• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2916-2921
• /
• 2008

This paper presents the performance and characteristics of small spark-ignited small 2-stroke engine. A single cylinder, two-stroke, air cooled 23cc SI engine for brush-cutter was used in this study. For the performance of the engine, rpm, torque, fuel consumption and lubricate oil consumption were measured, and also HC, CO, NOx emissions and excess air ratio according to throat open ratio under two lubrication method were measured and analyzed. The results showed that maximum of engine rpm is nearly same in both methods and also, torque, power is similar. exhaust emissions tend to decrease with throat open ratio.

• 한국자동차공학회논문집
• /
• 제7권5호
• /
• pp.9-15
• /
• 1999

A digital CDI(Capacitive Discharge Ignition) system on small two stroke motorcycle engine was developed in this paper, This CDI system with microprocessor as its main part has more flexible spark timing than the conventional CDI system because of its programmable characteristics. The principle of this digital CDI system and the design methods of hardware and software were presented in this paper, Two stroke small engine was tested to investigate the performance of digital CDI system And also this system was investigated to optimize the engine performance. Also comparison between conventional CDI can provide better spark timing variation than the conventional system. The part and full load test results show that the engine power was increased about 10-20% and fuel consumption was decreased about 10-20% simultaneously. Furthermore, this digital CDI system has simple structure, low cost and very little modification are required. It is a promising technology to substitute for the widely used conventional CDI system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3341-3346
• /
• 2007

This paper presents effects of carburetor throttle angle on the performance characteristics of a small sparkignited, gasoline engine. The engine used in the test is a single cylinder, two-stroke, air-cooled 26cc SI engine for brush-cutter. We measured the rpm, torque, power, and fuel consumption according to the six different throttle angle conditions of the rotary-type carburetor and to the engine dynamometer loads. We had concluded that maximum power happened at 5000${\sim}$6000rpm and at the same condition was the minimum specific fuel consumption.

• 한국분무공학회지
• /
• 제14권1호
• /
• pp.28-33
• /
• 2009

This paper presents the performance and emissions characteristics of a small spark-ignited 2-stroke gasoline and LPG engine. The engine used in this paper is a single cylinder, two-stroke, air-cooled SI engine for brush cutter. We measured the rpm, torque, fuel consumption and HC, CO, NOx emissions in associated with the dynamometer load at WOT. The results showed that as engine revolution speed decreased, the excess air ratio of gasoline engine kept going about 0.9 and that of LPG engine increased 0.83 to 1.05. Torque and power of gasoline engine was higher than LPG engine. In exhaust emissions, HC emissions of gasoline engine was lower than LPG engine. In low speed area, CO emissions of LPG engine was lower than gasoline engine. Both gasoline engine and LPG engine emitted little NOx emissions.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.409-412
• /
• 2008

This paper presents the effects of excess air factors(0.84${\sim}$0.90) and opened throttle area ratios(AR=0.15${\sim}$0.25) on the emission and performance of a small spark-ignition gasoline engine. The engine used in this paper was a single cylinder, diaphragm carburetor, two-stroke, air-cooled 26cc engine for brush cutter. The rpm, torque, fuel consumption and CO emission were measured under the four different excess air factors and three different opened area ratios conditions on the engine loads respectively. The results showed that the rpm was decreased and torque was increased at increasing load, the maximum power and minimum fuel consumption could be obtained critical rpm on each throttle opened area ratios and brake specific fuel consumption was decreased 13${\sim}$17%, CO emissions was decreased 21${\sim}$38% at excess air factor 0.90 than 0.84.

• 한국수소및신에너지학회논문집
• /
• 제33권3호
• /
• pp.255-260
• /
• 2022

Hydrogen gas fuel was applied to a small-sized two stroke engine for a mobile power source instead of gasoline fuel. Port fuel supply showed a limitation in terms of power due to the back fire at the engine intake manifold. So in this study, hydrogen direct injection system was applied to overcome this drawback by using a low pressure direct gas injector. The result from this strategy showed that hydrogen direct injection improved fuel efficiency as well as torque and power comparing to the port fuel supply system.

