10 mm and 13 mm, an inverse relationship between β-strength increase and count was observed. SNR and CNR peaked at β-strength 400 and then decreased, while SUV and RC exhibited a normal distribution based on sphere size for β-strength values of 400 and above. Conclusion: Based on the experiments, PET/CT imaging using the ⁶⁸Ga radiotracer yielded the most favorable quantitative and qualitative results with a 2 minutes/bed acquisition time and BSREM reconstruction, particularly when applying β-strength 400. The application of BSREM can enhance accurate quantification and image quality in ⁶⁸Ga PET/CT imaging, and an optimization process tailored to each institution's imaging objectives appears necessary.

• Advances in aircraft and spacecraft science
• /
• v.5 no.2
• /
• pp.225-237
• /
• 2018

The difficulties of satellite vibration testing are due to the commonly expressed qualification requirements being incompatible with the limited performance of the entire controlled system (satellite + interface + shaker + controller). Two features cause the problem: firstly, the main satellite modes (i.e., the first structural mode and the high and low tank modes) are very weakly damped; secondly, the controller is just too basic to achieve the expected performance in such cases. The combination of these two issues results in oscillations around the notching levels and high amplitude beating immediately after the mode. The beating overshoots are a major risk source because they can result in the test being aborted if the qualification upper limit is exceeded. Although the abort is, in itself, a safety measure protecting the tested satellite, it increases the risk of structural fatigue, firstly because the abort threshold has been already reached, and secondly, because the test must restart at the same close-resonance frequency and remain there until the qualification level is reached and the sweep frequency can continue. The beat minimum relates only to small successive frequency ranges in which the qualification level is not reached. Although they are less problematic because they do not cause an inadvertent test shutdown, such situations inevitably result in waiver requests from the client. A controlled-system analysis indicates an operating principle that cannot provide sufficient stability: the drive calculation (which controls the process) simply multiplies the frequency reference (usually called cola) and a function of the following setpoint, the ratio between the amplitude already reached and the previous setpoint, and the compression factor. This function value changes at each cola interval, but it never takes into account the sensor signal phase. Because of these limitations, we firstly examined whether it was possible to empirically determine, using a series of tests with a very simple dummy, a controller setting process that significantly improves the results. As the attempt failed, we have performed simulations seeking an optimum adjustment by finding the Least Mean Square of the difference between the reference and response signal. The simulations showed a significant improvement during the notch beat and a small reduction in the beat amplitude. However, the small improvement in this process was not useful because it highlighted the need to change the reference at each cola interval, sometimes with instructions almost twice the qualification level. Another uncertainty regarding the consequences of such an approach involves the impact of differences between the estimated model (used in the simulation) and the actual system. As limitations in the current controller were identified in different approaches, we considered the feasibility of a new controller that takes into account an estimated single-input multi-output (SIMO) model. Its parameters were estimated from a very low-level throughput. Against this backdrop, we analyzed the feasibility of an LQG control in cancelling beating, and this article highlights the relevance of such an approach.

• Journal of the Institute of Convergence Signal Processing
• /
• v.25 no.2
• /
• pp.86-93
• /
• 2024

This study evaluates the stability of a 4.99-ton small coastal fishing boat using data interpreted according to the second-generation intact stability criteria of the International Maritime Organization (IMO). The focus is on the ship's behavior under surfriding/broaching conditions during sea navigation, ensuring compliance with international standards. The data processing procedures presented apply stricter criteria than the first-generation intact stability standards to assess the ship's intact stability in waves. However, if the vessel deviates from its standard condition, a separate intact stability assessment based on actual loading conditions is necessary. The surfriding/broaching data processing procedures utilized a program developed by the Shipbuilding and Ocean Equipment Research Center at Kunsan National University. The results were analyzed and compared in detail according to the conditions, parameters, and criteria used for the calculations. Additionally, the study presents the results of Level 1 and Level 2 assessments according to IMO regulations, providing a parametric analysis of the small coastal fishing boat's stability. This allows for the evaluation of intact stability in hydrodynamic motion scenarios.tract.

• Journal of Sensor Science and Technology
• /
• v.5 no.1
• /
• pp.43-50
• /
• 1996

This paper presents a manufacture of the multiple subjects biotelemetry system using custom CMOS IC fabricated $1.5{\mu}m$ n-well process technology. The implantable circuits of the system except sensor interface circuits including FM transmitter are fabricated on a single chip with the sire of $4{\times}4mm^{2}$. It is possible to assemble the implantable system in a hybrid package as small as $3{\times}3{\times}2.5cm$ by using this chip, It's main function is to enable continuous measurement simultaneously up to 7-channel physiological signals from the selected one among 8 subjects. Another features of this system are to enable continuous measurement of physiological signals, and to accomplish ON/OFF switching of an implanted battery by subject selection signal with command signal from the external circuit. If this system is coupled with another appropriate sensors in medical field, various physiological parameters such as pressure, pH and temperature are to be measured effectively in the near future.

• Journal of the Institute of Convergence Signal Processing
• /
• v.6 no.4
• /
• pp.191-197
• /
• 2005

Biped walking is the main feature of a humanoid robot. In a biped walking robot, there are many actuators to be controlled and many sensors to be interfaced. In this paper, we propose a DSP-based controller for a miniature biped walking robot with 21 RC servo motors. The proposed controller has a hierarchical structure; a host PC, a DSP-based main controller, and an auxiliary controller with an FPGA chip. The host PC generates and transmits the robot walking data for given walking parameters such as stride, walking period, etc. The main controller implemented with a TMS320LF2407A controls 21 RC servo motors via the auxiliary controller. We also perform some experiments for balancing motion and walking on a slope terrain with interfacing a 2-axis acceleration sensor and a TMS320LF2407A.