• 한국가스학회지
• /
• 제24권6호
• /
• pp.28-33
• /
• 2020

수소 연료를 적용한 2행정 기반의 소형 SI 엔진의 성능 특성에 관하여 살펴보았다. 이를 위하여 주로 모형 항공기용으로 사용되는 210 cc급 엔진을 비롯하여 소형 동력계 및 수소연료와 엔진 오일 공급을 위한 장치를 포함한 실험을 구성하였다. 우선 가솔린 연료를 공급한 기본 상태의 엔진 출력과 토크를 측정해 보았으며, 최대 6 kW 수준의 출력을 확인하였다. 이후 수소 연료를 공급하면서 성능 시험을 수행하였는데, 수소의 경우에는 공기과잉율 기준 공연비가 낮아질수록 즉, 연료 공기 혼합기가 농후해 질수록 역화 현상이 발생하여 출력에 제한이 생길 뿐만 아니라 엔진 하드웨어에도 치명적인 영향을 줌을 확인하였다. 따라서 공기과잉율을 기준 수치 이상에서 엔진을 운전하며 안정적인 수준의 연소를 통하여 가솔린 성능의 절반 수준인 최대 3 kW 의 출력 성능이 나옴을 최종 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권4호
• /
• pp.53-61
• /
• 1988

Speed of a diesel engine is usually controlled by the hydraulic governor which uses the centrifugal force of rotating fly balls for sensing the error speed. But for a recently developed high efficient, low speed and long stroke 2 cycle marine diesel engine, this governor doesn't work well enough because of too much changes of toraring force during one revolution of engine and too long uncontrollable time due to small numbers of cylinder. For improvement of jiggling phenomena and unstability various studies are being carried out, but they are not enough for a steep load change in a small ship's generator plant or at rough sea condition in a propulsion engine. In this paper, authors propose a new method to control a fuel before the change of angular velocity due to load change by feedforward the change of load, and find that the proposed method shows quite a good control performance in comparision to the customary PID control method by simulation using a digital computer for the various load change.

• 한국분무공학회지
• /
• 제14권1호
• /
• pp.34-38
• /
• 2009

This paper presents the pulsation of carburetor inlet and outlet pressure of a small SI gasoline engine. The engine used in this paper is a 23cc, single cylinder, diaphragm carburetor, two-stroke, air-cooled for brush cutter. The rpm and pressure wave pulsation at the inlet and the outlet of carburetor were measured and analysed for the understand of the internal air flow into the barrel on the diaphragm carburetor. These data should be used for the development of the duel fuel injection system for gasoline and LPG. The results showed that the carburetor inlet pressure variations were very steady, but the pressure variations at carburetor outlet were very sensitive to the pressure variation into the crank case and were to similar independently to the engine speed on partial opened throttle conditions. According to increasing engine speed, the pressure waves started to come out and be developed after closing the intake port of the engine at carburetor outlet. Reverse flow occurred on the WOT (wide open throttle) condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권2호
• /
• pp.159-169
• /
• 1985

The calculation of torsional vibration for marine diesel engine propulsion shafting is normally carried out by equalizing exciting energy to damping energy, or using the dynamic magnifier. But, with these methods, the vibration amplitudes are calculated only for resonance points and vibration amplitudes of other running speeds of engine are determined by the estimation. Recently, many energy-saving ships have been built and on these ships, two-stroke, supercharged, super-long stroke diesel engines which have a small number of cylinders are usually installed. In these cases, the first order critical-torsional vibrations of these engine shaftings appear ordinarily near the MCR speed and the stress amplitudes of their vibration skirts exceed the limit stress defined by the rules of classification society. To predict the above condition in the design stage, the synthesized vibration amplitudes of all orders which are summed up according to their phase angles must be calculated from the drawings of propulsion shaft systems. In this study, a theoretical method to fulfill the above calculation is derived and a computer program is developed according to the derived method. And a shafting system of two-stroke, super-long stroke diesel engine which was installed in a bulk carrier is analyzed with this method. The measured values of this engine shafting are compared with those of calculated results and they show a fairly good agreement.